Kocom KLP-410 Series User manual

Brand: Kocom

Model: KLP-410 Series

Category: Door intercom systems

Type: User manual

Kocom KLP-410 Series

The Kocom KLP-410 Series is a multiplex house lobby phone system that allows users to communicate with visitors and control access to their building. The system includes a variety of features to enhance security and convenience, including:

Audio and video communication: The system allows users to see and speak with visitors before granting them access to the building.
Remote door release: Users can remotely unlock the door for visitors using the included key fob or a mobile app.
Motion detection: The system can be configured to detect motion in front of the door and send an alert to the user's smartphone.

Kocom KLP-410 Series

Audio and video communication: The system allows users to see and speak with visitors before granting them access to the building.
Remote door release: Users can remotely unlock the door for visitors using the included key fob or a mobile app.
Motion detection: The system can be configured to detect motion in front of the door and send an alert to the user's smartphone.

KLP-410 series



[Multiplex House Lobby Phone User/Installation Manual]

■ Household call & conversation feature

■ Guard call & conversation feature

■ Routed guard call feature

■ Automatic door open feature using common PIN code

■ Automatic door open feature using household PIN code

■ Automatic door open feature using RF-Card (※KLP-C410R)

KLP-410 Series



KLP-410 series N0326

SINCE

1976

KOREA COMMUNICATIONS CO.,LTD

http://www.kocom.com

E-mail : [email protected]

This manual is based on the date as shown in the right and specifications are subject to

change without notice for quality improvement

Warranty

Warranty Card

1. Name of the product.

2. Model number of the product.

3. The area of problem.

4. Phone number and address at which you can be contacted.

1) This product is produced under strict quality control and inspection procedures.

2) If this product breaks down during proper use as a result of product defect, KOCOM

will repair it within one year from date of purchase free of charge.

3) The following cases will be subject to charge, even during warranty period:

a. Breakdown during transport, or through careless treatment, by consumer.

b. Breakdown cause by unauthorized repair, or system modification.

c. Breakdown caused by natural disaster or power disorder.

PRODUCT

MODEL

DATE PURCHASED

WARRANTY PERIOD

AGENCY ADDRESS

KOCOM Warranties the original purchaser of this product as follows.

To receive after service, have the following ready before you

contact our branches.

www.kocom.com







For safe use, please stick to the following cautions.

·Please, save this manual after reading these instructions carefully. ·Read and understand all instructions to set up rightly.

·This Cautions for Safety may include items that are not contained in specifications of the product that consumer purchases.

·If you need assistance with the set-up or operation, please contact with A/S center.

To help our customers to understand this manual, to prevent any personal injury or property damage, some marks are used in the manual.

The marks and the drawing signs are below. Please, understand the marks before reading the manual.

Cautions for set-up

The important marks in the manual.

The meaning of the drawing signs.

Sign to show what not to do Mishandling the device with ignoring this sign may result in serious injury or death.

Mishandling the device with ignoring this sign may result physical injury or material damage.

Sign to tell you that you should follow the instructions. Sing to tell you that you need more attention including high voltages, electric shock, danger, warning)

Sign to tell you that you can't disassemble this unit. Sign to tell you that you must unplug the unit.

·The law limits distributing the power lines to an authorized person from government. The work from an unaurhtorized person cause fire or electric shock.

·Place this unit securely on a stable surface. Serious damafe and/or injury may result if the unit falls.

·Do not set up this unit near the leaking place because it may expose you to dangerous voltages or other risks.

·Even if your product is water proof, do not install it slanted place of water leakage, which can a short circuit.

·The work of distributing wires needs skills and experiences. So please, for assistance, contact your dealer or call service center.

·The communication lines should be built in being distant from the power source. This may result in the risk of fire, electric shock and communication disorder.

·Setting the communication lines in a high humid place such as outside without any protection from rain causes the communication disorder.

·Keep the hook at the wall-mounted device safe. The hook may cause the physical injury.

·Think about the thickness and quality of wall material. The unqualified material may make the device fall.

Warnings for Usage

·Do not install this unit near the water and dust, for example, in a bathroom or near the washing machine. It caused fire and electric shock.

·Do not install this unit near the fire, for example, near kitchen sink, heater or the like.

·Do not install near the noxious gar such as Hydrogen Sulfide, metal power and the like.

·Do not install near the water and chemicals.

·Do not give any damage, break and modify the plug. Overloading, heating, pulling causes the damage.

·Do not place the plug near the heater. The damaged code causes fire and electric shock. Do not pull the power code when unplugging.

·The damaged code causes fire and eclectic shock. Must pull with plug. Do not touch with wet hands. It causes the electric shock.

·Do not use any other voltage, except the marked regular voltage.

·Do not use the power terminal at the units to other electric device except the designed device.

·Do not install the units at the leaking place if it doesn’t have any waterproof mark. Do not install the unit when the power is on.

·Install the circuit breaker after checking the safety such as electric shock and leakage. Turn off the power before you install or A/S

·Check the suitability of the lines for installing when you use the exiting lines.

·Do the wiring work by using the designed material.

·Connect the electric wire with the designed ways and ground.

·Do not connect with any other devices except the designed devices to compose the system.

·Unplug electric wire and communication lines from the units before moving to another place.

·Unplug this device when you want to check the inside. If there is no plug, please, turn off the circuit breaker.

·Unplug this device when you try to move it to another place. If the electric line is connected inside of the unit, please contact your dealer or service center.

·Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning

Cautions for Repairs and Maintenance

·Keep the inside of the device clean. Having the dust inside without any cleaning for a long time causes the fire. If necessary, contact your dealer or service center to get cleaning service.

·Set the device of the wall-mounted type not to fall. Falling from an earthquake causes personal injury.



·Change the damaged electric code.

·Unplug this unit from plug socket and refer servicing to an authorized service center when the following conditions occur:

·If liquid has been spilled into the unit. 쪾·If the unit does not work normally by following the operating instructions.

·If the unit exhibits a distinct change in performance. 쪾·If the unit has been dropped or physically damaged.

·Do not disassemble this unit at will as this device is composed by precision parts. 쪾·Install the unit by following the set-up instructions of Kocom.

·Do not touch or insert any foreign substances, for example, sticker, magnetic, opener and the like

·Make U-type at the end of wires as the rain can effect on the system by following the wires during the rainy season.

Cautions for Use

Cautions for Abnormality

Safety Instructions, Warnings and Cautions of Each System

·This unit is not designed for security purpose. 쪾·Do not handle the unit with the wet hands.

·Do not place a pot with water or a small metal material on the Units.

·Do not cover the ventilating opening or put any metal material in the units. 쪾

·During thunderstorms, avoid using this unit. 쪾There may be a remote risk of an electric shock from lighting.

·Do not modify the unit. ·Open the main gate after checking ID if the image and sound system do not work. Call A/S

·Do not disassemble the back and cabinet cover.

·Separate the AC/DC lines with the hook of the wall-mounted type when installing. 쪾·Connect the lines after peeling the wires properly

·Do not distribute signal line with AC line. 쪾·Use the designed driver to connect the lines to terminal

·Do not clean the LCD with the damp cloth for cleaning. Use the only dry and soft cloth. 쪾·Do not install the main gate monitor at the leaking place.

Videophone

·This product is designed as a home videophone and cannot use continuously like monitor camera.

·If there is temperature difference between inner part of camera and surrounding, dew condensation occurs on camera lens and may disturb image.

If dew condensation is removed from camera lens, image quality recovers.

·White LED light examination range is narrower than camera shot range at night, so there is less amount of light at night than day.

So it is difficult to see the face in low illumination condition due to noise increase on screen, but it is not from defect.

·Monitor screen (liquid crystal panel) is not in defect when some pixels always light or black out.

·Please install monitor and camera over 5cm away. Also, avoid installing at a place with too much noise, because too much noise around camera causes phone call inferiority.

·Do not place an object within 20cm in front of monitor. It causes phone call inferiority, especially because microphone is installed at the top of monitor.

·If strong light such as sunlight flows into camera module, screen saturation (or strange mark) and image shaking might occur.

·This is not a defect, so please do not install camera where a direct ray of light do not flow if possible.

Things You Need to Know

·In some cases there is occurrence of product destruction, malfunction, noise mixing and picture quality deterioration due to mixing of other tool’s induced

voltage or thunder with communication wiring of monitor/camera, monitor/extended monitor.

Do not wire with power line such as outdoor wiring or AC power, or phones and other tools.

·You cannot use it if you incorrectly wire the AC voltage between monitor/camera, monitor/extended monitor. Call the store or agency where you purchased

this product and consult to solve the problem.

Beware that unfixable damage might be caused due to authorizing AC voltage on communication wiring of monitor/camera, monitor/extended monitor.

·Do not ever disjoint this product. It may cause electrocution accident when touching high-voltage circuit inside this product.

·Outside power authorizing this product must be confirmed of product description and use rated voltage. Beware that if higher voltage is authorized, unfixable

damage might be caused due to product destruction.

·Power must be connected to domestic voltage (product rated voltage) consent or interior wiring.

If connected to other motive power or inverter-type power, product destruction, noise mixing, and picture distortion may occur.

·Do not drop this product. Glass is used for monitor and might break, or cause other circuit inferiority.

In such case, immediately turn down the power switch, and call to consult agency or store in which this product was purchased.

·If installed near transmission antenna such as broadcasting station, electric wave may mix and cause picture distortion or voice mixing.

·Avoid installing near tools with strong electromagnetic waves such as microwaves and cell phones, or it may cause picture distortion.

·Do not install monitor in following places.

① Above or around water heater, rice-cooker, heater ② Place exposed to direct rays of the sun ③ Place with temperature below 0'C such as cold store

④ Place with high humidity such as bathroom, washroom, heated room

⑤ Place with a lot of gas, dust, smoke ⑥ Dangerous place with sprays of water or chemicals

·Do not wipe with insecticide, drugs or chemicals such as thinner and alcohol, or it may damage

the surface of this product.

·Beware of occurrence of image quality deterioration or malfunction from cause of humidity due to

penetration of chemicals or water into camera’s urea resins.

·As in the picture, it prevents temperature difference of camera (outside) and monitor (inside), and

removes dew condensation caused by humidity of camera window.

·Camera must be installed when wall cement is completely dry.

·When product is installed in winter below -5'C, wait for approximately 2 hours to connect. Dew formation

in monitor and camera due to temperature difference inside and outside may cause product defect.

·Avoid installing monitor and camera in place directly exposed to heat or where gas noxiousness is

highly occurring.

Cautions

Stop up P.V.C pipe using

adiabatic substances, to

prevent air circulation

Tubing Box Monitor

Pipe

Camera

(Outdoor, Door)

Based on 15V/2A (Adaptor specification)

Distance between lobby phones is within

10M when connecting 2 lobby phones

Based on 15V/2A (Adaptor specification)

Distance between lobby phones is within

10M when connecting 2 lobby phones

Door camera

15V/ 2A

Adapter specification (Based on 1 set)

Additional Adapter

Installation

1. Able to connect 2 lobby phones(when distance of

each lobby phone from adaptor is with in 10M)

2. Need to add Adaptor when install lobby phone

1 set + more than 20 sets of interphone.

Additional adaptor is required to install for

every additional 20 interphones.

CNT14

①

CNT12

CNT14

①

CNT12

Multiple Apartment System Line

(Common wire)

Terminal Box

Multiple Apartment System Line

(Common wire)

Terminal Box

Guard

master

5 wires for interphone wiring

(Powered by lobby phone)

1) DC+15V~18V

3) GND

4) VOICE 1

5) VOICE 2

7) DATA

8) Automatic Door +12V

9) Automatic Door GND

8) Automatic Door +12V

9) Automatic Door GND

8) Automatic Door +12V

9) Automatic Door GND

8) Automatic Door +12V

9) Automatic Door GND

GND/Voice 1/Voice 2/DATA (4 wires)

polarized IV 0.8mm and above can be used

Power (+18V/GND) (2 wire) polarized IV 1.2mm and

above can be used

Video signal/GND use coax cable: Use 5C-2V

GND/Voice 1/Voice 2/DATA (4 wires) polarized IV

0.8mm and above can be used

Power (+15V/GND) (2 wire) polarized IV 1.2mm

and above can be used

Guard

master

4 5

Wiring Diagram Wiring Diagram

OUTPUT

INPUT

OUTPUT

Coax cable UTP

Coax cable

OUT

PUT

OUT

PUT

INPUT

Maximum 3 sets of lobby phone can be added.

4 4

DVR

15V/ 2A

Door camera

①

① ①

①

① ①

6 7

Name of each part

Installation

Product Spec

Mic : Voice input

Guard Call Button :

Used to call guard

Cancel Button :

Used to cancel calling

KLP-C410

Power Source

Power for internal operation

Lobby Phone Data Type

Call Type Hands-free Type (2-Way)

PROTOCOL DATA TX/RX Type

Call & Video Waiting Time

30 second waiting time after call, 3 minutes for call to household.

Housing Material

Aluminum (A/L), PC, ABS

Dimension

(W)174 X (H)263 X (D)15 (mm)

Guaranteed Operation

Temperature

-10℃~50℃

LED On Feature

10-Key LED turned on for calling

Video Angle

Feature to adjust up, down, left, right (90°) None

Link with RF Card

Not linked 13.56MHz

DC 12V

DC 15V~18V

(Standby:4W, Operation:10W)

Product Name

KLP-C410R

DC 15V~18V

(Standby:4W, Operation:10W)

Not linked

KLP-D410

DC 15V~18V

(Standby:3W, Operation:7W)

Components of product

1,500

1,220

1,780

Back case

Main Body

Box

Lobby Phone Sun visor(Option)Box(Option)

Mood Lamp :

Turns on to find it in night time

RF Card Reader :

Door opens by contacting of RF Card

(Available only with RF Card Model)

FND Display :

Displays household

number and during setup

10 Key Dial Button :

Displays household

number and during setup

Camera Lens :

Send video image during call

Call Button :

Used to call household

90°

Wiring Diagram

●For link with sensor :

- Setup

JP1 : No relation

SW2 :

- Wiring

Pin 7 of CNT7 : Fire sensor (+)

Pin 9 of CNT7 : Fire sensor (-)

Pin 8 of CNT7 : PIR sensor (+)

Pin 9 of CNT7 : PIR sensor (-)

Sensor_GND

●External power connection with Dead bolt

Pin 5 of CNT7 - Dead bolt_GND

Pin 6 of CNT7 Connect to Dead bolt +

■Lobby Phone Terminals

■Lobby Phone Terminal Connection

●For link with dead bolt :

Dead bolt consumes a lot of current, so it is

essential to connect external power.

- Setup

JP1 : Connect pin 1-2

SW2 :

- Wiring

Pin 8 of CNT12 Dead bolt +12V

Pin 9 of CNT12 Dead bolt_GND

JP1

CNT12

CNT7

CNT14

CNT4

SW2

●For link with Automatic Door :

- Setup

JP1 : Connect pin 2-3

SW2 :

- Wiring

Pin 6 of CNT7-Connect Automatic door contact + and

Pin 8 of CNT12-Automatic door contact-(No polarity)

●For link with Striker :

- Setup

JP1 : Connect pin 1-2

SW2 :

- Wiring

Pin 8 of CNT12 Striker +12V

Pin 9 of CNT12 Connect Striker_GND

●Open/Close Contact

N/O

COM

N/C

A B

JP1

SW2

CNT14 (Video Output)

8) GND

7) DVR VIDEO Output

6) GND

5) GND

4) Additional Lobby Video Input 2

3) Additional Lobby Video Input 1

2) VIDEO2 Output

1) VIDEO1 Output

CNT12 (for household connection)

9) Switch_GND

8) Switch Output (+)

7) DATA

6) VIDEO 1 Output

5) Voice2

4) Voice1

3) GND

2) NC

1) DC+15V

CNT7 (Sensor & Switch)

10) Fire & PIR sensor Power (+)

9) Fire & PIR sensor contact & GND

8) PIR sensor contact (+)

7) Fire sensor contact (+)

6) DOOR_SW_+/DEAD_BOLT_POWER+

5) DEAD_BOLT/ STRIKER_GND

4) Not Used

3) N/C Contact

2) COM Contact

1) N/O Contact

CNT4 Connection

3) GND

2) NC

1) +15V

JP1(DOOR TYPE)

2) N/O for 2, 3 connection

1) N/C for 1, 2 connection

Body Sensor

On the basis of

the center of

lobbyphone’s

lens

(Unit : mm)

Standard installation height of lobbyphone is 1,400~1,450mm

from floor to the bottom of flush mounting box.

In case that the installation height of lobbyphone is out of the

range (min.1,250mm~1,550mm), it’s hard to get proper

image, so be careful about the installation height of lobbyphone.

■Standard height for installation of Lobbyphone

Sub videophone 8P*300mm

Power 2P*300mm

Household 9P*300mm

DC 15V~18V / 2.0A Adapter

Sensor & Switch 10P*300mm

4×30mm Screw (4ea)

4×10mm Screw (2ea) 4×8mm Bolt (2ea)

3×12mm Screw (1ea)

“L”wench

Please change the master Pin code after installation.

① - System PIN Number Setup Menu

② - Common PIN Number Setup Menu

③ - Lobby Door Open On-Time Setup Menu

④ - Guardroom Routed Call/Interphone Setup Menu

⑤ - RF-Card Registration Menu

⑥ - RF-Card Deletion by Household Menu

⑦ - All RF-Card Deletion Menu

⑧ - Lobby Phone ID Setup Menu

⑨ - Use of DVR Link Setup Menu

⑩ - System Link Version Setup Menu

⑪ - English/Korean Comment Setup Menu

▷Entering Menu Setup

▷Function to open lobby door using household PIN number

▷LED Operation Mode Functions

Pressing [*] and [#] at the same time in waiting status will blink [MEnu] for 2 seconds at FND, and display [- - - -] for PIN number input.

It enters to PIN number setup menu after pressing system PIN number followed by [#]. (Default pin code : 9999)

▷System PIN Number Setup

FND displays [- - - -]after blinking currently registered system PIN number twice when pressing [Cancel]button from System PIN Number Setup menu.

Now, pressing new 4 digit PIN number and pressing [#] button. It will blink entered PIN number twice and setup is completed,

and it will display next setup menu of “Common PIN Number Setup”.

▷Common PIN Number Setup

Pressing [Cancel]button from Common PIN Number Setup menu will blink currently registered common PIN number twice and FND displays [- - - -].

Now, input new 4 digit PIN number and press [#] button. It will blink new PIN number twice and setup is completed, and it will display next setup

menu of “Lobby Door Open On-Time Setup”.

hhhh 0100

[Enter Menu]

[Menu] blinks for

2 seconds

Enter PIN

number

Completion

button

[Program Version]

blinks for 2 seconds

[System PIN

Number Set]

▷Menu display and switching between menu

Menu is switched to next menu every time pressing [Guard] button.

Frequently used menus of 1~10 can be directly accessed by pressing 1,2,3,4,5,6,7,8,9,0 numeric key.(Pressing 0 will move to Menu 10.)

Menu 11, “English/Korean Menu” can be accessed by pressing [Guard] button.

9EPS

LBPS 8282

Enter new

PIN number

1234

Current PIN

number blinking

[System PIN

Number Setup]

Change

completion

[Enter Menu]

9EPS 8282

Enter new

PIN number

1234

Current PIN

number blink

Setup menu

display

Change

completion

[Enter Menu]

----

Waiting

for input

----

Waiting for

input

hhhh

[Enter Menu]

[Menu] blinks

for 2 seconds

4,5,6,8,0 Input

Completion

button

[LED Operation

Mode 0]

[System Waiting

Status]

[Menu] blinks

for 2 seconds

Completion

button

[LED Operation

Mode 1]

[System Waiting

Status]

hhhh

[Enter Menu] 1,2,3,8,0 Input

hhhh

Household PIN

number input

0101

Household

number input

Door openedCompletion

button

[- - - -] appears at FND when pressing [#] button after pressing household number. Pressing 4 digit PIN of corresponding household and [#] will

open lobby door that is connected with lobby phone. [OPEn] is displayed at FND with tone sound.

Lobby door is opened only for set time.

One PIN number is allowed for each household.

Pressing [*] and [#] at the same time in waiting status will blink [Menu] for 2 seconds at FND, and display [- - - -] for PIN number input.

LED Operation Mode 0 Setup : FND displays [Led.0.] when pressing 4,5,6,8,0 and [#] in sequence from [- - - -] state, and it sets LED Operation Mode 0.

LED Operation Mode 1 Setup : FND displays [Led.1.] when pressing 1,2,3,8,0 and [#] in sequence from [- - - -] state, and it sets LED Operation Mode 1.

It is returned to waiting state with LED turned off after 2 seconds (LED is on when touching touch panel).

Touch panel (Key) front LED is always on.

LED in normally off, and is turned on when

user touches touch-panel (Key).

Caution

Setup Setup

▷ Guardroom Routed Call Setup

Pressing [Cancel] button from Guardroom Routed Call menu will blink currently setup value [no] to FND, and the light is on.

Now, set whether user would Guardroom Routed Call function. Selecting 1 means to use the function, and selecting 0 means not to use the function.

Select whether to use the function or not, and press [#] button. It will blink the selected status that indicates setup completion, and display the next

setup menu of “RF-Card Registration”.

▷RF-Card Registration

Pressing [Cancel] button from RF-Card Registration menu will blink household input waiting status [Sd.id.] to FND, and [____] appears to input the

household number.

Input the household number to register the RF-Card, and press [#] button. It will display [Card].

Contact the RF-Card to the reader when [Card.] appears, then the RF-Card is registered.

“[[]]”appears when registration is successful, and [Card.]appears again in a few second to register other RF-Card so user can register multiple cards.

It will automatically return to RF-Card Registration menu after specified period (15 seconds).

RF-Card can be registered up to maximum 1000 cards without regard to the number of households.

▷ RF-Card Deletion by Household Menu

Pressing [Cancel] button from RF-Card Deletion by Househole menu will blink household input waiting status [Sd.id.] to FND, and [____] appears

to input the household number.

Input the household number to delete the RF-Card, and press [#] button. It will display [C.dEL.]. After a few seconds, RF-Card Data is deleted for

corresponding household and blink“[[]]”to indicate deletion is completed, and [____] appears again to input household number for other RF-Card

to delete

Input the household number and press [#] button. It will delete corresponding household’s RF-Card Data.

Current

status blink

Enter new number (0, 1)

to set whet to use the function

Setup Menu

Display

Change

completion

Change

Button

YES

Household

Number ID

Setup Menu

Display

Input

completion

Change

Button

Input Household

Number

1004

Registration

completion

[[ ]]

Wait for

RF-Card input

Wait for

RF-Card input

____

Wait for input

Household

Number ID

Setup Menu

Display

Input

completion

Change Button Input Household

Number

1004

Deletion

completion

[[ ]]

____

Wait for input

____

Wait for RF-Card

input

▷ All RF-Card Deletion Menu

Pressing [Cancel] button from All RF-Card Deletion menu will display [dEL.?] in FND that asks whether the user really wants to delete all RF-Card.

Pressing [#] button will count up from [d.001]~[d.470], and display “[[]]” when it is completed, and display All RF-Card Deletion menu [A.dEL.].

Household

Number ID

Setup Menu

Display

Input

completion

Change

Button

Last number

of deletion

start of deletion

[[ ]]

Deletion

completion

Display Setup

▷Lobby Door Open On-Time Setup

Pressing [Cancel] button from Lobby Door Open On-Time Setup menu will blink currently setup value [t-02] to FND, and the light is on.

Now, press 1~8 to change the value and press [#] button. It will blink registered Door Open On-Time time and setup is completed, and it will

display next setup menu of “Guardroom Routed Call Setup Menu” (The unit of time is second).

Current Door Open

On-Time blink

Enter new Door

Open On Time

Setup Menu

Display

Change

completion

Change

Button

▷Register household PIN number

[----] appears at FND when pressing [#][#][0][0][#] in sequence during call with household device.

Now, enter PIN number and press [#] button, and household PIN number is registered with [P.YES.] display.

0 0

p .yes.

PIN registered

HHHH

Enter PIN

Change

Completion

During call

with household

----

Input Hold

10 11

Setup Setup

PIN Number Input

Completion blinking

Move to next setup menu

PIN Number Input

Completion blinking

Move to next setup menu

RF-Card

Registration

completion

RF-Card

Input Household

Number

Input Household

Number

Return to “RF-Card Registration Menu” by pressing * button or after certain time.

②Common PIN Number Setup

Enter new PIN

number

Current PIN

number blinking

Enter new PIN

number

Current PIN

number blinking

①System PIN Number Setup

③Lobby Door Open On-Time Setup

Current setup

time blinking

Current setup

time blinking

Entered setup time

Blink

Entered state

⑤RF-Card Registration

④Guardroom Routed Call

Interphone Setup

Blink

Deletion

Completion

Wait for Household

Number

⑥RF-Card Deletion

by Household

⑦All RF-Card Deletion Are you sure to

delete all?

Deletion start

number

Deletion end

number

Deletion

Completion

[Program Version Display]

Wrong PIN

Number

(3 Times)

Correct PIN

Number

System

PIN Number

→ #

Blink

Enter PIN Number

[Lobby Phone in

Waiting Status]

[Press at the

same time]

Enter System PIN Number

1~8 Input

‘7’Enter number

‘1’Enter number

1 is set to use the function, 0 is set to not use the function

1 digit number input #1

1. Pressing menu number buttons ①②③④⑤⑥⑦⑧⑨⑩ move directly to corresponding

menu. However, menu ⑪ is selected by pressing [Guard] button.

2. Pressing [*] button from each setup menu display state will cancel the menu setup,

and it is returned to Lobby Phone Waiting [ -] state.

3. Pressing [*] button from each setup input state will return back to menu setup state.

4. The system password is 9999 when the factory ships the products.

hhhh

____

Return to “RF-Card Registration Menu” by pressing * button or after certain time.

Return to “All RF-Card Deletion Menu” after deletion completion

⑧Lobby Phone ID Setup Current Lobby

Phone ID

Waiting for

ID Input

Input new Lobby

Phone ID

ID Input Completion

(Blink)

⑨Use of DVR Link Setup

Current setup status Input status

Input Completion

(Blink)

Input Completion

(Blink)

Input Completion

(Blink)

‘1’Enter number

1 is set to use the function, 0 is set to not use the function

1 digit number input #2

1 is set to use Version 1 (New), 0 is set to Version 0 (Old)

1 digit number input #3

⑩System Link Version Setup

Current setup status Input status

‘1’Enter number

⑪English/Korean

Comment Setup

Move to first “① System PIN Number Setup”

Current setup status Input status

‘1’Enter number

▷ Use of DVR Link Setup Menu

■ General scenario by setup menu and each button

Pressing [Cancel] button from Use of DVR Link Setup menu will blink currently setup status [no] to FND, and the light is on.

Now, input whether to use DVR Link. Selecting 1 means to use the function, and selecting 0 means not to use the function.

Select whether to use the function or not, and press [#] button. It will blink the selected status that indicates setup completion, and display the next

setup menu of “System Link Version Setup Menu”.

Current

status blink

Enter new number (0, 1)

to set whet to use the function

Setup Menu

Display

Change

completion

Change

Button

YES

Current status

blink

Select System (0, 1) Setup Menu

Display

Change completionChange

Button

▷ System Link Version Setup Menu

Pressing [Cancel] button from System Link Version Setup Menu will blink currently setup status [Pr-0] to FND, and the light is on.

Now, select the version to link with the system and enter it.

Selecting 0 means to use the Communication Protocol-0 (Old Version) for this system.

Selecting 1 means to use the Communication Protocol-1 (New Version) for this system.

Select System Link Version and press [#] button. It will blink the selected status that indicates setup completion, and display the next setup menu

of “English/Korean Comment Setup Menu”.

▷ English/Korean Comment Setup Menu

Pressing [Cancel] button from English/Korean Comment Setup Menu will blink currently setup value [no] to FND, and the light is on after 2 second.

Select and enter English/Korean Comment. Selecting 1 means to use English Comment, and selecting 0 means not to use English Comment.

Not selecting English Comment means to use Korean Comment.

Select which comment to use and press [#] button. It will blink the selected status that indicates setup completion, and display the next setup menu

of “System PIN Number Setup”.

▷ Changing the English/Korean Comment selection using fixed PIN number

Pressing [*] and [#] at the same time in waiting status will blink [Menu] for 2 seconds at FND, and display [- - - -] for PIN number input.

(1) Korean Comment Enter fixed PIN number (137950) for English/Korean Comment Change and press [#]. It will display [ENGL]->[ no] and

change to Korean Comment is completed. System will be in waiting mode.

Setup Menu

Display

Change

Button

Current status

blink

Select

Comment (0, 1)

Change

completion

YES

01.00

Setup Menu

Display

Change

completion

Change

Button

Enter Lobby

Phone Numbe

Waiting for inputCurrent Lobby

Phone ID blink

▷ Lobby Phone ID Setup

Pressing [Cancel] button from Lobby Phone ID Setup menu will blink current Lobby Phone ID number [Lb.01.], and displays [Lb.--] that can input

Lobby Phone ID number.

Now, input Lobby Phone ID number and press [#] button. It will complete Lobby Phone ID change, and it will display next setup menu of

“Use of DVR Link Setup Menu”.

hhhh

[Enter Menu] [Menu] blinks fo

2 seconds

Enter fixed PIN

number

Completion

button

Display Comment

Menu(for 1 second)

Set to Korean Comment

(displayed for 1 second)

System

Waiting Mode

(2) English Comment - Enter fixed PIN number (137958) for English/Korean Comment Change and press [#]. It will display [ENGL]->[ YES] and

change to English Comment is completed. (All sound is expressed in Tone voice when English Comment is selected.)

LBPS

9EPS

8282 82821234

____

8282 82821234

____

YES YES

1004 [[ ]]

____

[[ ]]

YES YES

hhhh

[Enter Menu] [Menu] blinks fo

2 seconds

Enter fixed PIN

number

Completion

button

Display Comment

Menu(for 1 second)

Set to English Comment

(displayed for 1 second)

System

Waiting Mode

Household

Number

Household

Number

YES

Kocom KLP-410 Series User manual

Brand: Kocom

Model: KLP-410 Series

Category: Door intercom systems

Type: User manual

Kocom KLP-410 Series

Audio and video communication: The system allows users to see and speak with visitors before granting them access to the building.
Remote door release: Users can remotely unlock the door for visitors using the included key fob or a mobile app.
Motion detection: The system can be configured to detect motion in front of the door and send an alert to the user's smartphone.

Download PDF

report

Kocom KLP-410 Series User manual

Kocom KLP-410 Series User manual

Related papers

Other documents