Krell Industries HTS 2 User manual

"rilE I--EAr’~ER IN AUCIIO ENCtINEERINO

Home Theater

Standard

Surround

Preamp/Processor

Instructions for Use

Owner’s Reference

Home Theater Standard

Surround Preamp/Processor

Instructions for Use

v 01.2

Krell Industries, Inc.

45 Connair Road

Orange, CT 06477-3650 USA

TEL 203-799-9954

FAX 203-891-2028

E-MAIL [email protected]

WEBSITE http://www.krellonline.com

This product complies with the EMC directive (89/336/EEC) and the low-voltage directive (73/23/EEC).

WARNINGS

The Home Theater Standard must be placed on a firm level surface where it is not exposed to dripping or

splashing.

The ventilation grids on the top and bottom of the Home Theater Standard must be unobstructed at all

times during operation. Do not place flammable material above or beneath the component.

Do not remove or bypass the ground pin on the end of the AC power cord. This could cause radio frequen-

cy interference (RFI) to be introduced into your playback system.

Before making connections to The Home Theater Standard, make sure the back panel power switch is off.

Make sure all cable terminations are of the highest quality and free from frayed ends, short circuits, or cold

solder joints.

THERE ARE NO USER SERVICEABLE PARTS INSIDE ANY KRELL PRODUCT.

Please contact your authorized Krell dealer, distributor, or Krell if you have any questions not addressed in

this Owner’s Reference.

This product is manufactured in the United States of America. Krell® is a registered trademark of Krell Industries, Inc., and is restricted for use by Krell

Industries, Inc., its subsidiaries, and authorized agents. Krell Current Mode

TM

is a trademark of Krell Industries, Inc. "DTS" and "DTS Digital Surround" are

registered trademarks of Digital Theater Systems, Inc. TosLink is a trademark of Toshiba Corporation. PHAST Link is a trademark of Phast Corporation.

Manufactured under license from Dolby Laboratories. "Dolby," "Pro Logic," and the double-D symbol are trademarks of Dolby Laboratories. Confidential

tive companies.

Contents

INTRODUCTION

DEFINITION OF TERMS

UNPACKING

PLACEMENT

AC Power Guidelines

GETTING STARTED

Read This First

An Introduction to System Setup

FRONT PANEL DESCRIPTION

BACK PANEL DESCRIPTION

REMOTE CONTROL DESCRIPTION

Battery Installation and Removal

CONNECTING THE HOME THEATER STANDARD

TO YOUR SYSTEM

First: Connect Analog and Digital Sources

Next: Connect Video Sources

Last: Connect Amplifier(s)

SYSTEM SETUP AND CONFIGURATION OVERVIEW

SYSTEM SETUP AND CONFIGURATION

Navigating the Menu

Accessing the Main Menu

Configure Speakers

Listening Room Setup

Calibrate Volume .

Configure Devices

Configure Level Adjustment

Operation

SAVING SETUP, RECALLING SETUP, AND RESTORING FACTORY

DEFAULT SYSTEM CONFIGURATION SETTINGS

OPERATING THE HOME THEATER STANDARD

On/Off/Stand-by

Tape Input and Output

Main Zone and Zone 2 Operation

Other Operation Features

WARRANTY

RETURN AUTHORIZATION PROCEDURE

SPECIFICATIONS

Page

1

3

4

5

6

8

14

18

23

24

25

26

27

29

30

32

39

44

52

53

54

55

57

58

59-60

Krell Home Theater Standard

iii

Illustrations

FIGURE 1 The Home Theater Standard Front Panel

FIGURE 2 The Home Theater Standard Back Panel

FIGURE 3 The Home Theater Standard Remote Control

Page

7

13

17

iV Krell Home Theater Standard

Introduction

Thank you for your purchase of the .Krell Home Theater Standard Surround

Preamp/Processor.

The Home Theater Standard provides optimum music and cinema soundtrack

reproduction quality through Krell Current Mode, discrete Class A direct-coupled

circuitry, and balanced outputs on all six channels. Broadcast quality switching and

circuitry--including component video, S-video, and composite video--ensure

unmatched video performance. Built-in Dolby Digital, Dolby Pro Logic, and DTS

decoding make the Home Theater Standard compatible with virtually any surround

sound source, including digital videodisc (DVD) software and digital television

broadcasts.

Dual zone capability gives you a variety of configuration possibilities for whole-house

systems. A handheld remote control, RS-232 and optional PHAST Link communications

ports, RC-5 baseband, and 12 VDC input/output (12 V trigger) interface integrate the

Home Theater Standard into any system. The Home Theater Standard’s flexible,

modular architecture allows you to upgrade hardware and software to accommodate

future surround sound formats and design enhancements.

The owner’s reference manual contains important information on placement,

installation, and operation of the Krell Home Theater Standard. Please read this

information carefully. A thorough understanding of these details helps ensure

satisfactory operation of and long life for your Home Theater Standard and related

system components.

Definition of Terms

Following are the definitions of key terms used in your owner’s reference manual.

INPUT AND OUTPUT CONNECTIONS

Balanced

A symmetrical input or output circuit that has equal impedance from both input terminals

to a common ground reference point. The industry standard for professional and sound

recording installations, balanced connections have 6 dB more gain than single-ended

connections and allow the use of long interconnect cables. Balanced connections are

completely immune to induced noise from the system or the environment.

Krell Home Theater Standard

Definition of Terms, continued

Multi-channel (DB-25)

A balanced input or output circuit that allows for the simultaneous connection of all

audio outputs plus one 5 VDC (5 Volt trigger) via a single cable. DB-25 inputs and

outputs are becoming popular for connecting an audio/video surround sound processor

and power amplifiers, simplifying the integration of the two components into your

system.

Single-ended

A two-wire input or output circuit. Use care when using single-ended connections as the

ground connection is made last and broken first. Turn the system off prior to making or

breaking single-ended connections. Single-ended connections are not recommended

for connections requiring long cable runs.

OPERATION

Off

When the power switch on the back panel is placed in the down position and LEDs turn

off, the component is off.

Stand-by Mode

When the HTS is connected to AC power and the back panel power switch is in the up

(on) position, the red stand-by LED illuminates. This indicates that the component is

stand-by mode, a low power consumption status that keeps the audio and regulator

circuits at idle. Krell recommends leaving the component in the stand-by mode when it

is not playing music.

Operational Mode

When the component is in the stand-by mode, and you press the power button on the

front panel or the power key on the remote control, the blue power LED illuminates. The

component is in the operational mode and is ready to play music.

TECHNOLOGY

Krell Current Mode

A proprietary Krell circuit topology in which the audio gain stages of a component

operate in the current rather than the voltage domain. This unique technology provides

the component with exceptional speed and a wide bandwidth.

Krell HEAT

The Krell term HEAT, or High End Audio Theater, is a design application incorporated

into Krell components to enhance multi-channel home entertainment systems. A Krell

HEAT system is an integrated home theater system consisting of a state-of-the-art Krell

preamp/processor and matching amplifiers that reproduce two channel and multi-

channel sources with audiophile sound quality, placing the audience in the middle of a

lifelike environment.

2 Krell Home Theater Standard

Unpacking

Open the box and remove the top.layer of foam. You see these items:

1 Home Theater Standard

1 IEC connector (AC power) cord

1 Home Theater Standard handheld remote control

1 CR2025 lithium battery

1

T-15 Torx wrench (small "L" type)

1 T-10 Torx wrench (small "L" type)

1 12 VDC output (12 V trigger) cables

1 packet containing the owner’s reference manual, the RS-232 Port developer’s

reference, the "read this first" insert, and the warranty registration card.

Carefully remove the unit and accessories from the box. Remove the foam end caps

and protective plastic wrap from the unit.

Note

If any of these items are not included in the shipping box, p/ease contact your

authorized Krell dealer, distributor, or Krell for assistance. Save all packing materials. If

you must ship your Home Theater Standard in the future, repack the unit in its originaJ

packaging to prevent transit damage. See Return Authorization Procedure, on

page 58.

Krell Home Theater Standard

Placement

Before you install the Home Theater Standard into your system, review the following

guidelines to choose the location for the component. This will facilitate a clean, trouble-

free installation.

The Home Theater Standard does not require any type of special rack or cabinet for

installation. For the dimensions of your Home Theater Standard see Specifications, on

pages 59-60.

The Home Theater Standard requires at least two inches (5 cm) of clearance on each

side and at least two inches (5 cm) of clearance above and below the component

provide adequate ventilation. Further, the Home Theater Standard requires at least

three inches (7 cm) of clearance between other connected components. For

installations inside cabinetry, extra ventilation may be necessary.

AC POWER GUIDELINES

The Home Theater Standard has superb regulation and does not require a dedicated

AC circuit. Avoid connections through extension cords or multiple AC adapters. High

quality 15 amp grounded AC strips are acceptable. High quality AC line conditioners or

filters may be used if they are grounded.

Power Cord

The Home Theater Standard should be used only with the power cord supplied. Contact

your authorized Krell dealer, distributor, or Krell before using any devices designed to

alter or stabilize the AC power for the Home Theater Standard.

4

Krell Home Theater Standard

Getting Started

READ THIS FIRST

Perform the following steps to make the On-Screen Display (OSD) viewable on your

video monitor. The video format and video signals of the Home Theater Standard and

the video monitor need to match before the OSD is viewable. The video format of the

video signal can be set to either NTSC or PAL.

The following table details the different video signals and video formats supported by

the Home Theater Standard:

Video Type of Connector Most Commonly Format

Signal Labeled As Standard

Composite Single-Ended RCA Video, Composite NTSC or PAL

S-Video DIN

S, SV, S-Video

NTSC or PAL

Component 3 Single-Ended RCA

Y, Cr, Cb NTSC or PAL

To select the initial video signal and video format:

1.

Connect your video monitor to the video output connectors on the Home Theater

Standard that corresponds to the input connectors on your video monitor (refer to

the above table).

2. Power on the Home Theater Standard by switching the back panel power switch to

on. Wait for the HTS to initialize. Then press the power button on the front panel.

The following diagram shows the front panel device buttons on the Home Theater

Standard and the default video signals and video formats associated with each button:

FRONT o o o o o o

PANEL DVD LD SAT VCR1 TV CD

DEVICE

o o o o o o

BUTTON

~ ~ ~ ~ ~ ~

SIGNAL Composite S-Video Component Composite S-Video Component

FORMAT NTSC NTSC NTSC PAL PAL PAL

Press the front panel device button that matches both the video format and video

signal compatible with your connected video monitor (refer to the above diagram).

This becomes the currently selected video signal output.

Krell Home Theater Standard 5

4. Verify that the video monitor’s video signal input corresponds to the Home Theater

Standard video signal output. Press the menu key on the remote control to verify

that the OSD is now viewable on the video monitor. The system configuration main

menu appears when the video format and video signals between the Home Theater

Standard and your video monitor are compatible.

If you have any questions regarding the selection of the video format, please call your

authorized Krell dealer, distributor, or Krell.

AN INTRODUCTION TO SYSTEM SETUP

The Home Theater Standard provides a variety of connection and operation options for

outstanding music and cinema soundtrack reproduction. To take full advantage of the

features the Home Theater Standard offers, you’ll need to set up your system in this

order:

1, Connect your Home Theater Standard to the desired analog and digital audio

sources, video sources, and amplifiers. See Connecting the Home Theater

Standard to Your System, on page 23.

2. Configure your Home Theater Standard’s speaker volume, input devices, and trims

using the built-in, easy-to-follow System Setup and Configuration menus. Step-by-

step instructions begin on page 26, System Setup and Configuration.

3. Review the Front Panel, Back Panel, and Remote Control descriptions for information

on input, zone, and mode selections, speaker adjustment, input and output

connections for analog, digital, and video sources, and remote control operation. See

pages 7-22 for illustrations and descriptions.

After you’ve connected and configured your Home Theater Standard and know its basic

features, you’re ready to go. See Operating the Home Theater Standard, on page 53.

6

Krell Home Theater Standard

Figure 1 The Home Theater Standard Front Panel

10 5 11 6

I

--00

-C) "©

12 7 13 8 14 9

SAT VOR

-00 --00

AUX1 AUX2

----00

15 16

STAND-BY

POWER

-----0

3 2

HTS

Basic Operation

1 Power Button

2 Power LED

3 Stand-by LED

4 Infrared Sensor

Input Device Selection

Buttons and LEDs

5 DVD Button and LEDs

6 LD Button and LEDs

7 SAT Button and LEDs

8 VCR1 Button and LEDs

9 TV Button and LEDs

ZONE

00----

22

18 19

Home Theater Standard

USER

23 29

24

STEREO MUSlO1

--0 ----O

25 26 30

10 CD Button and LEDs

11 Tuner Button and LEDs

12 Auxl Button and LEDs

13 Aux2 Button and LEDs

14 TapeNCR2 Button and LEDs

15 Main Zone and Zone 2 Button

16 Main Zone and Zone 2 LEDs

17 Infrared Emitter

Processing Mode Buttons and LEDs

18 Stereo Button and LED

19 Music1 Button and LED

20 Music2 Button and LED

21 Pro Logic Button and LED

22 Preamp Button and LED

23 Front Panel Display

24

User Button

25 Balance Button

Individual Channel Buttons

26 Center Button

27 Rear Button

28 Sub Button

29 Save Button

30 Level Down and Up Buttons

31 Recall Button

20

21

MUSICB PRO LOGIC

---O

O--

27 28

Front Panel Description

See Figure 1 on page 7

The Home Theater Standard front panel provides power on and off; input, zone, and

processing mode selection; monitoring and display of processor status; and balance

and volume control. The front panel components are described below.

Basic Operation

1 Power Button

The power button switches the Home Video Standard from the stand-by to the

operational mode.

Note

When you power off while zone 2 is se/ected, on/y zone 2 turns off. Press the power

button or HTS key a second time to power off the main zone.

2 Power LED

The blue power LED illuminates when the Home Theater Standard is in the operational

mode.

3 Stand-by LED

The red stand-by LED illuminates when the back panel power switch (54) is on,

indicating that the Home Theater Standard is in stand-by mode. Krell recommends that

the back panel power switch remain in the up position at all times.

4 Infrared Sensor

The infrared sensor receives commands from the Home Theater Standard remote

control. For proper remote control operation, make sure the infrared sensor is not

covered or obstructed.

Input Device Selection Buttons and LEDs

When properly configured, the Home Theater Standard keeps track of each device and

its associated connections. For example, DVD uses Coax1 for digital audio, Composite1

for video, and S-1 for analog audio. The Home Theater Standard automatically engages

the correct inputs when you press a front panel device selection button.

The Home Theater Standard is equipped with the following input selections, which allow

you to select the device connected to your Home Theater Standard. Above each device

are two LEDs: one red and one green. The red LED illuminates when the input is

engaged and playing in the main zone. The green LEE) illuminates when the input is

engaged and playing in zone 2.

5 DVD Button and LEDs

Use this button to select the digital videodisc device.

8 Krell Home Theater Standard

Front Panel Description, continued

6 LD Button and LEDs

Use this button to select the laser disc device.

7 SAT Button and LEDs

Use this button to select the satellite feed device.

8 VCR1 Button and LEDs

Use this button to select the VCR device.

9 TV Button and LEDs

Use this button to select the television device.

10 CD Button and LEDs

Use this button to select the compact disc device.

11 Tuner Button and LEDs

Use this button to select the AM/FM tuner device.

12 Auxl Button and LEDs

Use this button to select an auxiliary device, such as phono, tape, or an additional DVD,

LD, CD, or VCR.

13 Aux2 Button and LEDs

Use this button to select a second auxiliary device, such as phono, tape, or an

additional DVD, LD, CD, or VCR.

14 Tape/VCR2 Button and LEDs

Use this button to playback pre-recorded tapes. You may also use this button to

compare the output signal of an analog tape recorder to an audio source. See Tape

Input and Output, on page 53.

15 Main Zone and Zone 2 Button

Use this button to select either main zone or zone 2 device control. See Main Zone and

Zone 2 Operation, on page 54.

16 Main Zone and Zone 2 LEDs

The Home Theater Standard has two zone device controls, main or zone 2. Above each

device are two LEDs: one red and one green. The red LED illuminates when the input is

engaged and playing in the main zone. The green LED illuminates when the input is

engaged and playing in zone 2.

Krell Home Theater Standard

9

Front Panel Description, continued

17 Infrared Emitter

Emits the Home Theater Standard remote operation code to a learning remote, which

can be programmed to operate the Home Theater Standard. See Program Remote, on

page 48.

Processing Mode Buttons and LED$

18 Stereo Button and LED

Use this button to select the stereo decoding mode, which allows you to listen to a

stereo recording in two channel (left and right) mode. The red LED illuminates when this

mode is activated.

Note

The stereo decoding mode operates only with an analog input or a digital PCM input (for

example, a compact disc).

19 Music1 Button and LED

20 Music2 Button and LED

Use these buttons to engage Krell Music Surround mode. This music-decoding mode

allows you to listen to a stereo recording in a multi-channel mode. This mode can also

be programmed to create different simulated acoustic environments. The red LED

illuminates when this circuitry is engaged. See Configure Music, on page 47.

Note

The Krell Music Surround decoding mode operates only with an analog input or a digital

PCM input (for example, a compact disc).

21 Pro Logic Button and LED

Use this button to engage Dolby Pro Logic circuitry for use with all Dolby Surround

encoded material, including laser discs, videotapes, television broadcasts, and compact

discs. The red LED illuminates when the Home Theater Standard is in the Dolby Pro

Logic decoding mode.

Note

This mode is selected automatically if Do/by Digital source material is encoded for Pro

Logic. If you wish to turn off this mode, press the Pro Logic button.

22 Preamp Button and LED

Use this button to send the signal from the analog input directly to the volume control,

with no digital processing, using the analog stage of the preamp. This avoids possible

digital signal degradation and can be used for components with a high quality signal

such as the KPS 28c. See Configure Mode, on page 36, for information on assigning

the analog input to one of the device buttons (DVD, LD, SAT, VCR, TV).

10

Krell Home Theater Standard

Front Panel Description, continued

23 Front Panel Display

The front panel display provides status messages for Home Theater Standard

operations, including volume and balance level, decoding mode, and zone information.

In addition, when a new device is selected, the physical inputs are displayed. The

display turns off after five seconds of inactivity.

24 User Button

Use this programmable button to select one of three available dynamic range

compression modes: normal (11 dB), max(imum) (no compression), or night (22

See User Button Setup, on page 50. In addition, the user button can be deactivated.

25 Balance Button

Press this button to adjust the main left/right speaker balance. This button converts the

volume level controls to balance controls. BAL 0 in the front panel display window

indicates the center position. Balance may be adjusted in .5 dB increments, up to 6 dB.

Balance levels are shown numerically on the front panel display. The balance level

buttons revert to their original functions as main volume level controls after three

seconds of inactivity.

Individual Channel Buttons

Use the Center, Rear, and Sub buttons to change taste trims (make temporary speaker

output adjustments of +/- 10 dB). These temporary changes revert to 0 dB when a new

device is selected or the system is powered down. For more information on taste trims

and master (programmable) trims, see Configure Level Adjustment, on page 39.

26 Center Button

Press the center button, then use the level up and down buttons (30) to adjust the

center speaker volume.

27 Rear Button

Press the rear button, then use the level up and down buttons (30) to adjust the rear

speaker volume.

28 Sub Button

Press the sub (subwoofer) button, then use the level up and down buttons (30) to adjust

the subwoofer speaker volume.

29 Save Button

Use this button to save system configuration settings and during learning remote

programming. See Saving Setup, Recalling Setup, and Restoring Factory Default

System Configuration Settings, on page 52, and Program Remote, on page 48.

Krell Home Theater Standard 11

Front Panel Description, continued

30 Level Down and Up Buttons

Use the volume level buttons to adjust the output for the entire system as well as

balance and individual levels for the center speaker, rear speakers, and subwoofers.

The volume level is shown in the front panel display. See System Setup and

Configuration, on page 26.

31 Recall Button

Use this button to recall previously stored system configuration settings. See Saving

Setup, Recalling Setup, and Restoring Factory Default System Configuration

Settings, on page 52.

12 Krell Home Theater Standard

Figure 2 The Home Theater Standard Back Panel

32

33 34

35

RIQH’I" LEFT

39 40 37 36

DIQITAL AUDIO

INPUTS

42 45

Analog Audio Outputs and Inputs

32

Balanced Analog Audio Outputs

33 Single-ended Analog Audio Outputs

34

Multi-Channel Audio Output Connector

35 B-1 Left and B-1 Right Inputs

36

Tape In Left and Right

37 Tape Out Left and Right

38

VCR1 In Left and Right

39

VCR1 Out Left and Right

40 Zone 2 Out Left and Right

41 S-1, S-2, S-3, S-4, S-5 Left and Right Inputs

41 44 43 47 49

Digital Audio Inputs and Outputs

42 Digital Optical Inputs

43 Digital Audio Inputs

44 Digital Audio Outputs

Video Inputs and Outputs

45 S-video Outputs

46 S-video Inputs

47 Composite Video Outputs

48 Composite ~/ideo Inputs

49 Component Video Outputs

50 Component Video Inputs

46

51

52

o

0 o

oOO

50 48

54 55

Remote Control

51 RS-232 Remote or

Optional PHAST Link Connector

52 RC-5 In

53 12 VDC Out and In

Power

54 Back Panel Power Switch

55 IEC Connector

53

Back Panel Description

See Figure 2 on page 13

The back panel of the Home Theater Standard provides all input and output

connections, remote control inputs and outputs, power on and off, and power

connection. The back panel functions are described below.

Analog Audio Outputs and Inputs

32 Balanced Analog Audio Outputs

The Home Theater Standard is equipped with six balanced analog audio channel

outputs, with XLR connectors, for the left, center, right, left rear, right rear, and

subwoofer.

33 Single-ended Analog Audio Outputs

The Home Theater Standard is equipped with six single-ended analog audio channel

outputs, with RCA connectors, for the left, center, right, left rear, right rear, and

subwoofer.

34 Multi-Channel Audio Output Connector

The Home Theater Standard is equipped with a multi-channel audio output, with a DB-

25 connector, which contains the output connections for all the output channels (left,

center, right, left rear, right rear, and subwoofer).

35 B-1 Left and Right Inputs

The Home Theater Standard is equipped with one set of balanced inputs with

connectors.

The XLR pin configurations are as follows:

Pin 1: Shield (ground)

Pin 2: Non-inverting (0

°)

Pin 3: Inverting (180

°

)

36 Tape In Left and Right

The Home Theater Standard is equipped with one set of single-ended tape inputs with

RCA connectors.

37 Tape Out Left and Right

The Home Theater Standard is equipped with one set of single-ended tape outputs with

RCA connectors.

38 VCR1 In Left and Right

The Home Theater Standard is equipped with one set of single-ended inputs with RCA

connectors, for a VCR audio source.

14 Krell Home Theater Standard

Back Panel Description, continued

39 VCR1 Out Left and Right

The Home Theater Standard is equipped with one set of single-ended outputs with RCA

connectors, for a VCR audio source.

40 Zone 2 Out Left and Right

The Home Theater Standard is equipped with one set of single-ended zone 2 audio

outputs with RCA connectors.

41 S-l, S-2, S-3, S-4, S-5 Left and Right Inputs

The Home Theater Standard is equipped with five sets of single-ended audio inputs with

RCA connectors.

Digital Audio Inputs and Outputs

42 Digital Optical Inputs

The Home Theater Standard is equipped with two digital EIAJ optical inputs with

TosLink connectors.

43 Digital Audio Inputs

The Home Theater Standard is equipped with six coaxial digital audio inputs with RCA

connectors.

44 Digital Audio Outputs

The Home Theater Standard is equipped with two digital audio outputs: one coaxial with

an RCA connector, and one EIAJ optical with a TosLink connector.

Video Inputs and Outputs

45 S-video Outputs

The Home Theater Standard is equipped with two S-video outputs with DIN connectors.

The main S-video output (labeled OSD on back panel) includes on-screen display. For

dubbing purposes, the second S-video output does not include on-screen display.

Note

The OSD and non-OSD outputs are not interchangeable.

46 S-video Inputs

The Home Theater Standard is equipped with four S-video inputs with DIN connectors.

47 Composite Video Outputs

The Home Theater Standard is equipped with two composite video outputs with RCA

connectors. The main composite video output (labeled OSD on back panel) includes on-

screen display. For dubbing purposes, the second composite video output does not

include on-screen display.

Krell Home Theater Standard 15

48 Composite Video Inputs

The Home Theater Standard is equipped with four RCA composite video inputs with

RCA connectors.

49 Component Video Outputs

The Home Theater Standard is equipped with one set of component video outputs with

RCA connectors. Component video uses three wires (labeled Y, Cr, and Cb on back

panel) to convey the video signal, including the OSD.

50 Component Video Inputs

The Home Theater Standard is equipped with two sets of component video inputs.

Remote Control

51 RS-232 Remote or Optional PHAST Link Connector

The Home Theater Standard is equipped with an RS-232 port, which receives

messages from a computer based control system, providing more intelligent control of

the Home Theater Standard. For more information, see RS-232 Port: Sending

Commands and Interpreting Data, developer’s reference shipped with the Home

Theater Standard.

The Home Theater Standard may be outfitted with an optional PHAST Link connector

instead of an RS-232 connector, for integrating the HTS within a PHAST system.

Contact your authorized Krell dealer, distributor, or Krell for information about this

connection option.

52 RC-5 In

The RC-5 input makes custom installation easy and secure by accepting baseband

RC-5 input commands from hardwired remote controllers.

53 12 VDC Out and In

The 12 VDC output sends a 12 Volt power on/off signal to other Krell components via a

12 V trigger cable, as well as to other devices that incorporate 12 Volt power on/off

trigger input. The Home Theater Standard has four programmable 12 Volt outputs:

Out1, Out2, Out3, and Out4; one input is available.

Note

When the HTS is in the operational mode, the 12 VDC Out provides 12 V of DC output.

When the HTS is in the stand-by mode or off, the DC output is 0 V.

Power

54 Back Panel Power Switch

Use this switch to change the Home Theater Standard from off to stand-by.

55 lEO Connector

The Home Theater Standard is equipped with a standard female IEC power connector,

for use with the AC power cord.

16 Krell Home Theater Standard

Page is loading ...

Krell Industries HTS 2 User manual

This manual is also suitable for

Krell Industries HTS 2 User manual

Related papers

Other documents