Samsung Z-890 User manual

Brand: Samsung

Model: Z-890

Category: LED TVs

Type: User manual

imagine the possibilities

Thank you for purchasing this Samsung

product. To receive more complete service,

please register your product at

www.samsung.com/register

Model Serial No.

LED TV

Installation manual

[HG890_ZA]Install_Guide-00ENG.indd 1 2013-04-12  5:30:34

Figures and illustrations in this User Manual are provided for reference only and may differ from actual product appearance.

Product design and speciﬁcations may be changed without notice.

Introduction

This TV has functionality that lets it interact with a set-back box (SBB/STB) and with other TVs in a computer-controlled system for hotels and

other hospitality businesses.

Interactive : When the TV is powered-up initially, it sends a command to identify the connected SBB/STB. If it identiﬁes the SBB/STB, the TV switches to

ONLINE mode which gives full control of the TV to the SBB/STB.

When the TV is in ONLINE mode, it stops accepting IR (Samsung remote) commands and acts according to the interface protocol.

Stand-Alone: If you are not using an SBB/STB and the TV cannot or does not identify an SBB/STB, you should switch the TV to STAND-ALONE mode

with restricted operation.

Operational Modes

When this TV is in Hotel mode and is operated with an SBB/STB, it is in one of two states: ONLINE or STAND-ALONE

• In the STAND-ALONE state, the TV will act as a Hotel TV, but without active communication. This is to prevent guests from trying to cheat the system

by disconnecting the SBB/STB.

To set the options for Stand-alone or Interactive (Online) mode, refer to pages 19-23 (Setting the hotel option data : Menu Items.)

• You can restrict all (or some) operations to prevent guests from "cheating" the TV system.

• You can can set Volume limits and lock or unlock the Panel buttons.

Still image warning

Avoid displaying still images (such as jpeg picture ﬁles) or still image elements (such as TV channel logos, panorama or 4:3 format images, stock or news

bars or crawls) on the screen. Displaying still pictures continually can cause uneven screen wear, which will affect image quality. To reduce the chance that

this effect will occur, please follow the recommendations below:

• Avoid displaying the same TV channel for long periods.

• Always try to display a full screen image.

• Reduce brightness and contrast to help to prevent the occurrence of after-images.

• Use all TV features designed to reduce image retention and screen burn-in. Refer to the proper user manual section for details.

Ensuring Proper Ventilation

When you install the TV, maintain the distances shown below between the TV and other objects ((walls, cabintet sides, etc.) to ensure proper ventilation.

Failing to do so may result in a ﬁre or problems with the TV caused by an increase in its internal temperature.

✎

When using a stand or wall-mount, use parts provided by Samsung Electronics only.

If you use parts provided by another manufacturer, it may cause a problem with the product or cause the product to fall, leading to serioius injury.

Installation with a stand. Installation with a wall-mount.

4 inches4 inches

4 inches

4 inches4 inches

4 inches

Additional Information

✎

The appearance of the TV and its accessories may differ from the illustrations in this manual, depending on the TV.

✎

Be careful when you touch the TV if it is on or has been on for a period of time. Some parts can be hot.

Power

Online Mode

Poll Rate 20/sec

Stand-alone

Mode

SBB/STB Online if one success

within 10 attempts

SBB/STB

Online-10

consecutive fails

SBB/STB Status-Attempt

every 2 seconds

[HG890_ZA]Install_Guide-00ENG.indd 2 2013-04-12  5:30:34

Contents

ENGLISH

English

Symbols Used in this Manual

Indicates that you can press the

TOOLS button on the remote control

to use this function.

Note One-Touch Button

TOOLS

y Introduction .............................................................................................................................................................. 2

y Operational Modes ................................................................................................................................................... 2

y Still image warning .................................................................................................................................................... 2

y Ensuring Proper Ventilation ...................................................................................................................................... 2

y Additional Information ............................................................................................................................................... 2

y Accessories .............................................................................................................................................................. 4

y Installing the LED TV Stand ....................................................................................................................................... 5

y Using the TV's Controller .......................................................................................................................................... 6

y The Connection Panel ............................................................................................................................................... 7

y The Remote Control .................................................................................................................................................. 9

y Using the Smart Touch Control ............................................................................................................................... 11

y Using the touch pad ............................................................................................................................................... 14

y Connecting to the Network ..................................................................................................................................... 16

y Connecting the TV to an SBB or STB ..................................................................................................................... 18

y Connecting the Bathroom Speakers ....................................................................................................................... 20

y Connecting the MediaHub HD ................................................................................................................................ 21

y Connecting the RJP (Remote Jack Pack) ................................................................................................................ 22

y Setting the Hotel Option Data ................................................................................................................................. 24

y Installing the Wall Mount ......................................................................................................................................... 43

y Anti-theft Kensington Lock ...................................................................................................................................... 48

y Display Resolution................................................................................................................................................... 48

y Speciﬁcations ......................................................................................................................................................... 49

y Dimensions ............................................................................................................................................................. 50

[HG890_ZA]Install_Guide-00ENG.indd 3 2013-04-12  5:30:34

English

Accessories

✎

Please make sure the following items are included with your LED TV. If any items are missing, contact your dealer.

✎

The items’ color and shape may vary, depending on the model.

✎

The parts for the stand are listed under Stand Components on the following page.

y Remote Control (AA59-00817A) & Batteries (AAA x 2)

y Smart Touch Control (AA59-00830A) & Batteries (AAA x 2)

y Owner’s Instructions

y Power Cord

y Data Cable (BN39-00865B, BN39-01011C)

y Warranty card / Safety Guide / Quick Setup Guide

(Not available in all locations)

Screw Cover (2ea) Cable clip Wall mount adapter (2ea)

TV holder kit Power inlet cover

[HG890_ZA]Install_Guide-00ENG.indd 4 2013-04-12  5:30:35

English

Installing the LED TV Stand

Components

When installing the stand, use the provided components and parts.

1 EA

2 EA

L R

x8 (M4 X L12)

Stand (depending on the model)

Guide Stand

Screws

✎

NOTE

y Make sure to distinguish between the front and back of the Stand and Stand Guide when connecting them.

y Make sure that at least two people lift and move the TV.

y When placing the product on a console or shelf, make sure that the stand does not protrude out of the console or shelf.

This may cause the product to fall off and result in a malfunction or injury.

1 2

x4 (M4 X L12)

✎

Lay the TV on a soft surface, screen side down.

✎

Use the packing material to protect the screen.

[HG890_ZA]Install_Guide-00ENG.indd 5 2013-04-12  5:30:37

English

Using the TV's Controller

✎

The color and shape of the TV Controller may vary depending on the model.

✎

The TV's Controller, a small joy stick like button on the bottom right side of the TV, lets you control the TV without the

remote control.

Power on Turn the TV on by pressing the Controller when the TV is in standby mode.

Adjusting the volume

Adjust the volume by moving the Controller from side to side when the power is on.

Selecting a channel

Select a channel by moving the Controller backwards and forwards when the power is on.

Using the Function menu

To view and use the Function menu, press and release the Controller when the

power is on. To close the Function menu, press and release the Controller again.

Selecting the MENU (

)

With the Function menu visible, select the MENU (

) by moving the Controller

to the left. The OSD (On Screen Display) Menu appears. Select an option by

moving the Controller to the right. Move the Controller to the right or left, or

backwards and forwards to make additional selections. To change a parameter,

select the it, and then press the Controller.

Selecting the SMART

HUB (™)

With the Function menu visible, select SMART HUB (™) by moving the

Controller upwards. The SMART HUB main screen appears. Select an

application by moving the Controller, and then pressing the Controller.

Selecting a Source (

)

With the Function menu visible, open the Source screen (s) by pushing the Controller

to the right. The Source screen appears. To select a source, move the Controller back

and forth. When the source you want is highlighted, press the Controller.

Power Off (

) With the Function menu visible, select Power Off (

) by pulling the Controller

forwards, and then press the Controller.

✎

To close the Menu, SMART HUB, or Source, press the Controller for more than 1 second.

Standby mode

Your TV enters Standby mode when you turn it off, and continues to consume a small amount of electric power. To be safe

and to decrease power consumption, do not leave your TV in standby mode for long periods of time (when you are away on

vacation, for example). It is best to unplug the power cord.

MIC

STB

SOURCE

VOICE

VOL

LIGHT

ALARM

SLEEP

SMART HUB

GUIDERETURN

EXIT

HOME

TV Controller

Turn off the TV.

Open Smart Hub.

Open the menu. Select a source.

The control stick is located at the

lower-left corner on the back of the TV.

Remote control sensor

When you use the Smart Touch Control,

the standby LED does not respond,

except when you press the

button.

[HG890_ZA]Install_Guide-00ENG.indd 6 2013-04-12  5:30:37

English

The Connection Panel

✎

Whenever you connect an external device to your TV, make sure that power on the TV and the device is turned off.

✎

When connecting an external device, match the color of the connection terminal to the cable.

1 VARIABLE AUDIO OUT: Used for the audio output to the Bathroom speaker. Connect the Bathroom Wall Box and the

Variable port (RCA).

2 VOL-CTRL:

Used to control the volume of the Bathroom speaker. Connect the Bathroom Wall Box and the VOLCTRL port.

3 USB (HDD 5V 1A)

– Connector for software upgrades and Media Play, etc.

– Service connection.

4 DIGITAL AUDIO OUT (OPTICAL): Connects to a Digital Audio component.

5 AUDIO OUT: Connects to the audio input jacks on an Ampliﬁer/Home Theater.

6 DVI AUDIO IN: Connects to the audio input jacks on an Ampliﬁer/Home Theater.

RJP

VARIABLE

AUDIO OUT

AUDIO

OUT

DVI

AUDIO IN

VOL-CTRL

HDMI IN 3

EX-LINK

DATA

HDMI IN 1

(ARC)

AIR/CABLE

87 90 !@

(HDD 5V 1A)

[HG890_ZA]Install_Guide-00ENG.indd 7 2013-04-12  5:30:38

English

7 HDMI IN 1 (ARC), 2 (DVI), 3: Connects to the HDMI jack of a device with an HDMI output.

✎

No sound connection is needed for an HDMI to HDMI connection. HDMI connections carry both audio and video.

✎

Use the HDMI IN 2(DVI) jack for a DVI connection to an external device. Use a DVI to HDMI cable or DVI-HDMI

adapter (DVI to HDMI) for the video connection and the PC/DVI AUDIO IN jacks for audio.

8 EX-LINK: The EX-LINK connection is for service only.

9 DATA

– Used to support data communication between the TV and the SBB.

– Connects using RJ-12 TV type plugs.

0 LAN: Connect to a wired LAN using CAT 5 cable.

! COMPONENT IN / AV IN

– Connect audio cables to "R-AUDIO-L" on your TV and the other ends to corresponding audio out jacks on an A/V

device.

– Connects Component video / audio.

– The COMPONENT IN jack is also used as the VIDEO 1 jack.

– Connect component video cables (optional) to the component jacks ("P

R", "PB", "Y") on the rear of your TV and the

other ends to corresponding component video out jacks on a DVD player.

– If you want to connect both the Set-Top Box and a DVD player, you should connect the Set-Top Box to the DVD and

connect the DVD to the component jacks ("PR", "PB", "Y") on your TV.

– The PR, PB and Y jacks on your component devices (DVD) are sometimes labeled Y, B-Y and R-Y or Y, Cb and Cr.

– Connect RCA audio cables (optional) to "R - AUDIO - L" on the rear of the TV set and the other ends to corresponding

audio out jacks on the external device.

– When connecting to AV IN, the color of the AV IN [Y/VIDEO] jack (Green) does not match the color of the video cable

(Yellow).

@ ANT IN (AIR/CABLE)

– To view television channels correctly, the TV must receive a signal from one of the following sources:

– An outdoor antenna / A cable television system / A satellite receiver

[HG890_ZA]Install_Guide-00ENG.indd 8 2013-04-12  5:30:38

English

The Remote Control

Remote Control (AA59-00817A)

✎

This remote control has Braille points on the Power, Channel, and Volume buttons and can be used by visually

impaired customers.

HOME

CONTENT

ALARM

SLEEPCC

CHVOL

Turns the TV on and off.

Display and select the available video

sources.

Return to the previous channel.

Change channels.

Displays My Contents, Watch TV and

Source icons on the TV screen.

Exit the menu.

Press to display channel and TV information

on the TV screen.

SLEEP: Sets the Sleep Timer.

: Turns the 3D image on or off.

CC: Controls the caption decoder.

Cut off the sound temporarily.

Press to directly access channels.

Adjust the volume.

Display the channel list on the screen.

Display the main on-screen menu.

HOME: Only used in Widget TV.

Quickly select frequently used functions.

Return to the previous menu.

Use these buttons in the Media Play and

Anynet+ modes.

Select on-screen menu items and change

menu values.

Press to select additional digital channels

being broadcast by the same station. For

example, to select channel ‘54-3’, press

‘54’, then press '-' and ‘3’.

Buttons used in Channel list, Media Play

menu, etc.

button: Enter the hour your want the TV to

turn on.

[HG890_ZA]Install_Guide-00ENG.indd 9 2013-04-12  5:30:38

English

Installing batteries (Battery size: AAA)

Match the polarity of the batteries to the symbols in the battery compartment.

After you have installed the batteries, use a screwdriver to screw in the screw that holds the battery cover

closed.

✎

NOTE

• Use the remote control within 23~33 feet of the TV.

• Bright light may affect the performance of the remote control. Avoid using near ﬂuorescent lights or

neon signs.

• The color and shape of the remote may vary depending on the model.

[HG890_ZA]Install_Guide-00ENG.indd 10 2013-04-12  5:30:38

English

Using the Smart Touch Control

Smart Touch Control (AA59-00830A)

✎

This remote control has Braille points on the Power, Channel, and Volume buttons and can be used by visually

impaired customers.

MIC

STB

SOURCE

VOICE

VOL

ALARMLIGHT MENU SLEEP

SMART HUB

GUIDERETURN

EXIT

HOME

MUTE

Touch Pad

• Drag on the touch pad to move the

focus on the screen.

• Press the touch pad to run,

activate, or select the highlighted

item.

• Press and hold the touch pad to

display the Channel List.

VOICE Take your voice command and

enter a text using your voice.

Displays a virtual remote control on

the screen. See the e-Manual chapter,

Controlling the TV > Virtual Remote

Control.

Changes channels.

Displays the EPG (Electronic Program

Guide).

Brings up Smart Hub applications.

See the e-Manual chapter, SMART TV

Features > Smart Hub.

✎

To exit an application that is

running easily, press the

™

button.

Not Available

Turns the TV on and off.

Displays and selects the available video

sources.

Returns to the previous menu..

MIC

STB

SOURCE

VOICE

VOL

ALARMLIGHT

MENU SLEEP

SMART HUB

GUIDERETURN

EXIT

HOME

MUTE

MUTE Cuts

off the sound

temporarily.

Adjusts the volume.

Use Voice Recognition function with

the microphone embedded in remote

control.

✎

The Voice Recognition function

can be affected by unclear

pronunciation, voice level, or

surrounding noise.

LIGHT: Turn on the backlight for the

buttons. The backlight lasts for only a

few seconds. Turns the remote control

light on or off. When on, the buttons

become illuminated for a moment when

pressed. (Using the remote control with

this button set to On will reduce the

battery usage time.)

ALARM

Enter the hour your want the

TV to turn on.

MENU: Opens the OSD.

SLEEP: Sets the Sleep Timer.

Only Used in Widget TV.

[HG890_ZA]Install_Guide-00ENG.indd 11 2013-04-12  5:30:39

English

Connecting to the TV

In order to operate the TV using a Smart Touch Control, you must ﬁ rst pair it to the TV via Bluetooth. However, the Smart

Touch Control is only available for the paired Samsung TV.

1. To turn on the TV, point the Smart Touch Control at the remote control receiver of the TV and press the P button.

The remote control receiver's location may vary depending on the model.

2. A Bluetooth icon will appear at the bottom left of the screen as shown below. The TV will then attempt to connect to

the Smart Touch Control automatically.

Inserting the Batteries (AAA X 2)

1. Slightly lift the battery cover by pulling the strap or by inserting a plastic card (e.g. a credit card) into the notch on

the side of the remote and twisting the card slightly. Next, grasp the loosened cover in one hand and the top of the

remote in the other and gently pull them apart.

2. Insert 2 AAA batteries, making sure to align the positive and negative ends correctly.

3. Align the battery cover with the back of the remote control, and then press down along the edges until it is

completely attached to the remote control.

[HG890_ZA]Install_Guide-00ENG.indd 12 2013-04-12  5:30:39

English

Reconnecting the Smart Touch Control

If you need to rees

tablish the connection between the TV and the Smart Touch Control, press the pairing button at the

back of the Smart Touch Control, pointing at the remote control sensor of the TV.

The pairing button can be accessed by removing the Smart Touch Control's battery cover. Pressing the pairing button

automaticall

y reestablishes the connection between the Smart Touch Control and the TV.

Low Battery Power Warning

If the battery becomes low while using the Smart Touch Control, the following alarm window appears at the bottom of

the left screen. If the alarm window pops up, replace the batteries of the Smart Touch Control. Use alkaline batteries for

longer usage.

[HG890_ZA]Install_Guide-00ENG.indd 13 2013-04-12  5:30:39

English

Using the touch pad

Use the touch pad to implement various commands. Navigate to Tutorial (System > Device Manager > Smart Touch

Control Settings > Tutorial) to view an on-screen guide to using the Smart Touch Control.

Dragging Tap

HOME

Drag on the touch pad to move the focus, pointer, or highlight in the

direction the ﬁnger is dragging.

Press the touch pad to select the item highlighted or in focus.

When watching TV, press and hold the touch pad for 2 seconds displays

the channel list. On some apps, press and hold the touch pad for 2

seconds displays a list of functions available for the app.

Show Status and Notiﬁcation Banner

Press the MORE button on the Smart Touch Control and then select STATUS on the virtual remote panel that appears

on the screen. The status and alarm banner appears at the top of the screen. For more information about using the

status and alarm banner.

[HG890_ZA]Install_Guide-00ENG.indd 14 2013-04-12  5:30:39

English

Using the Virtual Remote Panel

Press the MORE button to display the virtual remote panel on the TV screen. The virtual remote panel consists of the number

panel, a playback control panel, and the quick access panel. Use the touch pad to highlight and select icons, numbers, and

buttons on the panels.

✎

The displayed virtual remote panel on the TV screen may differ depending on the country.

E F G

P. Size CC

MTS

STATUS

PIP

TOOLS

INFO

Web Brow...

MENU3DTOOLS

ALARM

SLEEP

P.Mode

INFO

Channel History

No Channel numbers

have been saved.

Changing the Virtual Remote Panel

You can change which virtual remote panel is displayed on the TV screen. To shift between panels, move the focus highlight

beyond the left or right edge of the displayed panel.

Use left/right scroll function on the touchpad to change the panel easily.

Using the Number Panel

Use the number panel to enter numbers on a keypad screen or webpage or to change the channel while watching TV.

Changing the channel using the number pad leaves a record, allowing you to easily return to previous channels.

Using the Playback Control Panel

Use the playback control panel to pause, rewind, fast forward, skip to the next ﬁle, select a function with the

{

}

buttons, and much more while enjoying media content.

Using the Quick Access Panel

Use the buttons on the quick access panel to bring up the TV's MENU, INFO screens. Note that the buttons that appear may

vary depending on the operating mode of the Smart Touch Control (with the TV only, as a universal remote, etc.).

[HG890_ZA]Install_Guide-00ENG.indd 15 2013-04-12  5:30:39

English

Connecting to the Network

You can set up your TV so that it can access the SMART TV applications through your local area network (LAN) using a wired

or wireless connection.

✎

After you have “physically” connected your TV to your network, you must configure the network connection to complete

the process. You can configure the connection during the Initial Setup process (see page 35) or after the Initial Setup

process, through the TV’s menu.

Network Connection - Wireless

You can connect your TV to your local area network (LAN) through a standard wireless router or modem.

This TV supports the IEEE 802.11a/b/g and n communication protocols. Samsung recommends using IEEE 802.11n. When

you play video over a network connection, the video may not play smoothly.

Most wireless network systems incorporate a security system that requires devices that access the network through an access

point or AP (typically a wireless IP Sharer - router or modem) to transmit an encrypted security code called an access key.

Your TV is compatible with the following security protocols:

y Authentication Mode: OPEN, SHARED, WPAPSK, WPA2PSK

y Encryption Type: WEP, TKIP, AES

In compliance with the newest Wi-Fi certiﬁcation speciﬁcations, Samsung TVs do not support WEP or TKIP security encryption

in networks running in the 802.11n mode.

LAN Cable (Not Supplied)

The LAN Port on the Wall

Wireless IP Router or Modem

(router having DHCP Server)

[HG890_ZA]Install_Guide-00ENG.indd 16 2013-04-12  5:30:40

English

Network Connection - Wired

There are three main ways to connect your TV to your network using cable, depending on your network setup. They are

illustrated below:

✎

The TV does not support network speeds of 10Mbps or less.

✎

Use Cat 6 or CAT 7 (STP Type*) cable for the connection. (*Shielded Twisted Pair)

The Modem Port on the Wall

TV Rear Panel

LAN Cable (Not Supplied)Modem Cable (Not Supplied)

External Modem

(ADSL / VDSL / Cable TV)

The LAN Port on the Wall

TV Rear Panel

LAN Cable (Not Supplied)

The Modem Port on the Wall

TV Rear Panel

LAN Cable

(Not Supplied)

Modem Cable

(Not Supplied)

LAN Cable

(Not Supplied)

External Modem

(ADSL / VDSL / Cable TV)

IP Router that has a

DHCP Server

[HG890_ZA]Install_Guide-00ENG.indd 17 2013-04-12  5:30:41

English

Connecting the TV to an SBB or STB

1. Connect the DATA jack of the TV to the [ETH MODEM] jack of the STB (SBB) with the Data cable.

✎

Use data communication.

¦ Connecting the Audio Output to an Audio Ampliﬁer

1. Connect the AUDIO OUT port of the TV to the Audio In port of an audio ampliﬁer with a stereo cable.

AUDIO IN

AUDIO

OUT

DVI

AUDIO IN

HDMI IN 3

UDI

MI IN 3

AUDIO

OUT

TV Rear Panel

Audio

Amplifier

1 Stereo cable

ETH MODEM

DATA

TV Rear Panel

Data Cable

[HG890_ZA]Install_Guide-00ENG.indd 18 2013-04-12  5:30:41

English

¦ List of Vendors and Compatible Data Cables Supplied with the TV

y Conﬁrm that you are using the correct data cable for your vendor. Refer to the code label on the data cables.

[HG890_ZA]Install_Guide-00ENG.indd 19 2013-04-12  5:30:41

English

Connecting the Bathroom Speakers

You can connect the Bathroom Speakers using the following method.

¦ Connecting through the Variable Output (available without an external ampliﬁer)

VARIABLE

AUDIO OUT

VOL-CTRL

(HDD 5V 1A)

UDI

L-CTRL

(

HDD 5V 1A

)

VARIABLE

AUDIO OUT

VOL-CTRL

VOL+

VOL

TV Rear Panel

Volume Control Box

Speaker

1. Connect the VARIABLE AUDIO OUT port of the TV to the Bathroom Wall Speakers of the hotel.

Speaker +

Speaker -

N/C

2. Connect the VOL-CTRL jack of the TV to the Volume Control Box Switch port on the Bathroom Wall of the hotel.

✎

The maximum speaker output is 4W, 8Ω.

✎

The VARIABLE AUDIO OUT port supports MONO sound out only.

y Installing the Volume Control

– If you conﬁgure the Volume Control Box as shown in the ﬁgure, you can control the volume of the bathroom speakers.

– The jack that connects the Volume Control Box to the TV is a 3.5mm normal Phone jack.

– Volume Control Box switch is a Tact switch.

✎

Setting the Sub AMP Mode

– 0: Turns the Sub AMP function off (PWM off).

– 1: Determines the Sub volume according to the main volume control. the sub volume is determined according to the

Power On Volume, the Min Volume, and the Max Volume values of Hotel Mode.

– 2: Determines the volume according to the bathroom control panel setting.

y Variable Output Port Speciﬁcations

– Speaker Wire: Use speaker cable no more than 82 feet (25m) in length.

Volume Control Box

VOL - DOWN

( White 1 )

VOL - UP

( Black /Red 2 )

GND

( Shield Wire 3 )

VOL +

VOL

[HG890_ZA]Install_Guide-00ENG.indd 20 2013-04-12  5:30:42

Page is loading ...

Samsung Z-890 User manual

Brand: Samsung

Model: Z-890

Category: LED TVs

Type: User manual

Download PDF

report

Samsung Z-890 User manual

Samsung Z-890 User manual

Related papers

Other documents