Qeedji SLATE Series User manual

User Manual

SLATE106

1.11.10 001C

1

Legal Notice

User Manual SLATE106 1.11.10 (001C_en)

Rights and Responsibilities

and services mentioned in this document may be trademarks and/or trademarks of their respective owners. The publisher and the author do not pretend to these

brands.

Although every precaution has been taken in the preparation of this document, the publisher and the author assumes no responsibility for errors or omissions, or for

damages resulting from the use of the information contained in this document or the use of programs and source code who can accompany it. Under no circumstances

can the publisher and the author be held responsible for any loss of profits or any other commercial prejudice caused or that would have been caused directly or

indirectly by this document.

Product information

The conception and specifications of the product may change without prior notice, and this applies to hardware, embedded software and this guide. Consumable items

accessories may slightly differ than herein described as Qeedji is depending on the evolutions of its suppliers. This document contains confidential information; it can’t

be disclosed to any third parties without prior written authorization of INNES.

Safety instructions

Please read carefully the following instructions before switching the product on: - WARNING! Correct fitting and installation is of the utmost importance. Incorrect fitting

and/or installation may result in personal injury or loss. Qeedji disclaims all liability, of whatever kind, if the product is assembled, fitted and/or installed in an incorrect

manner. - Do not use the product near a water supply. - Do not pour anything on the product, like flammable liquids or material. - Do not expose the product to direct

sun, near a heating source or a dust nor vibrations. - Do not obstruct holes, to be sure that air flows freely around the product. - Switch off the product during a storm. -

Do not open the product in any circumstances.

Guarantee terms

Qeedji products are eligible for a warranty to cover genuine manufacturing defect for 3 years. Product failure occurring as the result of factors that do not constitute

genuine manufacturing defect are not covered under the terms of the warranty and any repairs of this nature would be chargeable. For example: Inappropriate

maintenance action, a non-authorized modification, a not specified environment utilization (see ‘Safety instructions’), or if the product has been damaged after an

impact, a fall, a bad manipulation or a storm consequence, an insufficient protection against heat, moisture or frost. This warranty is not transferrable. In addition, any

repairs carried out by non-authorized personnel will invalidate the warranty.

WEEE Directive

This symbol means that your end of life equipment must not be disposed of with household waste but must be deposited at a collection point for waste electrical and

electronic equipment or to your reseller. This will benefit the environment. In this context, a system for collecting and recycling has been implemented by the European

Union

2

1.1
1.2
1.3
1.4
1.5
1.6
1.6.1
1.6.1.1
1.6.1.2
1.6.1.3
1.6.1.4
1.6.2
1.6.3
1.6.4
1.6.4.1
1.6.4.2
1.6.4.3
1.6.4.4
1.6.5
1.6.5.1
1.6.5.2
1.6.6
1.6.7
1.6.8
1.6.9
1.6.10
1.7
1.7.1
1.7.2
1.8
1.9
1.10
1.11
Table of Contents
Introduction
Getting started with the device
Peripherals dimensions
Device installation
Batteries
Pictureframe application
Features summary
Spe_desktop
Secondary picture display
Working with a hub
Message Overlay
File system
LED behaviour
Configuration
APPLI.CFG configuration file
APPLI.HTA configuration application
Heartbeat wake-up
Actions matrix configuration
Diagram
Device start-up
State diagram
RTC, Date & time
Software release
Recovery mode
Hardware reset
Batteries level
Mobile applications
Slate Message Overlay
Slate Maintainer (RFU)
Badge reader (RFU)
Technical specifications
Conformities
Contacts
3

1.1 Introduction

This manual explains how to setup your device SLATE106. This device is part of the SLATEs family. It can be used with or without a SMH300 hub.

Recommendations and warnings

This device is designed to be used inside a building.

This device is a Class A device. In a residential environment this device may cause radio interference. In this case, it is recommended to take appropriate measures.

This device is designed to work with 4 CR2430 batteries. Please refer to the

Batteries chapter to know the batteries replacement procedure. The batteries lifetime is

estimated to 3 years with 6 daily .ppk picture updates, with Bluetooth Low Energy synchronization with SMH300 device every 15 minutes, 5/7 days, from 8:00 AM to

7:00 PM. The lifetime can be affected when using vibration features.

Keep in mind that this device is an electronics device and may not support inadvertent fall or violent vibration. In case the device has to be installed on a door, you have

to check that any violent vibration won't be generated on the device especially when closing the door. For the same reason, when the optional wake-up by vibration

feature is activated, the vibration generated when opening or closing the door may imply useless wake-up, which is affecting the battery lifetime.

The warranty does not cover the batteries.

Content of the package

Item Features

Device SLATE106

Batteries 4 CR2430 batteries with plastic holder

Support Mounting bracket and cardboard easel

Screw 2 M2.5x25

Adhesive 3M double sided tape (W x H x D): 65 mm x 19 mm x 0.5 mm

4

1.2 Getting started with the device

Front face

The SLATE106 device has:

3 touch sensing keys

3 red LEDs

1 RFID/NFC sensor

1 vibration sensor

Please find below the location of each peripheral:

1

RFID/NFC antenna

2

Left LED

3

Middle LED

4

Right LED

5

Left key

6

Middle key

7

Right key

8

Internal vibration sensor

1

2

3

4

5

6

7

8

5

Side face

8

USB client cable (Male micro-B)

Rear face

9

Mounting bracket

8

9

6

Device dimensions

151,2

114

8

mm

7

Labelling

The model of the device, the power supply characteristics, the serial number (PSN) and the MAC address are written on a label which is stuck on the case. Some

additional tags may be present in case of built-in options.

☛ The serial number of the device can be requested in case of technical support.

00:1E:C0:40:04:BF

Mac:

5VInput:

SLATE106

5A rue Pierre Joseph Colin

35000 Rennes, FR

PSN00901-00104 CD5

www.qeedji.tech

130mA

3 7 0 0 5 6 8 1 0 5 9 9 1

SLATE106

EAN

www.qeedji.tech

Testcard

At the factory, the device content set by default is the Test Card . The chart displays important information to assist in the device configuration:

SLATE106

Manufacturer: Qeedji (www.qeedji.tech)

PSN: 00902-00077

Firmware rev: 1.10.12

Software rev: 1.11.10

Hostname: slate106

Index: 2

8

1.3 Dimensions

Dimensions in millimeters

Coordinates [X,Y] in pixels

15

151.2

114

3

90.6

122.4

11.7

14.4

6.8

103.9

60.9

17.9

118.1

1

25.6

5.7

2.4

2.5

[0;0]

[799;599]

[688;25]

[109;575]

[117;583]

[125;591]

[390;575]

[398;583]

[406;591]

[671;575]

[679;583]

[687;591]

9

1.4 Device installation

Batteries

Place the SLATE106 device, with the back face in front of you.

Keep the battery in its plastic holder like shown below.

1

CR2430 battery

2

Battery holder

⚠ Warning: check that the battery is inserted in its holder with the right polarity (positive side facing up). In case the battery is not delivered with its holder,

contact [email protected].

Glide the 1st battery

3

with its holder into its place. Use your finger or a screwdriver to push the plastic of the holder part until you feel a clip, meaning that the battery

is properly installed.

Glide the other batteries with its holder in the right orientation like explained on the picture above:

2nd battery

4

,

3rd battery

5

,

4th battery

6

.

Once the batteries are installed, they are all hidden.

1

2

CR2430

+

CR2430

+

CR2430

+

CR2430

+

3

4

5

6

10

Fixture

The device must be used indoor and has to be installed using the provided mounting bracket. This support can be fixed using screws (recommended). The screws and

dowels are not delivered with the product. They are depending on your wall material. If it is not possible to fix the device with screws, for example when needing to be

fixed on a glass wall, you can use the provided double-sided tape.

⚠ Clean carefully the surface before stucking the tape.

The SLATE106 device is generally fixed by keeping its bottom at 140 cm far from the floor.

Fix the mounting bracket with the right orientation.

1

Counterbores are facing to you (to integrate the screw head)

2

Holes for fixing the SLATE106 are facing downward

Once the mounting bracket is fixed (with some screws or a adhesive tape), place the SLATE106 device face to the mounting bracket. Fix it definitively with the 2 M2.5x25

screws provided using a little slotted screwdriver

3

:

SLATE106 DRILL PATTERN

screws :

55,6 40

33,5

Ø ≤ 4mm

5mm ≤ Ø ≤ 9mm

Ensure that the holes for fixing the SLATE are facing downward

1

2

11

Follow the customer installation plan to install all the other SLATE106 devices.

M2.5x25 screw

3

12

1.5 Batteries

Batteries specifications

The SLATE106 device is designed to work with 4 CR2430 Lithium coin batteries. The battery model has been chosen to obtain the best performances for SLATE106 using.

The batteries features are described below. Use the same reference to obtain the best battery lifetime. However, an equivalent reference may be used.

Type CR2430

Nominal voltage 3V

Typical capacity 290mAh

Chemical system Lithium Manganese Dioxide

Reference 2430/CR2430 VP-1 ENERGIZER LITHIUM [Energizer]

Replacement procedure

⚠ In case of batteries replacement, change the 4 batteries at the same time with the new ones. The batteries must be changed by a qualified people, who is

knowing perfectly the replacement procedure. The batteries must be recycled according to your country’s regulations.

Remove each battery with its holder, using a little slotted screwdriver. Grab and then pull the edge of the plastic holder, remove the old battery from the holder

Insert the new battery with the positive side facing up. Glide the battery with holder into its place using your finger or screwdriver pushing into the plastic of holder

part: you must feel a clip when the battery is installed

Repeat the same operation for the 4 batteries.

Battery energy status (%)

The battery energy status in percent (%) is reported

through the SMH300 hub Web configuration interface. For further information, refer to the SMH300 User manual on the Web site https://www.qeedji.tech.

through the Slate Maintainer mobile application. Refer to the Slate Maintainer application (RFU)

Grab the edge of holder

Pull the holder

to the right

Insert new battery

Glide battery and holder

13

1.6 Pictureframe application

The SLATE106 device embeds the

Pictureframe application which is able to display on the SLATE106 device screen, and in 4 grey levels, a full sceen .ppk picture

(propriety format) which can be updated:

through the USB mass storage (standalone),

by a hub SMH300 , through the WPAN1 and/or

by a key press (Left, Middle, Right).

A

Message Overlay text can be updated by a mobile application (through the WPAN2 ).

Type WPAN link dedicated to BLE type

WPAN1 hub devices BLE (Bluetooth Low Energy)

WPAN2 mobile devices BLE over GATT profile

The SLATE106 device is designed to be most of time in sleep mode, to save power and increase the battery lifetime. It can be woken-up by 3 event types:

When an USB cable is connected or disconnected

When the internal timer has elapsed:

This internal timer is set automically when a new active interval is programmed

The default active interval is:

from 8.00 AM to 7.00 PM

5/7 days: Monday, Tuesday, Wednesday, Thursday, Friday

to change the configuration, refer to the chapter

When a vibration is detected:

The vibration detection can be activated or inactivated according to your needs.

When the vibration detection and the touch key are activated, the pictureframe can send the key pressed value (keycode) to the hub through the WPAN1

☛ Several features can be all activated at the same time

14

1.6.1 Features summary

Picture update with Spe Desktop

The SLATE106 device can be used in Spe Desktop mode. The full screen .ppk picture to display can be generated through the USB mass storage thanks to the

SPE_Desktop tool present on the file system. For further information, refer to the chapter Spe_desktop tool or

Picture update with a picture drop through USB

The full screen .ppk picture to display can be generated through the USB mass storage with a simple *.ppk picture dropped from your MS-Windows computer to your

SLATE106 device. In this case, other .ppk file names than

spe.ppk are supported.

☛ An img2ppk.exe tool is provided to create some .ppk picture from any .PNG or a BMP picture in the 800x600 resolution (for further information, visit the Qeedji

Support Web site

https://www.qeedji.tech)

Picture update when paired to a SMH300 hub

When paired to SMH300 hub, the full screen .ppk picture to display, the application configuration file and the software release are provided by the hub device through

the

WPAN1 .

◬ Do not execute the APPLI.HTA application to configure the SLATE106 device when it is paired to a hub, except to repair a SLATE106 configuration.

◬ To support the Right key press detection for Check Out button and , and Left key press detection for Check In , both the vibration detection and the touch key

detection need to be activated in the

SMH300 hub. For further information, refer to the SMH300 User manual on the Web site https://www.qeedji.tech.

Message Overlay: partial update with a message when paired to a mobile

When paired to a mobile, the Slate Message Overlay mobile application is able to send a message through WPAN2 , which is then displayed in overlay over the full screen

.ppk picture in a predefined area and for a programmable duration (for further information, refer to the chapter

Slate Message Overlay application

Secondary picture: picture update by a key press

Is is possible to display some alternative full screen .ppk pictures by pressing simply a key on the SLATE106 device. For further information, refer to the chapter

Secondary picture display.

System configuration

The Pictureframe application configuration parameters are stored in the configuration file APPLI.CFG . For further information, refer to the chapter APPLI.CFG

configuration file

.

The configuration file

APPLI.CFG can be modified:

through USB mass storage by executing APPLI.HTA . For further information, refer to the chapter APPLI.HTA configuration tool or

through WPAN1 if the device is paired to with a SMH300 hub. For further information, refer to the SMH300 User manual on the Web site https://www.qeedji.tech.

Only the

reset PIN code for WPAN2 (mobile aplication) and the Date & Time can by modified by the Slate Maintainer mobile application. For further information, refer

to the chapter

Slate Maintainer application (RFU).

Application behaviour customization

Once woken-up, the Pictureframe application launch sequence of actions. After these actions have completed, the Pictureframe application returns in sleep state. This

actions sequence can be customized in the

wake-up source versus actions matrix (for further information, refer to the chapter Actions matrix configuration).

◬ Except to activate the secondary picture display feature, it is not recommended to modify this matrix configuration without a Qeedji support validation. Indeed some

matrix combinations values may prevent the SLATE106 to work properly.

15

SPE Desktop

SPE desktop is a simple tool spe.exe , executed directly from the SLATE106 device, offering a graphical interface permitting to enter a rich text and to save it into the

main .ppk picture

spe.ppk .

To make displayed this .ppk picture, ensure that the

Test card is inactivated. For further information, refer to the chapter APPLI.HTA configuration application.

⚠ If this SLATE106 device has been already paired to a hub, you have to make a Restore to factory setting . For further information, refer to File system.

Configuration

Check that your SLATE106 device is ready to use SPE Desktop tool and display its picture:

Plug the SLATE106 device to a MS-Windows computer with an USB cable (micro USB type B to USB) and wait for the USB mass storage is mounted properly

This file, stored at factory, must be present:

spe.exe

If spe.exe is not present on the USB mass storage, download SPE Desktop tool from the Web site www.qeedji.tech. Copy the spe.exe into the USB mass

storage of SLATE106 device.

Configure your SLATE106 device by executing APPLI.HTA

inactivate the testcard

set the appropriate file name. Default spe.ppk , and verify that no hub will change the configuration file. Then, eject properly the USB mass storage.

.ppk picture update with SPE Desktop tool

To save a new .ppk picture with

SPE Desktop tool:

Plug the SLATE106 device to a MS-Windows computer with an USB cable (micro USB type B to USB) and wait for the USB mass storage is mounted properly,

Execute spe.exe directly from the USB mass storage of the SLATE106 device

Type your text like any other text editor (or copy-paste a text with custom fonts),

Change the font size, align your text, change the font type

1

or select font color in grey levels (black, dark grey, light grey)

2

Example:

☛ If you want to edit the current .ppk picture, in the menu File , select Open from Slate

☛ The function Open from Slate can not work with PPK generated with the tool Img2ppk.exe

When finished, in the menu File , select Save to Slate . Your .ppk picture is saved automatically as spe.ppk in the SLATE106 USB mass storage and is

automatically displayed on it,

Eject properly the USB mass storage. The USB mass storage of the SLATE106 device is mounted back again automatically until the USB cable is really unplugged,

Unplug the USB cable.

System files

These are the file present on the file system

APPLI.HTA :

spe.exe

spe.ppk

In case these file are still present, remove them and check again that the SLATE106 device is properly unparied from the

SMH300 hub.

1

2

16

.PAIRED

HUB.PPK

Case sensivity

The pictureframe application is not case sensive. So it makes no difference between a character in lower case (for example: azerty.com ) and the same character in

upper case (for example:

AZERTY.COM )

17

1.6.1.2 Secondary picture display

The secondary image is a feature which allowing to display an alternative .ppk image stored on the SLATE106 device.

This feature is not active by default and need to be activated in the

APPLI.CFG configuration file. Execute from the USB mass storage the application APPLI.HTA .

Activate the support for Wake-up by vibration sensor

Activate the support for Touch keys

Check that the action Display a key image instead of standard one, during seconds for the wake-up source After key .

Duration

Adjust the duration if required (default: 60 seconds). The maximal duration for the secondary picture is 18 hours.

Configuration example

☛ In that use case, it is considered that SLATE106 device is not paired to a SMH300 hub. So, for optimization reasons, all what is action linked to WPAN1 has been

inactivated in the matrix

☛ In that use case, it is considered that the support of the feature Slate Message Overlay is not required for SLATE106 device and has been inactivated. So, for

optimization reasons, all what is action linked to WPAN2 has be inactivated in the matrix

Each time a key configuration file is pressed, the keycode sent is taken in the list in the defined order and the associated secondary .ppk picture is displayed. At the end

of the list, it comes back to the first keycode of the list.

The SLATE106 device supports until 3

Touch keys and is depending on the PSN value.

SLATE106 device PSN value Number of supported key Key supported

PSN00900-XXXXX 2 Left, Right

PSN00901-XXXXX 2 Left, Right

PSN00902-XXXXX 3 Left, Midlle, Right

A list of 8 keycode values can be mapped per key. If there is not keycode value defined for a key, this key is inacivated

So that the display of a secondary .ppk picture can be, a .ppk picture with the appropriate filename must be present on the file system:

For example: F1.ppk , F2.ppk , F3.ppk , .... If there no appropriate .ppk picture in the file system, the secondary .ppk picture can not be displayed.

For each of the 3 keys, several keycodes values can be mapped permitting to displayed consecutively several secondary .ppk picture each time this key is pressed.

Hexa value associated for each image name:

Value (Hexa) Associated filename

1 F1.PPK

18

2 F2.PPK

3 F3.PPK

4 F4.PPK

5 F5.PPK

6 F6.PPK

7 F7.PPK

8 F8.PPK

9 F9.PPK

A F10.PPK

B F11.PPK

C F12.PPK

◬ *The remaining place of the USB storage is defining the max. number of .PPK files (118 KB) that you can store.

Default keymap after factory

One key press on the Left key displays the one

Touch key Keymap signed integer Hexadecimal picture 1 picture 2 picture 3 picture 4 picture 5 picture 6 picture 7 picture 8

Left 268435456 0x10000000 1 (hexa) 0 (hexa) 0 (hexa) 0 (hexa) 0 (hexa) 0 (hexa) 0 (hexa) 0 (hexa)

Middle 536870912 0x20000000 2 (hexa) 0 (hexa) 0 (hexa) 0 (hexa) 0 (hexa) 0 (hexa) 0 (hexa) 0 (hexa)

Right 805306368 0x30000000 3 (hexa) 0 (hexa) 0 (hexa) 0 (hexa) 0 (hexa) 0 (hexa) 0 (hexa) 0 (hexa)

Example of keymap:

Touch key Keymap Signed integer Hexadecimal picture 1 picture 2 picture 3 picture 4 picture 5 picture 6 picture 7 picture 8

Left 1442840576 0x56000000 5 (hexa) 6 (hexa) 0 (hexa) 0 (hexa) 0 (hexa) 0 (hexa) 0 (hexa) 0 (hexa)

Middle 536870912 0x20000000 2 (hexa) 0 (hexa) 0 (hexa) 0 (hexa) 0 (hexa) 0 (hexa) 0 (hexa) 0 (hexa)

Right -1979711488 0x8A000000 8 (hexa) A (hexa) 0 (hexa) 0 (hexa) 0 (hexa) 0 (hexa) 0 (hexa) 0 (hexa)

Example:

For the left key, the keymap is corresponding to F5.PPK, F6.PPK

For the middle key, the keymap is F2.PPK

For the right key, the keymap is F8.PPK, F10.PPK When this key sequence is pressed: [left, middle, right, left, middle, right, left, middle, right], the picture display

order will be [

F5.PPK , F2.PPK , F8.PPK , F6.PPK , F2.PPK , F10.PPK , F5.PPK , F2.PPK , F8.PPK ]

After the timeout, the SLATE106 device is displaying back the full screen main .ppk picture.

☛ When the integer value upper than 2147483647 are not supported. In this case, transform it in negative value by removing to it the value 4294967296.

◬ Fully fill the available space with image F.ppk images may prevent SLATE106 to upgrade its software.

Reserve 220 KB for software upgrade

A minimum available free space of 220 KB is required on the USB storage to warranty the SLATE106 software upgrade.

Optimize free space on the file system

The spe.exe application (109 KB) is present by default on file system. It is used to generate a main full screen .ppk picture (default name : spe.ppk ). When your

spe.ppk is generated and you are sure it you don't need to changed it soon, you can remove this spe.exe file to free up about 109 KB. To restore the spe.exe , you can

download it from the Qeedji Web site

https://www.qeedji.tech.

19

1.6.1.3 Working with a hub

The SLATE106 device can work with a

SMH300 hub. In this case, the picture .PPK is generated by the hub then it is downloaded by the SLATE106 device through WPAN1 .

The

SMH300 hub is able to work with up to 20 SLATE106 devices. A configuration must be done first to pair each SLATE106 device to the SMH300 hub. Each SLATE106

device has an index value, between the

Index valie 1 to 20 . Thanks to this Index , the .ppk picture to be displayed is stored in the SMH300 hub appropriate WebDAV

director (one directory for each SLATE106 device).

WPAN1

The communication between the hub and the SLATE106 devices is done over WPAN1 , BLE 4.1 protocol (Bluetooth Low Energy). Each SLATE106 device makes periodically

some connections with the

SMH300 hub. In case the .ppk picture to display is different from the current one, it downloads immediately the new .ppk picture then

displays it.

The BLE communication is exclusive and implies that the

SMH300 hub can communicate with only one SLATE106 device at a time.

Every 15 minutes (default and minimal period value), the

SMH300 hub starts to communicate with all the paired SLATE106 devices the one after the other, starting with

device paired with the

Index value: 1 , and ending with device paired with Index value: 20 .

Pairing

To pair the SLATE106 device to a SMH300 hub, connect to the Web configuration interface of the SMH300 hub and Activate the pairing process. For further information

about the pairing process with the

SMH300 hub or configration modification, refer to the SMH300 User manual on the Web site https://www.qeedji.tech.

By default, the SLATE106 device is configured to wake-up every 15 minutes. And the

Test card is displayed.

So, wait for max. 15 minutes until the device is waking-up and is automatically detected by the SMH300 hub and the pairing process is finalized.

☛ It is possible to not wait 15 minutes by forcing a SLATE106 device wake-up by plugging for 3 seconds a USB power bank (or to a labtop having an USB 2.0

connector)

☛ In case issue to complete the pairing configuration, ensure with the

APPLI.HTA (application for SLATE106) that the keycode Receive Message Overlay over WPAN1

is unchecked.

Test card removing

To be able to display a .ppk picture other than the Test card content, the Test card needs to be inactivated in the SMH300 hub Web configuration interface. For

further information, refer to the

SMH300 User manual on the Web site https://www.qeedji.tech.

☛ The SLATE106 device has to wake up to be able to take a new configuration (add, modifiy or remove the PIN code , add or remove the Test card , change the

hostname)

When the TestCard is disappearing, do consider that the SLATE106 device is paired to the hub and is ready to update its .ppk picture.

SMH300 WebDAV directory .ppk picture update

Each time the .ppk picture of the appropriate SMH300 hub WebDAV directory http://<SMH300_IP_Addr>/.output/n/ is updated, the SLATE106 device should display the

new .ppk picture is less than 15 minutes after (in default heartbeat value configuration).

☛ Some applications running with the SMH300 hub allows to update the .ppk picture of the appropriate SMH300 WebDAV directory

http://<SMH300_IP_Addr>/.output/n/ . For further information, refer to the SMH300 User manual on the Web site https://www.qeedji.tech.

☛ To save battery energy, the .ppk picture is only updated when the new

HUB.PPK picture is different. If the SMH300 hub WebDAV directory

http://<SMH300_IP_Addr>/.output/n/ is empty or the .ppk picture (default name : HUB.PPK ) has not been updated, the SLATE106 device can not update its .ppk

picture. In case issue, check first that the

Index associated to your SLATE106 device is correct.

.ppk update time

When the communication between the SLATE106 device and the SMH300 hub is very difficult, the .ppk picture downloading time for a new .ppk picture is lower than 10

seconds. This duration is used to compute the .ppk picture downloading success rate.

System files

When the pairing is successful, and the .ppk picture updated, these files are available on the USB mass storage:

.PAIRED : present if the device is paired (or has been already paired) to a SMH300 hub

HUB.PPK : .ppk picture to display (propriety format) when TestCard is not inactivated. Default file name: HUB.PPK . This file name can be modified.

APPLI.CFG : When the SLATE106 device is paired to a SMH300 hub, it inherits of the configuration file provided by the SMH300 hub. So, in this case, do not modify

this file from the USB mass storage.

APPLI.HTA : application allowing to edit and save parameters in APPLI.CFG file. When the SLATE106 device is paired to a SMH300 hub, it inherits of the

configuration file provided by the SMH300 hub. So, in this case, do not execute this application from the USB mass storage.

20

Page is loading ...

Qeedji SLATE Series User manual

This manual is also suitable for

Qeedji SLATE Series User manual

Other documents