WAGO Application "Cloud Building Operation and Control" User manual

Brand: WAGO

Model: Application "Cloud Building Operation and Control"

Type: User manual

Product manual | Version 1.0.1

WAGO Cloud

Application “WAGO Cloud Building Operation and Control”

Legal Information

WAGO Kontakttechnik GmbH & Co. KG

Hansastraße 27

D - 32423 Minden

Phone: +49 571/887 – 0

Fax: +49 571/887 – 844169

E-Mail: * [email protected]

Internet: ü www.wago.com

Technical Support

Phone: +49 571/887 – 44555

Fax: +49 571/887 – 844555

E-Mail: * [email protected]

Every conceivable measure has been taken to ensure the accuracy and completeness of

this documentation. However, as errors can never be fully excluded, we always appreci-

ate any information or suggestions for improving the documentation.

E-Mail: * [email protected]

We wish to point out that the software and hardware terms as well as the trademarks of

companies used and/or mentioned in the present manual are generally protected by

trademark or patent.

WAGO is a registered trademark of WAGO Verwaltungsgesellschaft mbH.

Product manual | Version: 1.0.1

Application “WAGO Cloud Building Operation and Control”

Table of Contents

Product manual | Version: 1.0.1 iii

Application “WAGO Cloud Building Operation and Control”

Table of Contents

1Terms ................................................................................................................................4

1.1 Intended Use........................................................................................................... 4

1.2 Typographical Conventions..................................................................................... 5

1.3 Legal Information .................................................................................................... 7

2Security.............................................................................................................................8

2.1 General Safety Regulations .................................................................................... 8

2.2 Indirect Safety ......................................................................................................... 8

3Overview ...........................................................................................................................9

4Requirements .................................................................................................................10

4.1 Activation............................................................................................................... 10

5Starting............................................................................................................................11

5.1 Start the Application .............................................................................................. 11

5.2 Launch the Application.......................................................................................... 11

5.3 Import Required Information ................................................................................. 11

5.3.1 Import Excel File for the First Time ..............................................................13

5.3.2 Import Excel File Again ................................................................................14

6Graphical User Interface ...............................................................................................15

6.1 “WAGO Cloud Building Operation and Control” Application ................................. 15

6.1.1 Side Menu .................................................................................................... 16

6.1.2 Action Area...................................................................................................17

6.1.2.1 Action Area – Complete View..............................................................19

6.1.2.1.1 Menu Bar ................................................................................... 19

6.1.2.1.2 Subareas ................................................................................... 19

6.1.2.2 Action Area – Detail View ....................................................................23

6.1.2.2.1 Menu Bar ................................................................................... 23

6.1.2.2.2 Subareas ................................................................................... 23

7Operating ........................................................................................................................33

7.1 Create New Key Performance Indicator................................................................ 33

7.2 Edit or Delete Existing Key Performance Indicator ............................................... 34

8Appendix.........................................................................................................................36

8.1 Protected Rights.................................................................................................... 36

Terms

4 Product manual | Version: 1.0.1

Application “WAGO Cloud Building Operation and Control”

1Terms

This documentation applies to:

Application “WAGO Cloud Building Operation and Control” in conjunction with a WAGO

PFC Series Controller.

Note

Observe the applicable documentation!

This documentation is part of the complete Instructions for use for the application “WAGO

Cloud Building Operation and Control”. The product may only be operated in accordance

with the complete Instructions for use. Knowledge of the complete Instructions for use is

a precondition for intended use.

1. Read the Product Manual WAGO Cloud.

2. Carefully read the Product Manual.

3. To the extent that you have expanded the WAGO Cloud to include specific applica-

tions: Read the Product manuals of the products used.

Table1: Scope of Applicability – Versions

VersionApplication “WAGO Cloud Building Opera-

tion and Control”

Documentation Version

1.0.0 1.0.0

Besides this documentation, the following supplementary documents are available:

•& Quick Start Guide WAGO Cloud

•& Quick Start Guide WAGO Cloud Application “Dashboards”

All the documentation is available at: üwww.wago.com/cloud.

1.1 Intended Use

WAGO Cloud is a universal IoT solution for machines, systems and buildings for:

• Centralized Collection and Analysis of Data

• Monitoring and managing devices, including your data (e.g, WAGO controllers)

• Visualizing and comparing machines and system data

• Remote access to local configurations and visualizations

• User and group management

Improper Use

Improper use of the products is not permitted. Specifically, improper use occurs in the fol-

lowing cases:

• Non-observance of the intended use

• Use of the products in areas with special risk that require flawless continuous operation

and in which failure or operation of the software can result in an imminent risk to life,

limb or health or cause serious damage to property or the environment (such as the

operation of nuclear power plants, weapon systems , aircraft and motor vehicles)

Terms

Product manual | Version: 1.0.1 5

Application “WAGO Cloud Building Operation and Control”

Warranty and Liability

The terms set forth in the General Business & Contract Conditions for Delivery and Ser-

vice of WAGO Kontakttechnik GmbH & Co. KG and the terms for software products and

products with integrated software stated in the WAGO Software License Contract – both

available at üwww.wago.com – shall apply. In particular, the warranty is void if:

• The products are used improperly.

• The deficiency (hardware and software configurations) is due to special instructions.

• Modifications to the hardware or software have been made by the user or third parties

that are not described in this documentation and that has contributed to the fault.

Individual agreements always have priority.

Obligations of Installers/Operators

The installers and operators bear responsibility for the safety of an installation or a sys-

tem assembled with the products. The installer/operator is responsible for proper installa-

tion and safety of the system. All laws, standards, guidelines, local regulations and ac-

cepted technology standards and practices applicable at the time of installation, and the

instructions in the the products’ Instructions for Use, must be complied with. In addition,

the Installation regulations specified by Approvals must be observed. In the event of non-

compliance, the products may not be operated within the scope of the approval.

1.2 Typographical Conventions

Number Notation

100 Decimals: Normal notation

0x64 Hexadecimals: C-notation

‘100’

‘0110.0100’

Binary: In single quotation marks

Nibbles separated by a period

Text Formatting

italic Names of paths or files

bold Menu items, entry or selection fields, emphasis

Code Sections of program code

> Selection of a menu point from a menu

“Value” Value entries

[F5] Identification of buttons or keys

Cross References / Links

Cross references/links to a topic in a document

Cross references / links to a separate document

Cross references / links to a website

Cross references / links to an email address

Action Instructions

üThis symbol identifies a precondition.

1. Action step

Terms

6 Product manual | Version: 1.0.1

Application “WAGO Cloud Building Operation and Control”

2. Action step

ðThis symbol identifies an intermediate result.

ðThis symbol identifies the result of an action.

Lists

• Lists, first level

– Lists, second level

Figures

Figures in this documentation are for better understanding and may differ from the actual

product design.

Notes

DANGER

Type and source of hazard

Possible consequences of hazard that also include death or irreversible injury

• Action step to reduce risk

WARNING

Type and source of hazard

Possible consequences of hazard that also include severe injury

• Action step to reduce risk

CAUTION

Type and source of hazard

Possible consequences of hazard that include at least slight injury

• Action step to reduce risk

NOTICE

Type and source of malfunction (property damage only)

Possible malfunctions that may restrict the product’s scope of functions or ergonomics,

but do not lead to foreseeable risks to persons

• Action step to reduce risk

Note

Notes and information

Indicates information, clarifications, recommendations, referrals, etc.

Terms

Product manual | Version: 1.0.1 7

Application “WAGO Cloud Building Operation and Control”

1.3 Legal Information

Intellectual Property

Unless barred by applicable legal provisions, unauthorized copying and distribution of this

document, as well as the use and communication of its content are strictly prohibited un-

less expressly authorized by prior agreement. Third-party products are always mentioned

without any reference to patent rights. WAGO Kontakttechnik GmbH & Co. KG, or for

third-party products, their manufacturer, retain all rights regarding patent, utility model or

design registration.

Third-party trademarks are referred to in the product documentation. The “®” and “TM”

symbols are omitted hereinafter. The trademarks are listed in the Appendix (8Protected

Rights [}36]).

Subject to Change

The instructions, guidelines, standards, etc., in this manual correspond to state of the art

at the time the documentation was created and are not subject to updating service. The

installer and operator bear sole responsibility to ensure they are complied with in their

currently applicable form. WAGO Kontakttechnik GmbH & Co. KG retains the right to

carry out technical changes and improvements of the products and the data, specifica-

tions and illustrations of this manual. All claims for change or improvement of products

that have already been delivered – excepting change or improvement performed under

guarantee agreement – are excluded.

Security

8 Product manual | Version: 1.0.1

Application “WAGO Cloud Building Operation and Control”

2Security

2.1 General Safety Regulations

• This documentation is part of the product. Therefore, retain the documentation during

the entire service life of the product. Pass on the documentation to any subsequent

user of the product. In addition, ensure that any supplement to this documentation is

included, if necessary.

• Any actions related to the use of WAGO software may only be performed by qualified

staff with sufficient knowledge to use the respective PC system.

Steps in which files are created or changed on a PC system may only be performed by

qualified employees with sufficient knowledge in the administration of the PC system

used in addition to file creation or modification.

Steps that change the PC system’s behavior within a network may only be performed

by qualified employees with sufficient knowledge of administration of the responsible

network.

• Comply with the laws, standards, guidelines, local regulations and accepted technol-

ogy standards and practices applicable at the time of installation.

2.2 Indirect Safety

• If automation solutions are implemented that can cause personal injury or major prop-

erty damage in the event of failure, you must take appropriate measures to ensure that

the system remains in a safe operating state even in the event of failure.

• Give all products in a network different IP addresses.

• Never connect a PC on which a DHCP server is installed to a global network. In larger

networks, there is usually already a DHCP server that can cause collisions and subse-

quent network failure.

• Use only the latest security software.

• Uninstall or disable all software components or programs on your PC that are not re-

quired for the intended use.

• If there are access problems, check whether the e!RUNTIME runtime system is acti-

vated on the connected devices. Use a software tool (depending on the hardware) to

perform the check or use the Web-Based Management System.

Overview

Product manual | Version: 1.0.1 9

Application “WAGO Cloud Building Operation and Control”

3Overview

General Infomation

The application “WAGO Cloud Building Operation and Control” is an application of the

WAGO Cloud. The application is used to centrally collect and analyze data from proper-

ties with technical building equipment. Technical building equipment is understood to

mean technical facilities that are suitable for using a building in an energy-efficient man-

ner and for controlling and regulating it as required. Technical building equipment can be

a central ventilation or air conditioning system, for example. These requirements for a

building are often placed on the following facilities or buildings, for example:

Example: Public facilities

• Schools

• Kindergartens

• Gymnasiums and sports facilities

• Swimming pools

• Administrative buildings

Example: Commercial buildings

• Company offices or production facilities

• Workshops

• Storage facilities

Example: Sales outlets

• Food supplier offices

• Wholesale market offices

• Retail chain offices

Example: Technical facilities

• Substations

• Pumping stations

• Wastewater treatment plants

• Gas pressure regulating stations

Design

The application “WAGO Cloud Building Operation and Control” is designed to be opened

directly from the WAGO Cloud. The basic functionality is identical to the WAGO Cloud.

The specific functions of the application “WAGO Cloud Building Operation and Control”

are described in this Product Manual. For general information on the WAGO Cloud,

please use the respective & Product Manual.

Product Manual

As a prime example of this Product Manual would be the property management of a ficti-

tious district administration, which maintains and operates educational facilities with tech-

nical building equipment at individual locations. There is a corresponding entry in the ap-

plication “WAGO Cloud Building Operation and Control” for each individual educational

institution in the district administration that contains all transmitted data.

Requirements

10 Product manual | Version: 1.0.1

Application “WAGO Cloud Building Operation and Control”

4Requirements

General Requirements

The general and technical requirements apply for using the WAGO Cloud. You can find

them in the corresponding & Product Manual.

Specific Requirements

• You know the structure and graphical user interface of the WAGO Cloud.

• The basic functions of the WAGO Cloud are familiar to you.

• You have enabled the application ”WAGO Cloud Building Operation and Control” in

your subscription (see 8Activation [}10]).

• The “Properties” subarea is available in the starting view of the WAGO Cloud.

4.1 Activation

The application “WAGO Cloud Building Operation and Control” can be ordered using item

No. 2076-1011 / 2000-0001. The application is then provided by WAGO in the subscrip-

tion. Contrary to WAGO Cloud, this application does not require a license for activation.

The application is then available in all workspaces of the WAGO Cloud. The application is

not limited to one workspace!

More information is available at üwww.wago.com.

Starting

Product manual | Version: 1.0.1 11

Application “WAGO Cloud Building Operation and Control”

5Starting

5.1 Start the Application

To start the application “WAGO Cloud Building Operation and Control”, a few basic steps

are necessary in the WAGO Cloud:

1. Establishing and Securing an Internet Connection to the Device via ETHERNET

2. Register a New User in WAGO Cloud

3. Register and Connect a Device in WAGO Cloud

The individual steps are described in detail in the & Product Manual of the WAGO

Cloud in Section “Starting”.

The application “WAGO Cloud Building Operation and Control” can only be launched af-

ter the aforementioned steps have been performed (see 8Launch the Application

[}11]).

5.2 Launch the Application

1. Open the WAGO Cloud.

2. Create a new workspace or open an existing workspace.

3. In the start view, click the [Property Management] subarea.

ðThe application “WAGO Cloud Building Operation and Control” opens.

ðYour defined workspace appears in the start view.

Figure1: [Property Management] Subarea

5.3 Import Required Information

The application is structured in such a way that all necessary information is imported via

an external Excel file in .xlsx format. Information itself can be a single entry, for example,

that is displayed in the 8Graphical User Interface [}15]. In the Excel file, all informa-

tion can be managed and structured accordingly so that it is logically displayed in the ap-

plication in a tree structure:

Starting

12 Product manual | Version: 1.0.1

Application “WAGO Cloud Building Operation and Control”

Figure2: Tree Structure with Various Entries

The design and structure of all information are thus defined outside of the application.

How to manage and structure the information accordingly is described in a sample file.

This file is named “Kindergarden_Structure.xlsx” and is available at üwww.wago.com.

Note

Use the Excel file permanently as a template!

An Excel file that has already been created can be used permanently as a template after

the initial import. With each import, the application automatically detects newly created

entries or changed structures and, for example, adapts an existing tree structure accord-

ingly. It is therefore not necessary to hold and maintain several individual Excel files!

Further and additional documentation can be found at üwww.wago.com.

Starting

Product manual | Version: 1.0.1 13

Application “WAGO Cloud Building Operation and Control”

5.3.1 Import Excel File for the First Time

Proceed as follows to import an existing Excel file for the first time:

1. Click [Import].

ð“Excel Import” dialog opens.

2. Click [Select file] and select the file to import.

3. Select Replace data in the selection field.

4. Click [Import].

ðThe file is uploaded.

ðThe tree structure created is visible in the application.

Starting

14 Product manual | Version: 1.0.1

Application “WAGO Cloud Building Operation and Control”

5.3.2 Import Excel File Again

Proceed as follows to import an existing Excel file again:

1. Click [Import].

ð“Excel Import” dialog opens.

2. Click [Select file] and select the file to import.

3. Select Merge data in the selection field if you want to merge all existing data with

updated data.

4. Select Add and replace data in the selection field if you want to overwrite all exist-

ing data with updated data.

5. Click [Import].

ðThe file is uploaded.

ðThe tree structure created is visible in the application.

Graphical User Interface

Product manual | Version: 1.0.1 15

Application “WAGO Cloud Building Operation and Control”

6Graphical User Interface

The graphical user interface is described in detail in the & Product Manual for the

WAGO Cloud. More detailed information on the basic structure and individual functions

are therefore not described here.

6.1 “WAGO Cloud Building Operation and Control” Application

The application can be divided into three main areas:

Figure3: “WAGO Cloud Building Operation and Control” Application

Table2: Legend for Figure “WAGO Cloud Building Operation and Control” Application

Position Designation Description

1 Side Menu Workspace side menu

2 Location Path Shows where you are currently within the

WAGO Cloud.

3 Action Area Shows the information and setting options of the

action area.

Graphical User Interface

16 Product manual | Version: 1.0.1

Application “WAGO Cloud Building Operation and Control”

6.1.1 Side Menu

Figure4: Side Menu

Table3: Legend for Figure “Side Menu”

Position Designation Description

1Minimize or maximize the side menu Minimizes/maximizes the side menu view,

depending the state it starts in.

In the minimized state, only the application

icon is displayed. In maximized state, the

full side menu appears with all menu items.

2Search Searches the structured content from the imported Ex-

cel file.

You can navigate directly to individual properties using

the respective search term. In addition, the tree struc-

ture opens with each entry. This makes it easier to

search for a large number of properties.

3Content from the imported Excel file Structured content from the imported Excel file

4Buttons Buttons for importing and exporting a structured Excel

file

Graphical User Interface

Product manual | Version: 1.0.1 17

Application “WAGO Cloud Building Operation and Control”

6.1.2 Action Area

The action area has two different views:

•Complete view

•Detail view

Complete view

This view contains a complete overview of all subordinate properties. Performance indi-

cators for complete areas can be viewed and reports can be created. Specific parameters

can be configured. All individual properties are also listed.

The complete view is identified by a “directory” icon (see Section 8Action Area – Com-

plete View [}19]).

Detail view

This view contains specific performance indicators for an individual property, such as in-

formation on ventilation, heating and air conditioning. Specific parameters can be config-

ured.

The detailed view is identified by a “property” icon (see Section 8Action Area – Detail

View [}23]).

Regardless of the selected view, the action area can be divided into two areas:

Graphical User Interface

18 Product manual | Version: 1.0.1

Application “WAGO Cloud Building Operation and Control”

Figure5: Action Area

Table4: Legend for Figure “Action Area”

Position Designation Description

1Menu bar with buttons Displays a specific menu bar depending on the

selected view.

The buttons are universal. The are described in

Section 8Buttons [}19].

2Subarea In this area, you can view recorded performance

indicators and configure specific parameters.

Graphical User Interface

Product manual | Version: 1.0.1 19

Application “WAGO Cloud Building Operation and Control”

Buttons

There is a button in the menu bar that can be used to select one of two modes. The but-

ton has two presentations:

Figure6: “Edit Mode” button

Figure7: “View Mode” button

The display and corresponding behavior change depending on the mode set. The buttons

are functionally identical in front of the selected view and in the entire action area.

Table5: Menu Bar

Button Description

[Edit Mode] Switches to edit mode.

Parameters can be edited in this mode. Read only is suspended.

[View Mode] Switches to view mode.

Parameters cannot be edited in this mode. Read only is enabled.

6.1.2.1 Action Area – Complete View

For complete areas of properties, recorded performance indicators can be viewed and

parameters can be configured in this action area. Reports can also be created.

6.1.2.1.1 Menu Bar

The menu bar has the following tabs:

Figure8: Action Area – Complete View: Menu Bar

Each tab leads to a separate subarea.

Table6: Menu Bar

Tab Subarea

Overview Opens the 8“Overview” Subarea [}19]

Reporting Opens the 8“Reporting” Subarea [}22]

6.1.2.1.2 Subareas

6.1.2.1.2.1 “Overview” Subarea

This subarea is called up from the “Overview” tab.

The individual tabs are described in the Section 8Menu Bar [}19].

The subarea can be divided into two views:

Graphical User Interface

20 Product manual | Version: 1.0.1

Application “WAGO Cloud Building Operation and Control”

Figure9: “Overview” Subarea

Table7: Legend for Figure “Overview” Subarea

Position Designation Description

1Status and Key Performance Indicator View Shows the status and determined key perfor-

mance indicators of all subordinate properties.

2“Properties” summary Shows the status of all subordinate properties in

detail.

6.1.2.1.2.1.1 Status and Performance Indicator View

The status and key performance indicator view provides an overview of the current status

and recorded performance indicators. The view relates to all subordinate properties. It

consists of several individual views:

Figure10: Status and Energy Indicator View

Table8: Legend for Figure “Status and Key Performance Indicator View”

Position Designation Description

1“Status” Single View 8“Status” Single View [}20]

2“Key Performance Indicator” Single View 8“Key Performance Indicator” Single View

[}21]

“Status” Single View

The subordinate properties can be monitored in the “Status” single view. The monitoring

refers to the key performance indicators of individual building systems that are available

for the respective property.

Page is loading ...

WAGO Application "Cloud Building Operation and Control" User manual

WAGO Application "Cloud Building Operation and Control" User manual

WAGO Application "Cloud Building Operation and Control" User manual

Related papers

Other documents