Danfoss Low Harmonic Drive FC 300 Operating instructions

Contents

1 How to Read this Instruction Manual

1-1

Copyright, Limitation of Liability and Revision Rights 1-1

Approvals 1-2

Symbols 1-2

2 Safety

2-1

General Warning 2-2

Before Commencing Repair Work 2-2

Special conditions 2-2

Avoid unintended start 2-3

Safe Stop Installation 2-3

Safe Stop of the Adjustable Frequency Drive 2-5

IT Line Power 2-6

3 Introduction to the Low Harmonic Drive

3-1

Working Principle 3-1

IEEE519 Compliance 3-2

Ordering Form Type Code 3-3

4 How to Install

4-1

How to Get Started 4-1

Pre-installation 4-2

Planning the Installation Site 4-2

Receiving the Adjustable Frequency Drive 4-2

Transportation and Unpacking 4-2

Lifting 4-3

Mechanical Dimensions 4-6

Mechanical Installation 4-12

Assembly of F Frame Sections 4-14

Control Wire Connection between Drive and Filter 4-17

Terminal Locations - Frame size D 4-18

Terminal Locations - Frame size E 4-19

Terminal Locations - Frame size F 4-21

Cooling and Airflow 4-23

Field Installation of Options 4-30

Installation of Input Plate Options 4-30

Installation of Line Power Shield for Adjustable Frequency Drives 4-30

Frame size F Panel Options 4-31

VLT Automation Low Harmonic Drive Instruc-

tion Manual

Contents

MG.34.O1.22 - VLT

®

is a registered Danfoss trademark

Electrical Installation 4-33

Power Connections 4-33

AC line input connections 4-46

Power and Control Wiring for Non-shielded Cables 4-47

Fuses 4-48

Control Cable Routing 4-52

Electrical Installation, Control Terminals 4-53

Connection Examples for Control of Motor with External Signal Provider 4-54

Start/Stop 4-54

Pulse Start/Stop 4-55

Electrical Installation - additional 4-57

Electrical Installation, Control Cables 4-57

Switches S201, S202, and S801 4-59

Final Set-up and Test 4-60

Additional Connections 4-62

Mechanical Brake Control 4-62

Motor Thermal Protection 4-63

5 How to Operate the Low Harmonic Drive

5-1

How to operate the Graphical LCP (GLCP) 5-1

6 How to Program the Low Harmonic Drive

6-1

How to Program the Adjustable Frequency Drive 6-1

Quick Set-up Parameters 6-1

Basic Set-up Parameters 6-5

How to Program the Active Filter 6-29

Using the Low Harmonic Drive in NPN Mode 6-29

Parameter Lists - Adjustable Frequency Drive 6-30

Parameter Lists - Active Filter

6-52

Operation/Display 0-** 6-52

Digital In/Out 5-** 6-53

Comm. and Options 8-** 6-53

Special Functions 14-** 6-54

FC Information 15-** 6-55

Data Readouts 16-** 6-56

AF Settings 300-** 6-56

AF Readouts301-** 6-57

7 RS-485 Installation and Set-up

7-1

Contents

VLT Automation Low Harmonic Drive Instruc-

tion Manual

MG.34.O1.22 - VLT

®

is a registered Danfoss trademark

Network Configuration 7-3

FC Protocol Message Framing Structure 7-4

Examples 7-9

How to Access Parameters 7-10

8 General Specifications

8-1

Filter Specifications

8-8

9 Troubleshooting

9-1

Alarms and Warnings - Adjustable Frequency Drive (right LCP) 9-1

Warnings/Alarm Messages 9-1

Alarms and Warnings - Filter (left LCP) 9-11

10 Index

10-1

VLT Automation Low Harmonic Drive Instruc-

tion Manual

Contents

MG.34.O1.22 - VLT

®

is a registered Danfoss trademark

Contents

VLT Automation Low Harmonic Drive Instruc-

tion Manual

MG.34.O1.22 - VLT

®

is a registered Danfoss trademark

1 How to Read this Instruction Manual

1.1.1 Copyright, Limitation of Liability and Revision Rights

This publication contains information proprietary to Danfoss. By accepting and using this manual, the user agrees that the information contained herein

will be used solely for operating equipment from Danfoss or equipment from other vendors provided that such equipment is intended for communication

with Danfoss equipment over a serial communication link. This publication is protected under the copyright laws of Denmark and most other countries.

Danfoss does not warrant that a software program produced according to the guidelines provided in this manual will function properly in every physical,

hardware or software environment.

Although Danfoss has tested and reviewed the documentation within this manual, Danfoss makes no warranty or representation, neither expressed nor

implied, with respect to this documentation, including its quality, performance, or fitness for a particular purpose.

In no event shall Danfoss be liable for direct, indirect, special, incidental, or consequential damages arising out of the use, or the inability to use information

contained in this manual, even if advised of the possibility of such damages. In particular, Danfoss is not responsible for any costs, including but not

limited to those incurred as a result of lost profits or revenue, loss or damage of equipment, loss of computer programs, loss of data, the costs to substitute

these, or any claims by third parties.

Danfoss reserves the right to revise this publication at any time and to make changes to its contents without prior notice or any obligation to notify former

or present users of such revisions or changes.

1.1.2 Available Literature for VLT AutomationDrive

- The VLT AutomationDrive Instruction Manual - High Power, MG.33.UX.YY provides the necessary information for getting the drive up and running.

- The VLT AutomationDrive Design Guide MG.33.BX.YY contains all technical information about the drive and customer design and applications.

- The VLT AutomationDrive Programming Guide MG.33.MX.YY provides information on how to program and includes complete parameter de-

scriptions.

- The VLT AutomationDrive Profibus Instruction Manual MG.33.CX.YY provides the information required for controlling, monitoring and program-

ming the drive via a Profibus serial communication bus.

- The VLT AutomationDrive DeviceNet Instruction Manual MG.33.DX.YY provides the information required for controlling, monitoring and pro-

gramming the drive via a DeviceNet serial communication bus.

X = Revision number

YY = Language code

Danfoss technical literature is also available online at www.danfoss.com/drives.

VLT Automation Low Harmonic Drive Instruc-

tion Manual

1 How to Read this Instruction Manual

MG.34.O1.22 - VLT

®

is a registered Danfoss trademark

1-1

1

VLT AutomationDrive

Instruction Manual

Software version: 5.9x

This Instruction Manual can be used for all VLT Automation Low Harmonic Drive adjustable frequency drives with software version 5.9x.

The software version number can be seen from par. 15-43

Software Version

.

NOTE!

The Low Harmonic Drive has two LCPs, one for the adjustable frequency drive (to the right) and one for the active filter (to the left).

Each LCP controls only the unit it is connected to and there is no communication between the two LCPs.

1.1.3 Approvals

1.1.4 Symbols

Symbols used in this Instruction Manual.

NOTE!

Indicates something to be noted by the reader.

Indicates a general warning.

Indicates a high-voltage warning.

* Indicates a default setting

1 How to Read this Instruction Manual

VLT Automation Low Harmonic Drive Instruc-

tion Manual

1-2

MG.34.O1.22 - VLT

®

is a registered Danfoss trademark

1

2Safety

2.1.1 Safety note

The voltage of the adjustable frequency drive is dangerous whenever connected to line power. Incorrect installation of the motor,

adjustable frequency drive or serial communication bus may cause damage to the equipment, serious personal injury or death. Con-

sequently, the instructions in this manual, as well as national and local rules and safety regulations, must be complied with.

Safety Regulations

1. The adjustable frequency drive must be disconnected from line power if repair work is to be carried out. Make sure that the line power supply

has been disconnected and that the necessary time has passed before removing motor and line power plugs.

2. The [STOP/RESET] key on the control panel of the adjustable frequency drive does not disconnect the equipment from line power and is thus

not to be used as a safety switch.

3. Correct protective grounding of the equipment must be established, the user must be protected against supply voltage, and the motor must be

protected against overload in accordance with applicable national and local regulations.

4. The ground leakage currents are higher than 3.5 mA.

5. Protection against motor overload is set by par. 1-90

Motor Thermal Protection

. If this function is desired, set par. 1-90 to data value [ETR trip]

(default value) or data value [ETR warning]. Note: The function is initialized at 1.16 x rated motor current and rated motor frequency. For the

North American market: The ETR functions provide class 20 motor overload protection in accordance with NEC.

6. Do not remove the plugs for the motor and line power supply while the adjustable frequency drive is connected to line power. Make sure that

the line power supply has been disconnected and that the necessary time has passed before removing motor and line power plugs.

7. Please note that the adjustable frequency drive has more voltage inputs than L1, L2 and L3 when load sharing (linking of the DC intermediate

circuit) and external 24 V DC have been installed. Make sure that all voltage inputs have been disconnected and that the necessary time has

passed before commencing repair work.

Installation at High Altitudes

Installation at high altitude:

At altitudes above 9843 ft [3 km], please contact Danfoss Drives regarding PELV.

Warning against Unintended Start

1. The motor can be brought to a stop by means of digital commands, bus commands, references or a local stop, while the adjustable frequency drive

is connected to line power. If personal safety considerations make it necessary to ensure that no unintended start occurs, these stop functions are not

sufficient. 2. While parameters are being changed, the motor may start. Consequently, the stop key [RESET] must always be activated; following which

data can be modified. 3. A motor that has been stopped may start if faults occur in the electronics of the adjustable frequency drive, or if a temporary

overload or a fault in the supply line power or the motor connection ceases.

Warning:

Touching the electrical parts may be fatal - even after the equipment has been disconnected from line power.

Also make sure that other voltage inputs have been disconnected, such as external 24 V DC, load sharing (linkage of DC intermediate circuit), as well as

the motor connection for kinetic backup.

VLT Automation Low Harmonic Drive Instruc-

tion Manual

2 Safety

MG.34.O1.22 - VLT

®

is a registered Danfoss trademark

2-1

2

2.1.2 General Warning

Warning:

Touching the electrical parts may be fatal - even after the equipment has been disconnected from line power.

Also make sure that other voltage inputs have been disconnected, (linkage of DC intermediate circuit), as well as the motor connection

for kinetic backup.

Before touching any potentially live parts of the adjustable frequency drive, wait at least as follows:

380–480 V, 175–275 hp [132–200 kW], wait at least 20 minutes.

380–480 V, 350–850 hp [250–630 kW], wait at least 40 minutes.

Shorter time is allowed only if indicated on the nameplate for the specific unit. Be aware that there may be high voltage on the DC

links even when the control card LEDs are turned off. A red LED is mounted on a circuit board inside both the drive and the active filter

to indicate the DC bus voltages. The red LED will stay lit until the DC link is 50 VDC or lower.

Leakage Current

The ground leakage current from the adjustable frequency drive exceeds 3.5 mA. According to IEC 61800-5-1, a reinforced protective

ground connection must be ensured by means of: a min. 0.015 in² [10 mm²] Cu or 0.025 in² [16 mm²] Al PE wire or an additional PE

wire - with the same cable cross-section as the line power wiring - must be terminated separately.

Residual Current Device

This product can cause DC current in the protective conductor. Where a residual current device (RCD) is used for extra protection, only

an RCD of Type B (time delayed) shall be used on the supply side of this product. See also RCD Application Note MN.90.GX.02.

Protective grounding of the adjustable frequency drive and the use of RCDs must always follow national and local regulations.

2.1.3 Before Commencing Repair Work

1. Disconnect the adjustable frequency drive from line power.

2. Disconnect DC bus terminals 88 and 89

3. Wait at least the time mentioned above in the section General Warning.

4. Remove motor cable

2.1.4 Special conditions

Electrical ratings:

The rating indicated on the nameplate of the adjustable frequency drive is based on a typical 3-phase line power supply within the specified voltage,

current and temperature ranges, which are expected to be used in most applications.

The adjustable frequency drives also support other special applications, which affect the electrical ratings of the adjustable frequency

drive. Special conditions that affect the electrical ratings might be:

• Single phase applications.

• High temperature applications which require derating of the electrical ratings

• Marine applications with more severe environmental conditions.

Consult the relevant clauses in these instructions and in the Design Guide for information about the electrical ratings.

2 Safety

VLT Automation Low Harmonic Drive Instruc-

tion Manual

2-2

MG.34.O1.22 - VLT

®

is a registered Danfoss trademark

2

Installation requirements:

The overall electrical safety of the adjustable frequency drive requires special installation considerations regarding:

• Fuses and circuit breakers for overcurrent and short-circuit protection

• Selection of power cables (line power, motor, brake, load sharing and relay)

• Grid configuration (IT,TN, grounded leg, etc.)

• Safety of low-voltage ports (PELV conditions).

Consult the relevant clauses in these instructions and in the Design Guide for information about the installation requirements.

2.1.5 Avoid unintended start

While the adjustable frequency drive is connected to line power, the motor can be started/stopped using digital commands, bus com-

mands, references or via the Local Control Panel.

• Disconnect the adjustable frequency drive from line power whenever personal safety considerations make it necessary to

avoid an unintended start.

• To avoid unintended start, always activate the [OFF] key before changing parameters.

• Unless terminal 37 is turned off, an electronic fault, temporary overload, a fault in the line power supply, or lost motor

connection may cause a stopped motor to start.

2.1.6 Safe Stop Installation

To carry out an installation of a Category 0 Stop (EN60204) in

conformity with Safety Category 3 (EN954-1), follow these in-

structions:

1. The bridge (jumper) between Terminal 37 and 24 V DC must be

removed. Cutting or breaking the jumper is not sufficient. Re-

move it entirely to avoid short-circuiting. See jumper in figure.

2. Connect terminal 37 to 24 V DC by a short circuit-protected ca-

ble. The 24 V DC voltage supply must be interruptible by an

EN954-1 category 3 circuit interrupt device. If the interrupt de-

vice and the adjustable frequency drive are placed in the same

installation panel, you can use a non-shielded cable instead of

a shielded one.

Figure 2.1: Bridge jumper between terminal 37 and 24 VDC

The figure below shows a Stopping Category 0 (EN 60204-1) with safety Category 3 (EN 954-1). The circuit interruption is caused by an opening door

contact. The figure also shows how to connect a non-safety-related hardware coast.

VLT Automation Low Harmonic Drive Instruc-

tion Manual

2 Safety

MG.34.O1.22 - VLT

®

is a registered Danfoss trademark

2-3

2

Figure 2.2: Figure of the essential aspects of an installation to achieve a Stopping Category 0 (EN 60204-1) with safety Category 3 (EN

954-1).

2 Safety

VLT Automation Low Harmonic Drive Instruc-

tion Manual

2-4

MG.34.O1.22 - VLT

®

is a registered Danfoss trademark

2

2.1.7 Safe Stop of the Adjustable Frequency Drive

For versions fitted with a Safe Stop terminal 37 input, the adjustable frequency drive can perform the safety function

Safe Torque Off

(As defined by

draft CD IEC 61800-5-2) or

Stop Category 0

(as defined in EN 60204-1).

It is designed and approved suitable for the requirements of Safety Category 3 in EN 954-1. This functionality is called Safe Stop. Prior to integration and

use of Safe Stop in an installation, a thorough risk analysis on the installation must be carried out in order to determine whether the Safe Stop functionality

and safety category are appropriate and sufficient. In order to install and use the Safe Stop function in accordance with the requirements of Safety

Category 3 in EN 954-1, the related information and instructions of the

Design Guide

must be followed. The information and instructions of the Instruction

Manual are not sufficient for a correct and safe use of the safe stop functionality.

VLT Automation Low Harmonic Drive Instruc-

tion Manual

2 Safety

MG.34.O1.22 - VLT

®

is a registered Danfoss trademark

2-5

2

2.1.8 IT Line Power

IT line power

Do not connect adjustable frequency drives with RFI filters to line power supplies with a voltage between phase and ground of more

than 440 V for 400 Vs and 760 V for 690 V drives.

For 400 V IT line power and delta ground (grounded leg), AC line voltage may exceed 440 V between phase and ground.

Par. 14-50

RFI filter

can be used to disconnect the internal RFI capacitors from the RFI filter to ground. Par. 14-50

RFI filter

on both the drive and the

filter must be turned off.

2.1.9 Disposal Instructions

Equipment containing electrical components may not be disposed of together with domestic waste.

It must be separately collected with electrical and electronic waste according to local and currently valid leg-

islation.

2 Safety

VLT Automation Low Harmonic Drive Instruc-

tion Manual

2-6

MG.34.O1.22 - VLT

®

is a registered Danfoss trademark

2

3 Introduction to the Low Harmonic Drive

3.1.1 Working Principle

The VLT Low Harmonic Drive is a VLT High Power adjustable frequency drive with an integrated active filter. An active filter is a device that actively

monitors harmonic distortion levels and injects compensative harmonic current onto the line to cancel out the harmonics.

Figure 3.1: Basic layout for the Low Harmonic Drive

VLT Automation Low Harmonic Drive Instruc-

tion Manual

3 Introduction to the Low Harmonic Drive

MG.34.O1.22 - VLT

®

is a registered Danfoss trademark

3-1

3

3.1.2 IEEE519 Compliance

Low harmonic drives are designed to draw an ideal sinusoidal current waveform from the supply grid with a power factor of 1. Where traditional non-

linear load draws pulse-shaped currents, the low harmonic drive compensates for this via the parallel filter path which lowers the stress on the supply

grid. The low harmonic drive meets the toughest harmonic standards and has a THiD of less then 5% at full load for <3% pre-distortion on a balanced

three-phased grid. The unit is designed to meet IEEE519 recommendations for Isc/Il >20 for both uneven and even individual harmonic levels. The filter

portion of a low harmonic drive has a progressive switching frequency which leads to a wide frequency spreads producing lower individual harmonic levels

above the 50th.

Figure 3.2: Typical harmonic frequency spectrum and THD value at the line power terminals of the drive

n = harmonic order

⃟.....IEEE519 (Isc/IL>20) limits for individual harmonics

3 Introduction to the Low Harmonic Drive

VLT Automation Low Harmonic Drive Instruc-

tion Manual

3-2

MG.34.O1.22 - VLT

®

is a registered Danfoss trademark

3

3.1.3 Ordering Form Type Code

It is possible to design a VLT Low Harmonic Drive according to the application requirements by using the ordering number system.

Product groups

1-3

Adjustable frequency

drive series

4-6

Power rating

8-10

Phases

11

AC Line Voltage

12

Enclosure

13-15

Enclosure type

Enclosure class

Control supply volt-

age

Hardware configu-

ration

RFI filter

16-17

Brake

18

Display (LCP)

19

Coating PCB

20

Line power option

21

Adaptation A

22

Adaptation B

23

Software release

24-27

Software language

28

A options

29-30

B options

31-32

C0 options, MCO

33-34

C1 options

35

C option software

36-37

D options

38-39

To order a VLT Low Harmonic Drive, type the letter “L” in position 16 of

the type code string. Not all choices/options are available for each ad-

justable frequency drive variant. To verify if the appropriate version is

available, please consult the Drive Configurator on the Internet. For more

information on the options available, please see the

Design Guide

.

VLT Automation Low Harmonic Drive Instruc-

tion Manual

3 Introduction to the Low Harmonic Drive

MG.34.O1.22 - VLT

®

is a registered Danfoss trademark

3-3

3

3 Introduction to the Low Harmonic Drive

VLT Automation Low Harmonic Drive Instruc-

tion Manual

3-4

MG.34.O1.22 - VLT

®

is a registered Danfoss trademark

3

4How to Install

4.1 How to Get Started

4.1.1 About How to Install

This chapter covers mechanical and electrical installations to and from power terminals and control card terminals.

Electrical installation of

options

is described in the relevant Instruction Manual and Design Guide.

4.1.2 How to Get Started

The adjustable frequency drive is designed for quick installation and is EMC-compliant. Just follow the steps described below.

Read the safety instructions before installing the unit.

Failure to follow recommendations could result in death or serious injury.

Mechanical Installation

• Mechanical mounting

Electrical Installation

• Connection to Line and Protecting Ground

• Motor connection and cables

• Fuses and circuit breakers

• Control terminals - cables

Quick Setup

• Local Control Panel (LCP) of adjustable frequency drive

• Local Control Panel of filter

• Automatic Motor Adaptation, AMA

• Programming

Frame size is depending on enclosure type, power range and AC line

voltage

Figure 4.1: Diagram showing basic installation including line

power, motor, start/stop key, and potentiometer for speed

adjustment.

VLT Automation Low Harmonic Drive Instruc-

tion Manual

4 How to Install

MG.34.O1.22 - VLT

®

is a registered Danfoss trademark

4-1

4

4.2 Pre-installation

4.2.1 Planning the Installation Site

NOTE!

Before performing the installation, it is important to plan the installation of the adjustable frequency drive. Neglecting this may result

in extra work during and after installation.

Select the best possible operation site by considering the following (see details on the following pages and in the respective Design

Guides):

• Ambient operating temperature

• Installation method

• How to cool the unit

• Position of the adjustable frequency drive.

•Cable routing

• Ensure the power source supplies the correct voltage and necessary current.

• Ensure that the motor current rating is within the maximum current from the adjustable frequency drive.

• If the adjustable frequency drive is without built-in fuses, ensure that the external fuses are rated correctly.

4.2.2 Receiving the Adjustable Frequency Drive

When receiving the adjustable frequency drive, make sure that the packaging is intact, and look for any damage that might have occurred to the unit

during transport. If damage has occurred, immediately contact the shipping company to make a damage claim.

4.2.3 Transportation and Unpacking

Before unpacking the adjustable frequency drive, it is recommended to unload it as close as possible to the final installation site.

Remove the box and handle the adjustable frequency drive on the pallet, as long as possible.

4 How to Install

VLT Automation Low Harmonic Drive Instruc-

tion Manual

4-2

MG.34.O1.22 - VLT

®

is a registered Danfoss trademark

4

4.2.4 Lifting

Always lift the adjustable frequency drive using the dedicated lifting holes. For all D and E frames, use a bar to avoid bending the lifting holes of the

adjustable frequency drive.

Figure 4.2: Recommended lifting method, frame sizes D and E.

The lifting bar must be able to handle the weight of the adjustable frequency drive. See

Mechanical Dimensions

for the weight of the

different frame sizes. Maximum diameter for bar is 1 in [2.5 cm]. The angle from the top of the drive to the lifting cable should be

60° or greater.

VLT Automation Low Harmonic Drive Instruc-

tion Manual

4 How to Install

MG.34.O1.22 - VLT

®