Bushnell Aggressor 119873C User manual

Brand: Bushnell

Model: Aggressor 119873C

Type: User manual

Model#: 119873C

INSTRUCTION MANUAL

11-15

IMPORTANT NOTE

Congratulations on your purchase of one of the best trail cameras on

the market! Bushnell is very proud of this little unit and we are sure you

will be pleased with it as well. We appreciate your business and want to

earn your trust. Please refer to the notes below and the instructions in

this manual to ensure that you are completely satisﬁed with this product.

If your Bushnell Trophy Cam HD Aggressor does not seem to be

functioning properly or if you are having photo/video quality issues,

please check the Troubleshooting/FAQ section on pages 31-35.

Problems are often due to something simple that was overlooked,

or require only changing one setting to solve.

If your problem continues after trying the solutions in the

Troubleshooting/FAQ section, please call Bushnell Customer

Service at (800) 423-3537. In Canada, call (800) 361-5702.

Bushnell recommends using a full set of eight Energizer® Lithium

AA batteries in these Trophy Cam HD Aggressor models to obtain

maximum battery life

Do not mix old and new batteries

Do not mix battery types-use ALL lithium or ALL alkaline

Bushnell recommends using SanDisk® class 6 or faster SDHC

Cards (up to 32GB capacity) in your Trophy Cam HD Aggressor

INTRODUCTION

About the Trophy Cam HD Aggressor

The Bushnell Trophy Cam HD Aggressor is a digital scouting camera. It can be

triggered by any movement of game in a location, detected by a highly sensitive

Passive Infra-Red (PIR) motion sensor, and then take high quality pictures (up to

14MP still photos), or video clips.

The Trophy Cam HD Aggressor consumes very little power (less than 0.25 mA) in

a stand-by (surveillance) state. This means it can deliver up to six months stand-by

operation time when the device is powered by the full capacity of AA alkaline batteries,

and up to twelve months utilizing lithium AA batteries. Once motion in the monitored

area is detected, the digital camera unit will be triggered at once (typically within

one second) and then automatically take photos or videos according to previously

programmed settings. The Trophy Cam HD Aggressor is equipped with built-in

infrared LEDs that function as a ﬂash, so that it delivers clear photos or videos (in

black & white) even in the dark, and it can take color photos or videos under sufﬁcient

daylight. The Trophy Cam HD Aggressor HD is designed for outdoor use and is

resistant against water and snow.

Your trail camera is one of the latest generation of Bushnell Trophy Cam HD

Aggressor HDs, and includes many new or improved features, including:

• Auto PIR Sensitivity-the camera monitors ambient temperature conditions and

automatically adjusts the sensor/trigger signal to be more sensitive to slight

variations in temperature on hot days, less sensitive on cold days.

• Hyper NightVision-The IR LED Flash array now has increased range, brighter

output and better coverage for improved nighttime images.

• Field Scan 2x with Live Trigger-This “time lapse” feature includes the option

for a second block of recording with its own start/stop times. Trigger signals

generated by nearby wildlife activity will still generate additional photos/videos

as they normally would, independently of the Field Scan operation.

• GPS Geotag Capability-allows the user to input the longitude and latitude of

the camera’s position, which will be embedded in each photo ﬁle. This enables

Google Earth, Picassa and other geotag enabled software to automatically

show a map pinpointing each camera’s location when a group of photos are

reviewed on a computer. Especially useful for those who setup multiple Trophy

Cam HD Aggressors to monitor large or widely separated areas.

• Multi Flash Mode (LED Control)- prevents overexposed ﬂash photos in close

range applications

• Hybrid Capture Mode-allows both still photos and videos to be captured at each

trigger, up to highest resolution settings for each.

• NV Shutter-user can select shutter speed for images captured at night allowing

control over brightness vs. ability to stop motion

• Camera Operating Mode can be limited to Day only, Night only, or 24 HRs

And many more features such as 1080p HD Video with Audio, 0.2 second trigger

speed and 1 second recovery time (still photos), widescreen or fullscreen format

still photos, imprintable camera name (user set) along with current data including

temperature and moon phase.

Applications

The Trophy Cam HD Aggressor can be used as a trail camera for hunting or

scouting game. It is also suitable for surveillance usage.

PARTS AND CONTROLS

The Trophy Cam HD Aggressor provides the following connections for external

devices: USB port, SD card slot and external DC power in (pg 7, Fig. 1).

A 3-way power switch is used to select the main operating modes: OFF, SETUP,

and ON (pg 7, Fig. 2).

A control key interface with six keys is primarily used in SETUP mode to select

operational functions and parameters. As shown on the next page, these keys are: UP,

DOWN, LEFT, RIGHT, OK and MENU. Three of the keys can also perform a second

function (shortcut operations in SETUP mode) in addition to their main function: The

DOWN key can be used to set the camera to Photo mode (still camera icon), and

the UP key can set the camera to Video mode (movie camera icon). The RIGHT key

also serves as the manual shutter (“SHOT”) button of the camera. These secondary

functions are indicated by icons or text above the key as shown on the next page.

INSIDE VIEW

Fig. 2: Button and

Switch Guide

Fig. 1: Connections

FRONT VIEW

LED IR

Flash

Motion/ Low

Battery Indicator

Lens

Lock

Hole

PIR

Sensor Latch

Light

Sensor

ARD

SETUP

OFF

LCD Screen

Power/Mode

Switch

UP/Video

DOWN/Photo

LEFT

RIGHT/Shot

Cable to Battery

Compartment

Tripod Socket

DC in

Cover Plug

Video Mic

USB Port

SD Card Slot

DC In

Video Mic

INSTALLING THE BATTERIES AND SD CARD

Before you begin learning how to use your Trophy Cam HD Aggressor, you will ﬁrst

need to install a set of batteries and insert an SD card. Although that may only take

you a minute, there are some important notes about both batteries and SD cards you

should be aware of, so please take the time to read the following directions and

cautions:

Loading Batteries

After opening the two latches on the right side of the Trophy Cam

HD Aggressor, you will see that the Trophy Cam HD Aggressor

has eight battery slots. For maximum battery life, you should install

a full set of batteries. The Trophy Cam HD Aggressor may also

be operated by just four batteries installed in the ﬁrst slots only

(starting on the top or left-see photos). Battery life will be shorter

with 4 batteries, but the camera will operate normally. Whether you

use 4 or a full set, be sure to insert each battery with correct polarity

(negative or “ﬂat” end against the long spring of each battery slot).

Bushnell recommends using a full set of new lithium AA (Energizer®

brand) or alkaline AA batteries. NiMh Rechargeable batteries are not recommended,

as the lower voltage they produce can cause operational issues.

You can also connect an optional Solar Panel accessory (model# 119756C -please

visit www.bushnell.com for more information) to the “DC In” jack at the bottom of the

Trophy Cam HD Aggressor (other external power supplies should not be used, as

the camera and/or display may not function correctly). If the solar panel is connected

and AA batteries are installed, the Trophy Cam HD Aggressor will be powered by

the solar panel's rechargeable lith-ion battery, as long as it provides adequate voltage

(if not, the camera will switch to battery power). The solar panel's battery will power

the camera at night.

When the batteries become weak (or a device with insufﬁcient power is connected

to DC In), the low-battery indicator LED will glow blue, indicating the batteries should

be changed (pg 7, Front View).

Inserting the SD Card

The Trophy Cam HD Aggressor has 32MB of internal memory, which can hold only

about 18 photos (@ 8MP resolution). This is handy for testing and getting familiar

with the camera, but you will no doubt want to leave the camera unattended for longer

than a day, so using an SD card is recommended for all models. Insert the SD card

(with the camera’s power switch in the OFF position) before beginning to operate

the camera. Don’t insert or remove the SD card when the power switch is in the ON

position.

The Trophy Cam HD Aggressor uses a standard SD (Secure Digital) memory

card to save photos (in .jpg format) and/or videos (in .avi format). SD and SDHC

(High Capacity) cards up to a maximum 32GB capacity are supported. Using high

speed SD cards (SanDisk® SDHC rated class 6 or higher) is recommended if you will

use the 1280x720 or 1920x1080 HD video settings. Before inserting the SD card

into the card slot after opening the camera’s front cover, please make sure that the

write-protect switch on the side of the card is “off” (NOT in the “Lock” position). The

following describes how to insert and remove the SD card:

• Insert the SD card into the card slot with its label side upwards (see below). A

“click” sound indicates that the card is installed successfully. If the wrong side

of the card is facing up, you will not be able to insert it without force-there is

only one correct way to insert cards. If the SD card is not installed correctly,

the device will not display an SD card icon on the LCD in SETUP mode (the

SD card icon displayed after switching to SETUP mode will have a “lock” symbol

inside it in it if the card is locked). Formatting the SD card by using the Trophy

Cam HD Aggressor’s “Format” parameter before using it for the ﬁrst time is

recommended, especially when a card has been used in other devices (see pg.

23, “Format” for details).

• To take out the SD card, just gently push

in the card (do not try to pull it out without

pushing in ﬁrst). The card is released from the

slot and ready to be removed when you hear

the click. WARNING: Be sure the camera’s power is switched OFF

before inserting or removing SD cards or batteries.

USING THE Trophy Cam HD Aggressor

Once you’ve prepared your Trophy Cam HD Aggressor by properly installing

batteries and an SD card, you could simply take it outside, strap it to a tree, switch it

on and leave-and you might get some great photos that are exactly what you wanted.

However, we highly recommend that you ﬁrst spend some additional time indoors with

this manual and your camera until you know a bit more about what the 3-way switch

and those control keys do. If nothing else, you’ll probably want to at least set the date

and time so the camera will imprint them (or not-it’s your option) on your photos as

they are taken, learn how to set the camera to shoot video clips instead of still photos

if you like, and read some tips about mounting it on a tree.

THE OFF, ON, AND SETUP MODES

The Trophy Cam HD Aggressor has three basic operational modes:

• OFF mode: Power switch in the OFF position.

• ON mode: Power switch in the ON position (LCD screen is off.)

• SETUP mode: Power switch at SETUP position (LCD screen is on).

OFF MODE

The OFF mode is the “safe” mode when any actions must be taken, e.g., replacing

the SD card or batteries, or transporting the device. You will also use OFF mode if

you connect the camera to a computer’s USB port later to download your photos/

videos. And of course, when you are storing or not using the camera, you will switch it

to OFF. Please note that even in the OFF mode the Trophy Cam HD Aggressor still

consumes power at a very low level. Therefore, it’s a good idea to take the batteries

out of the battery compartment if the camera will not be used for a long time.

ON MODE

Anytime after the batteries and SD card have been inserted, you can switch on the

camera. When the power switch is moved to the top position, the camera will enter

into the ON (Live) mode. The motion indicator LED (pg. 7, “Front View”) will blink

red for about 10 seconds. This interval allows time for you to close the Trophy Cam

HD Aggressor’s front cover, lock it, and leave the monitored area. Once in the ON

mode, no manual controls are needed or possible (the control keys have no effect).

The Trophy Cam HD Aggressor will take photos or videos automatically (according

to its current parameter settings) when it is triggered by the PIR sensor’s detection of

activity in the area it covers.

You can either move the power switch directly from OFF to ON mode, or stop at the

SETUP position ﬁrst to change one or more settings, then move the switch to ON

after you have ﬁnished doing so.

SETUP MODE

In the SETUP mode you can check and change the settings of the Trophy Cam

HD Aggressor with the help of its built-in LCD. These settings, found in the SETUP

Menu, let you change the photo or video resolution, interval between photos, switch

the time imprint on, etc. Moving the power switch to the SETUP position will turn on

the LCD display, and you will see an information screen that shows how many images

have been taken, the battery level, camera or video mode, etc (Fig. 3, next page).

NOTE: Always move the power switch from OFF to SETUP mode. It is possible

that the camera could lockup if it is switched from ON to SETUP mode. If this

occurs, simply move the switch to OFF and then push it up to SETUP again.

SETUP Mode Shortcut Keys/Functions

As mentioned earlier in “Parts & Controls”, four of the keys below the LCD

have secondary, “shortcut” functions when the camera is switched to SETUP mode

(but the MENU key has not been pressed):

• Press the UP key to quickly set the camera to shoot video clips.

• Press the DOWN key to quickly set the camera to take still photos.

• Press the RIGHT key to manually trigger the shutter. This is useful for testing the

camera-make sure you are in SETUP mode, press the RIGHT key, and a few

seconds later a photo or video (depending on how the camera was set) will be

saved to the SD card (or internal memory if no card is inserted). The “number of

images taken” counter on the bottom left of the LCD will increase by one. If the

display indicates “SD PROTECTED” when you press the SHOT key, switch the

camera OFF, remove the SD card and slide its protect switch off.

Fig. 3: SETUP Information Screen

Still Photo Mode

Time Stamp

Field Scan On

# of Photos Taken Remaining Photo Capacity

Date:Month-Day-Year

Battery Level

Image Size (Resolution) SD Card Status

Time

Hour:Minute:Second

Camera (Still Photo) Mode

Video Mode

Video Sound On Video Resolution

Available Video Recording Time

Video Mode

USING THE SETUP MENU TO CHANGE SETTINGS

The main purpose of the SETUP mode is to allow you to change the settings of

the camera’s parameters (19 different ones are available!) so your Trophy Cam HD

Aggressor operates exactly the way you want it to. You will do this by entering the

SETUP Menu and pressing the keys below the LCD display, which will show you

each parameter and its setting.

Changing Parameter Settings in SETUP Mode

A wide range of options or “parameters” are provided to allow you to set the Trophy

Cam HD Aggressor to your operational preferences. To change the setting of

any parameter you must ﬁrst switch to the SETUP mode. Once in SETUP mode,

pressing the MENU button will allow you to select any parameter and change its

setting. The name of the parameter and its current setting will be shown on the LCD.

Pressing the RIGHT or LEFT key scrolls to the next or previous parameter (RIGHT

key to move on to the next parameter and LEFT key to go back to the previous

parameter), and pressing the UP or DOWN key lets you select a different setting

for the currently displayed parameter. Once you have selected your preferred new

setting for a parameter, press the OK button to save the new setting (actually change

it). When you are ﬁnished changing the settings of one or more parameters, press

MENU again to exit the SETUP menu. MENU can also be pressed anytime you

want to cancel changing a parameter’s setting after a new setting has been selected

(but OK has not been pressed yet). After setting the parameters to your preferences,

be sure to move the switch to ON to begin actually taking photos or videos. No

images will be captured if the switch is left in the SETUP position (unless you press the

RIGHT/Shot key after exiting the menu)-in fact, the camera will power off automatically

after a few minutes with no key pressed.

Parameter Settings Display

The settings for each parameter are shown on the display screen of your Trophy

Cam HD Aggressor. Only one setting is displayed at a time, starting with the current

setting for the parameter when it is ﬁrst selected (pg. 14, Fig. 4a). To change the

setting, use the UP/DOWN keys to display the new setting you want (Fig. 4b), then

press OK to “Execute” (make the actual change to this setting). If you want to conﬁrm

this setting is now the current one, just press the RIGHT key to scroll to the next

parameter, then press LEFT to go back again to the previous one. You should see the

parameter setting you just made.

Fig. 4: Selecting Parameter Settings

(4a)

(4b)

Press MENU

Press DOWN

Press OK

EXAMPLES-Changing the Settings of Some Common Parameters

Following this page, you will ﬁnd tables listing all of the parameters found in the

SETUP Menu, along with their possible settings (or range of settings), and a detailed

description of what the parameter controls and what the settings do. If you read the

previous section detailing how to select parameters and change their settings, you

should be able to dive right in, ﬁnd the parameter(s) you want, and setup the camera

to suit your preferences. But maybe you’d rather walk through an example or two ﬁrst:

To change any parameter’s setting, always start with the power switch in the SETUP

position. After the LCD comes on, press the MENU key.

The ﬁrst parameter you will see when you ﬁrst enter the SETUP Menu is “Mode”.

To change it from its default setting of “Camera” (still photos) to “Video” (shoot

video clips), press the DOWN key to select the “Video” setting. Press the OK key to

“Execute” (Set) the new setting you’ve selected for this parameter.

Now press the RIGHT key to move to another parameter in the Menu. Pressing it

three times will take you to “Capture Number”. Try using the UP and DOWN keys

to scroll through the range of settings, then press OK to lock in your setting for the

number of photos the camera takes each time it's triggered.

Pressing the RIGHT key until you reach the last menu item, you'll see the “Default

Set” parameter. Highlight or select “Execute” (using UP or DOWN) and press OK to

restore all parameters (including the Mode and Video Length parameters you changed

a minute ago) back to their original factory default settings. The default settings for

each parameter are indicated in bold type in the SETUP Menu tables on the next

several pages.

Be sure to set the current date and time, using the “Set Clock” parameter, if you

choose to change the “Time Stamp” parameter setting to “On” since that will tell the

camera to imprint the date and time on each of the images it captures.

Field Scan 2x with Live Trigger Feature

Field Scan is a revolutionary new feature for the Bushnell Trophy Cam HD

Aggressor, which allows you to monitor your food plots or ﬁeld edges with time lapse

images or video. When set to “On”, the Trophy Cam HD Aggressor will take a photo

(or record a video clip) automatically at your choice of intervals (for example, once

every ﬁve minutes) during one or two blocks of time you set up for each day, without

requiring a trigger from an active animal. This has the advantage of giving you

the ability to monitor the edge of a ﬁeld that might be 50 or 150 yards away from the

camera out of the PIR sensor’s range. The result is an effective range much greater

than it would normally be, with the camera dependant on triggers generated by nearby

animals. This is a great tool for hunters to scout an entire ﬁeld with only one camera.

If an animal does enter the area covered by the PIR sensor and generate a trigger

event during a time in between the Field Scan intervals you set, the camera will capture

an image or video just as it normally would, based on your other menu settings. Here’s

how to setup and use Field Scan (be sure you’ve set the current time in “Set Clock”

ﬁrst, so your Field Scan recording will stop and start at the correct times of day):

1. Move the main switch to SETUP, then press MENU.

2. Keep pressing the RIGHT key, stepping through the Setup Menu until you reach

Field Scan.

3. Press the UP key to select On, and press OK (Step 1, pg.18). You will see "A",

representing the ﬁrst block of time you can deﬁne (a second block of time later

in the day, "B" can also be setup if you wish). Press OK (Step 2). This takes

you to the screen to set Start and Stop times, which determines the clock times

when the ﬁrst block of Field Scan recording will begin and end for each day.

You can set these times to the exact hour and minute you want, for a recording

“window” that lasts anywhere from just a minute to a full 24 hours.

4. Set the [Start] and [Stop] times, beginning with the Start hour, using the UP/

DOWN keys to change the setting (Step 3). The hour setting is based on a 24-

hour clock, with “00” hours = midnight, “12” hours = noon, “23” hrs = 11PM,

etc. To move to the next setting, press the RIGHT key, change the minute for

the Start time with UP/DOWN, then on to the hour and minute settings for the

Stop time.

5. After you ﬁnish setting the Stop minutes, press OK to conﬁrm your settings for

the ﬁrst block of Field Scan recording. If desired, you can create a second block

of time by pressing the DOWN key to select "B" (Step 4), then press OK and

follow the same process to set Start and Stop times for Field Scan block "B"

(Step 5). As an example of how you might use these two available time blocks,

you could setup Field Scan time block "A" for the dawn hours from 6 AM to 8

AM, and block "B" to capture images between 5:30 and 7 PM. No Field Scan

recording would occur from 8AM to 5:30PM, or from 7PM to 6AM.

6. After setting Start/Stop times to deﬁne Field Scan block "A" and/or "B", press

OK, then press the UP or DOWN key to select "Interval" and press OK (Step

6). The Field Scan "Interval" setting lets you control how often a photo or video

clip is recorded during the block(s) of time you deﬁned with the Start and Stop

settings. Your options are 60 minutes, 30 minutes, 15 minutes, 5 minutes (this

is the default), or 1 minute (still photo mode only). Use the UP/DOWN keys to

select your preference, then press OK to save it (Step 7). Note that for videos,

"Interval" is independent of the Length of each video recording-it’s how often

videos are recorded, not how long each one lasts.

7. Here’s an example of how the camera would operate, based on the following

Field Scan settings:

Field Scan: On

Field Scan A:

[Start]: 6:00

[Stop]: 8:00

Field Scan B:

[Start]: 17:30

[Stop]: 19:00

Interval: 15M

These settings would cause the camera to capture a photo (or video, if the

camera is set to that mode) once every 15 minutes, beginning at 6 AM, until the

Field Scan "A" recording block stops at 8:00 AM. Later that day, the camera

would again take a photo or video every 15 minutes between 5:30 PM and

7:00 PM (during Field Scan time block "B"). The next day, the camera would

again record an image or video once every 15 minutes between 6:00 and 8:00

AM, and between 5:30 and 7:00 PM. No Field Scan recording would occur

from 8AM to 5:30PM, or from 7PM to 6AM. Remember, Field Scan recording

is independent of normal triggers due to animal activity–even if no animals enter

the IR sensor coverage zone, an image or video will still be captured every 15

Note: avoid any "overlap" of Field Scan A & B

recording blocks when setting their start and stop

times, to assure correct operation. Also-if the "Camera

Mode" menu parameter is set to "Day" or "Night"

operation only, that will take priority over your Field

Scan settings. Set the Camera Model to "24 HR" if

you are setting both day and night start and/or stop

times in Field Scan.

minutes during the block(s) of time. If an animal triggers the camera “in between”

the 15 minute intervals, it will be recorded.

Note: Field Scan settings of frequent intervals and/or long periods between

start and stop time can reduce battery life.

(Step 1)-set Field

Scan Mode to “On”

(Step 2)-select Field

Scan "A" (press OK)

(Step 3)-set Field

Scan "A" Stop & Start

(Step 4) (opt)-select Field

Scan "B" (press OK)

(Step 5) (opt)-set Field

Scan "B" Stop & Start

Steps 4 & 5 are

optional (only

required if you want

to set up a second

block of Field Scan

recording with

different stop and

start times)

(Step 6)-select Field

Scan "Interval"

(Step 7)-set Field

Scan Interval

Note: the Interval

Setting sets the

timing between each

image for both Field

Scan "A" and "B"

recording blocks.

Parameter Settings

(Bold=default)

Description

Mode Camera, Video,

Hybrid

Selects whether still photos or video clips are

captured when the camera is triggered. Hybrid

mode combines both Camera and Video, so a

still photo and a video clip are both captured for

each trigger.

Image Size

(only aects

still photos

in Camera or

Hybrid modes)

3M Pixel,

8M Pixel,

14M Pixel

Selects resolution for still photos from 3 to 14

megapixels. Higher resolution produces better

quality photos, but creates larger ﬁles that take

up more of the SD card capacity (ﬁlls up faster).

8M is a good compromise between quality and

ﬁle size.

Image Format

(only aects still

photos-

format for video

is tied to Video

Size)

Full Screen,

Wide Screen

Selects 4:3 (Fullscreen, like old TV sets) or 16:9

(Widescreen, like new ﬂat TVs) “aspect ratio”

for still photos. If you like to view your photos on

a TV set or computer monitor, you can set the

format to match it.

Capture

Number

(only aects

still photos

in Camera or

Hybrid modes)

1 Photo,

2 Photo,

3 Photo

Selects how many photos are taken in sequence

per trigger in Camera mode. This setting affects

photos taken in Field Scan mode as well (to

snap two photos every 10 minutes, for example).

Note: only one photo will be captured if "Interval"

is set to 1 second, regardless of the Capture

Number setting. Please also refer to the Interval

parameter.

The SETUP Menu – Parameters and Settings List

w/Descriptions

Parameter Settings

(Bold=default)

Description

LED Control

(Multi-Flash

feature)

Low, Medium,

High

Controls how many LED lamps ﬁre when images

are taken in low light. “High”= all 36 LEDs ﬁre,

which is the default setting. Set to Medium or

Low if you are getting overexposed ﬂash photos

or will place the camera at very close range to

the subject you want to photograph. In general,

select High if most of your intended subjects will

be over 30 ft. from the camera, Medium for the

15 to 30 ft. range, and Low for subjects under

15 ft. away. Note: in video mode, set to LED

Control to “Low” if videos are overexposed at

the Medium setting. At the High setting, videos

at night are limited to 15 seconds maximum

length to prevent overheating.

Camera Name (Input)

See "Using the

Setup Menu Input

Screens"

Allows the user to set a custom name for the

camera. Useful for ID purposes when multiple

cameras are setup, since each camera will

imprint its name on all photos (but not videos) it

captures.

Video Size

(only aects

video clips in

Video or Hybrid

modes)

1920x1080,

1280x720,

640x360

Selects video resolution (in pixels per frame).

Higher resolution produces better quality videos,

but creates larger ﬁles that take up more of the

SD card capacity (ﬁlls up faster). 640x360 is

VGA video in "widescreen" 16:9 format. The

highest setting provides HD video. Using high

speed SD cards (SanDisk® SDHC class 6

or higher) is recommended if you will use the

1280x720 or 1920x1080 video settings.

Page is loading ...

Bushnell Aggressor 119873C User manual

Bushnell Aggressor 119873C User manual

Bushnell Aggressor 119873C User manual

Related papers

Other documents