Grace Company Presser Foot Collar Operating instructions

Brand
Grace Company
Model
Presser Foot Collar
Type
Operating instructions

Grace Company Presser Foot Collar

The Grace Company Presser Foot Collar is a versatile accessory for your sewing machine that allows you to quickly and easily swap between a variety of presser feet. This can save you time and effort, especially if you frequently use different presser feet for different sewing tasks.

The Presser Foot Collar is easy to install and use. Simply remove the screw attaching the hopping foot to the hopping foot collar on your machine, remove the needle bar thumb screw and pull out the needle, loosen the hopping foot collar screw, slide the new hopping foot collar onto the press bar, place the new standard hopping foot onto the hopping foot collar bar, and tighten the hopping foot screw.

Grace Company Presser Foot Collar

The Grace Company Presser Foot Collar is a versatile accessory for your sewing machine that allows you to quickly and easily swap between a variety of presser feet. This can save you time and effort, especially if you frequently use different presser feet for different sewing tasks.

The Presser Foot Collar is easy to install and use. Simply remove the screw attaching the hopping foot to the hopping foot collar on your machine, remove the needle bar thumb screw and pull out the needle, loosen the hopping foot collar screw, slide the new hopping foot collar onto the press bar, place the new standard hopping foot onto the hopping foot collar bar, and tighten the hopping foot screw.

Installation Instructions:
SHCS M3 x 8 mm
HDW-03-10966
(Preinstalled)
A A
B B
2
2
1
1
DO NOT SCALE DRAWING
M3 Thumb Screw
SHEET 1 OF 1
UNLESS OTHERWISE SPECIFIED:
SCALE: 4:1
WEIGHT:
REV
DWG. NO.
A
SIZE
TITLE:
NAME
DATE
COMMENTS:
Q.A.
MFG APPR.
ENG APPR.
CHECKED
DRAWN
FINISH
MATERIAL
INTERPRET GEOMETRIC
TOLERANCING PER:
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
ANGULAR: MACH
BEND
TWO PLACE DECIMAL
THREE PLACE DECIMAL
APPLICATION
USED ON
NEXT ASSY
PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
<INSERT COMPANY NAME HERE>. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
<INSERT COMPANY NAME HERE> IS
PROHIBITED.
Parts List:
The Presser Foot Collar can be used to quickly swap between a variety of foot accessories for your
machine.
Use:
Presser Foot Collar SM19
SMP-09-14525
Use a 3 mm Allen wrench to remove the
screw attaching the hopping foot to the
hopping foot collar on your machine.
Hopping
Foot Collar
Hopping
Foot Screw
Remove the needle bar thumb screw and
carefully pull out the needle.
2
Needle Bar
Thumb Screw
Standard Hopping Foot
SMP-04-10057
1
Q’nique19 Machine
Presser Foot Collar
Instructions
Slide the hopping foot height tool
under the hopping foot, tting the groove
around the needle. Tighten the hopping foot
screw with a 3 mm Allen wrench.
With a 3 mm Allen wrench, loosen the
hopping foot collar screw just enough so that
the collar can be pulled o the machine.
3
Hopping Foot
Collar Screw
Slide the new hopping foot collar that
came with this kit onto the press bar. Make
sure the bottom of the collar is even with the
bottom of the press bar. Hold in place with
the hopping foot collar screw.
New
Hopping Foot
Collar
4
Installation Instructions Continued:
Place the new standard hopping foot onto
the hopping foot collar bar. Attach with a hopping
foot screw loosely enough that the hopping foot
can slide up and down.
Reinstall your machine’s needle and
needle thumb screw (see your machine
manual for details).
6
5
Carefully lower the needle to the lowest
position.
New Standard
Hopping Foot
8
7
Press Bar
Hopping Foot
Height Tool
Copyright May 19, 2021 Version 1.0 Grace Company
  • Page 1 1
  • Page 2 2

Grace Company Presser Foot Collar Operating instructions

Brand
Grace Company
Model
Presser Foot Collar
Type
Operating instructions

Grace Company Presser Foot Collar

The Grace Company Presser Foot Collar is a versatile accessory for your sewing machine that allows you to quickly and easily swap between a variety of presser feet. This can save you time and effort, especially if you frequently use different presser feet for different sewing tasks.

The Presser Foot Collar is easy to install and use. Simply remove the screw attaching the hopping foot to the hopping foot collar on your machine, remove the needle bar thumb screw and pull out the needle, loosen the hopping foot collar screw, slide the new hopping foot collar onto the press bar, place the new standard hopping foot onto the hopping foot collar bar, and tighten the hopping foot screw.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents