fortessa Digital 2 Wire Door Entry User manual

DIGI2 SYSTEM

TECHNICAL MANUAL

TM

Instructions:

• Install the equipment by carefully following the instructions given by the manufacturer and in compliance with the legislation in force.

• All the equipment must only be used for the purpose it was built for Fortessa declines any responsibility for improper use of the

apparatus, for modifications made by others under any title or scope, and for the use of accessories and materials which are not

the original ones.

• All the products comply with the requirements of the 2006/95/CE directives (which replace the 73/23/CEE directives and the

successive amendments). This is proved by the CE mark on the products.

• Do not run the riser wires in proximity of the power supply cables (230/400V).

TM

1

TM

SUMMARY

•

EXTERNAL UNITS

- Instructions for installing external audio-video unit

standard pag. 2

- Instructions for assembling an informative module

FT3326, FT3344 and FT3346 pag. 4

- Creating unit standard name tags pag. 4

- Digital call FT3340 pag. 5

- Electronic name directory module FT3342 pag. 11

- Instructions for installing external audio-video unit

vandal resistant pag. 14

- Digital call module FT3070/A pag. 17

- Electronic name directory module FT3072/A pag. 22

- Standard combined access FT3328 and vandal combined

access FT3188 electronic digital key pag. 26

- Access control standard lock FT3335

and vandal resistant lock FT3195 pag. 29

•

INTERNAL UNITS

- Description of the monitor Genius and user information pag. 32

- Instructions for installation of the internal unit Genius pag. 33

- Technical characteristics of bracket FT5714

for Genius monitor pag. 35

- Digi2 wall telephone for mixed systems FT2428W/A pag. 36

- Instructions to install telephone FT2428W/A pag. 36

•

ACCESSORIES

- Relay module FT1256 pag. 37

•

CONFIGURATION OF THE DEVICES

- Programming bracket FT5714 and Digi2 telephone

FT2428W/A pag. 39

- Programming switching device FT1224A pag. 40

- Push-button programming with audio-video FT4660 group

and modules FT3323/3, FT3323/4 and FT3323/6 pag. 41

- Table for programming the Dip switches pag. 42

•

GENERAL INSTRUCTIONS FOR INSTALLATION

AND OPERATION

- Explanation of the meant one of audio settings

and video settings pag. 43

- Mixer-power supply FT4896 pag. 44

- Installation rules for video door entry systems pag. 45

- Table of 1216 settings according to the type

of connection cable used pag. 45

- Maximum distances and characteristics of the conductors pag. 46

- Maximum distances which can be reached by

the conductors off additional monitor power supply

and external unit pag. 48

•

OPERATING NOTES pag. 48

•

WIRING DIAGRAMS pag. 49

•

VARIATIONS OF SYSTEM DIAGRAMS pag. 49

Video door entry system with DIGI-2 cabling

TM

2

160 - 165 cm

1 2

3 4

5 6

EXTERNAL UNITS

Instructions for installing external audio-video unit standard

TM

3

TM

+

-

+

-

MIC

5

4

2

3

1

2

3

360˚

Carla

Rossi

open

close

7

9

11

8

10

12

Alternative position of the microphone

TM

4

10

2

1

10

15

1 2

3 4

Rossi

Aldo

Rossi

Use a transparent adhesive strip for a label maker (of the Dymo type) as shown in the figure.

Instructions for assembling an informative module FT3326, FT3344 and FT3346

Name tags can be best produced as follows:

TM

5

TM

Digital call FT3340

Arrange the modules only as indicated in the following drawing.

1) KEY FUNCTIONS

INTRODUCTION

The digital call module FT3340 can be used in audio and video settings, is fitted with a

name directory to store a list of user names and with an alphanumerical keypad to call

the door entry phone users by entering the code which identifies them. The main

characteristics are as follows:

• Memory capacity: 400 names of 18 alphanumerical characters.

• Graphic display with 128x64 dots/pitch resolution.

• 2 call management modes : Standard or indirect code .

• Entering the name list ( Download ) by means of programmer FT1230 or by means of

connection with a PC fitted with software FT1249/A.

• Entering the names by means of connection with the PC can be done over an RS232

line or over an RS485 line by means of the interface card FT1319.

• Reading ( Upload ) of the name list stored in the directory module by means of

connection with a PC fitted with software FT1249/A.

• Access control with the possibility of storing up to 300 password codes to activate the

relay in the porter module, typically used as a door opener.

• Possibility of displaying the graphic interface messages in one of the 9 languages

available.

CALL – SELECT MENU

BACK: Scrolls the user list in

decreasing alphabetical order

FORWARD: Scrolls the user list

in increasing alphabetical order.

SEARCH FOR NAME - EXIT MENU

CALL -

LOCAL DOOR OPENING

CANCEL CHARACTER

or CALL

INITIAL CONDITION

3) SETTING THE LANGUAGE

3A) THE FIRST TIME THE MODULE IS TURNED ON, THE LANGUAGE HAS NOT YET

BEEN SELECTED:

On power up SELECT LANGUAGE:

*ITALIAN

ENGLISH

Scroll the list by means

of the

▲▼

keys.

To select the language

required, press .

* ITALIAN

ENGLISH

FRANCAIS

The DEFAULT item sets

the ITALIAN language.

The next time the

module is turned on,

selection of the language

is requested again.

ON DISPLAY DESCRIPTIONOPERATION

TEST DESCRIPTION

4) SELF – DIAGNOSIS

On power up, the apparatus carries out a diagnostic test of the connections to check correct

communication with porter module FT1602/FT4660 and with the keypad module which

makes up FT3340. If the wordi OK appears next to the item, then it has passed the test,

otherwise, if the word FAILED appears it has failed the test.

On completion of the Self-Diagnosis mode, press the

▼

key to put the module in the into its

normal mode of operation.

The table summarising the meaning of the single tests is given below:

INITIALIZING

SPEAK. SERIAL

MODE

Check the EEPROM which contains the

user name list. If the test fails, the module is faulty.

If the test fails, check correct serial connection

with porter module FT1602 / FT4660 .

Check presence of the alphanumerical keypad which

makes up FT3340. If the wording FT3342 appears next to

the description, correct connection between the alphanu-

merical keypad and the directory module must be checked.

2) ACCESSING THE CONFIGURATION STAGE

Powered up with PR

terminal connected

to terminal - .

Or:

During normal

operation press ,

insert the supercode

and confirm

pressing .

The module is in

programming mode:

to select the menu

▲▼

to scroll the menus.

to return to the

previous menu.

NAME DIRECTORY

ACCESS CONTROL

SETTINGS

ON DISPLAY DESCRIPTIONOPERATION

3B) CHANGING THE LANGUAGE SET PREVIOUSLY:

Access to the configuration

stage has been carried out

(see point 2).

NAME DIRECTORY

ACCESS CONTROL

SETTINGS

SELECT LANGUAGE:

*ITALIAN

ENGLISH

SELECT LANGUAGE:

ITALIAN

*ENGLISH

The default language

on power up is Italian.

The language set

is marked by an asterisk

on the left-hand side.

When repowered

the lanuage resets

to Italian by default.

Select the

SETTINGS /

SELECT LANG. menu.

Scroll the list by means

of the

▲▼

keys.

To select the language

required, press

.

ON DISPLAY DESCRIPTIONOPERATION

TM

6

7) MANAGING THE DIRECTORY

7A) ENTERING A NAME

It is possible to store a name in the directory by means of infrared programmer FT1230,

or by means of software FT1249/A, or directly by means of the alphanumerical keypad

the module is fitted with.

INITIAL CONDITION

7B) ENTERING BY MEANS OF FT1230

(not available if the call mode is In direct Code - see point 8)

Press the NAME->

of FT1230.

Enter the user name

to be inserted.

EXAMPLE:

SMITH JOHN

Press the ENTER key

of FT1230.

During normal operation.

If some users have been

stored in the directory.

ENTERING

A NAME

SMITH JOHN

CODE: _ _ _

To use the lower-case

characters of the keys, press

SHIFT. To cancel the

character on the left press < .

To enter special characters,

press the combination of

keys described below:

NAME -> + A = Å

NAME -> + B = Ä

NAME -> + C = ß

NAME -> + O = Ö

NAME -> + P = Ø

NAME -> + Q = Ü

Press ESC to cancel

the user name

entry operation.

ON DISPLAY DESCRIPTIONOPERATION

ENTER TENANT

CODE

Followed by:

SCROLL NAMES

SEARCH NAME

Enter the user name.

EXAMPLE: 1

Press the ENTER key

of FT1230 to store the

user name and code.

It is possible to proceed

to enter other users.

CODICE: _ _ 1

STORING

IN PROGRESS…

INITIAL CONDITION

5) USING THE NAME DIRECTORY

5A) SCROLLING AND CALLING THE USER SELECTED

Scroll the list by means

of the

▲▼

keys.

To exit, press the key.

Press the key

to call the selected user.

It is possible to cancel

the call or the

conversation in progress

by pressing the X key.

During normal operation.

If some users have been

stored in the directory.

GIOVANNI ROSSI The names are entered

in alphabetical order.

The call has been made

correctly.

The call has not been

made correctly.

The system is engaged.

ON DISPLAY DESCRIPTIONOPERATION

ENTER TENANT

CODE

Followed by:

SCROLL NAMES

SEARCH NAME

CALL EFFECTED

Or:

USER NOT

AVAILABLE

Or:

USER BUSY

CALL EFFECTED

Or:

COMMUNICATING

INITIAL CONDITION

5B) SEARCHING FOR A NAME IN THE DIRECTORY

Press the key.

Enter the user name with part

of the extension as well.

EXAMPLE: SMITH

Press the key

to start the search.

Now it is possible

to scroll the user

name list using

the

▲▼

keys.

During normal operation.

ENTER THE

REQUIRED

NAME TO SEARCH

SMI_

SEARCH

IN PROGRESS…

SMITH JOHN

Or:

NAME NOT STORED

IN DIRECTORY

The user name found

is displayed.

The user name does

not exist.

ON DISPLAY DESCRIPTIONOPERATION

SCROLL NAMES

SEARCH NAME

Followed by:

ENTER TENANT

CODE

INITIAL CONDITION

6) USING THE CALL MODULE

EXAMPLE: If you want to

call the user with code 1.

Press key 1 on the

alphanumerical keypad.

Press the

or key to call

It is now possible to

cancel the call or the

conversation in progress

by pressing the X key.

During normal operation.

CALL USER:

_ _ 1

CALL EFFECTED

Or:

USER

NOT AVAILABLE

Or:

USER BUSY

CALL EFFECTED

Or:

COMMUNICATING

The call has been made

correctly.

The call has not been

made correctly.

The system is engaged.

ON DISPLAY DESCRIPTIONOPERATION

SCROLL NAMES

SEARCH NAME

Followed by:

ENTER TENANT

CODE

TM

7

TM

INITIAL CONDITION

7C) ENTERING BY MEANS OF SOFTWARE FT1249/A

Run the software

FT1249/A. Consult the

online Guide of the products

for the settings required.

Press the F7 key to start

downloading.

CAUTION:

The call mode selected

must correspond

with the one set in module

FT3340 (see point 9).

On completion of

downloading.

During normal operation.

Connect the cable

combined with FT1249/A

to the TX / RX / - terminals.

Module FT3340 and

FT3342 must not be under

programming.

Or:

DOWNLOAD

FAILED

DOWNLOAD

TERMINATED

If downloading is taking

place correctly.

If there are connection

problems.

The directory must

be empty.

ON DISPLAY DESCRIPTIONOPERATION

ENTER TENANT

CODE

7D) MULTIDOWNLOAD

It is possible to create an RS485 system with digital call modules FT3340/FT3342 to

upload or download an user name list on any of the modules on this system, using a

pc upgraded with software FT1249/A version 2.2 or later.

Each module must have different ID CODE (see point 9C).

7E) ENTERING DIRECTLY FROM THE KEYPAD

(not available if the call mode is Indirect Code - see point 8)

7F) CHANGING A NAME OR A USER CODE

(not available if the call mode is Indirect Code - see point 8)

Select the NAME

DIRECTORY/ CHANGE

NAMES menu.

Enter the user name to be

modified, with part of the

extension as well.

EXAMPLE: SMIT

Press the key to

proceed with searching

for the user name.

ENTER PART

OF THE NAME

REQUIRED

SMIT_

SEARCH

IN PROGRESS…

The user name to be

modified is requested.

ON DISPLAY DESCRIPTIONOPERATION

7G) CANCELLING A NAME

(not available if the call mode is Indirect Code - see point 8)

Select the NAME

DIRECTORY/DELETING

NAMES menu.

Enter the user name to be

cancelled, with part of the

extension as well.

EXAMPLE: SMI

Press the key to

proceed with searching

for the user name.

Use the

▲▼

keys to scroll

the user list. Select the user

name to be cancelled.

EXAMPLE:

SMITH JOHN

Press the key to

proceed with cancelling

the user name.

It is possible to proceed to

cancel another user.

ON DISPLAY DESCRIPTIONOPERATION

ENTER PART

OF THE NAME

REQUIRED

SMI _

SEARCH

IN PROGRESS …

SMITH JOHN

ELIMINATION

IN PROGRESS…

The user name to be

cancelled is requested.

Access to the configuration

stage has been carried out

(see point 2).

NAME DIRECTORY

ACCESS CONTROL

SETTINGS

Access to the configuration

stage has been carried out

(see point 2).

ON DISPLAY DESCRIPTIONOPERATION

NAME DIRECTORY

ACCESS CONTROL

SETTINGS

Access to the configuration

stage has been carried out

(see point 2).

Select the NAME

DIRECTORY/ENTERING

NAMES/MANUALLY

menu.

Proceed with user

name entry.

EXAMPLE:

JOHN SMITH

Press the key to

proceed with the user

code entry.

EXAMPLE: 1

The module is ready for

entering the names.

To cancel the character to

the left of the cursor, press

the X key, for special

characters, key 9.

ON DISPLAY DESCRIPTIONOPERATION

NAME DIRECTORY

ACCESS CONTROL

SETTING

_

JOHN SMITH_

CODE: _ _ 1

Press the key to store

the user name and code.

It is possible to proceed to

enter other users.

STORING

IN PROGRESS…

Or:

NAME ALREADY

IN MEMORY

_

If the user name is already

in the directory.

Use the

▲▼

keys

to scroll the user name list.

Select the user name

to be modified.

EXAMPLE: JOHN SMITH

Press the key to

proceed with modification

of the user name.

Modify the name

by means of the

alphanumerical keypad.

Press the key to

proceed with modification

of the user code.

Modify the code

by means of the

alphanumerical keypad.

Press the key to store

the user name and code.

It is possible to proceed to

modify another user.

JOHN SMITH

JOHN SMITH _

CODE: _ _ 1

CODE _ _ 2

STORING

IN PROGRESS…

Or:

NAME ALREADY

IN MEMORY

TM

8

8) SETTING THE OPERATING MODE

(Standard or indirect code)

8A) STANDARD CALL MODE ( Default )

In this operating mode the entry phone user is identified by a un User Name field and by

a Code field.

EXAMPLE: User name = Smith ; Code = 1

The call can be made in the following ways:

1) I select the user Smith by means of the

▲▼

keys ➔ I press the key ➔ I send the

call to the user identified with code 1.

2) From the keypad I enter the code 1 ➔ I press the key.

8B) INDIRECT CODE CALL MODE

In this operating mode the entry phone user is identified by the Indirect code, User

name (optional) and Code fields.

EXAMPLE: User name = Smith ; Code = 1 ; Indirect Code = 100

The call can be made in the following ways:

1) I select the user Smith by means of the

▲▼

keys ➔ I press the key ➔ I send the

call to the user identified with code 1.

2) From the keypad I enter the Indirect Code 100 ➔ I press the key ➔ I send the

call to the user identified with code 1.

Entry of the list with the listed fields can only be carried out by means of the software

FT1249/A.

The indirect code can have a maximum of 6 figures.

The User Name field can also be omitted (see Indirect Code Mode without name field

in the online Guide FT1249/A).

To update a module where a list has already been stored, it is first necessary to

completely cancel the one present, following the procedure in the 7L paragraph.

INITIAL CONDITION

7H) CANCELLING A NAME BY MEANS OF FT1230

(not available if the call mode is Indirect Code - see point 8)

Select the user name

to be eliminated by

scrolling the list

by means of the ▲▼ keys.

Press the NAME-> key

of FT1230.

Press the ENTER key

of FT1230 to confirm

elimination.

In normal mode

of operation.

If some users have been

stored in the directory.

SMITH JOHN

ELIMINATE

THE NAME?

DELETING

MEMORY...

ON DISPLAY DESCRIPTIONOPERATION

ENTER TENANT

CODE

Followed by:

SCROLL NAMES

SEARCH NAME

7I) CANCELLING ALL THE NAMES IN THE DIRECTORY

Access to the configuration

stage has been carried out

(see point 2).

NAME DIRECTORY

ACCESS CONTROL

SETTINGS

Select the NAME

DIRECTORY/DELETE

ALL NAMES menu.

Press the key

to eliminate all the

users in the directory.

Press the key

to cancel the operation.

DELETE

ALL NAMES?

ELIMINATION

IN PROGRESS…

ON DISPLAY DESCRIPTIONOPERATION

7L) DISPLAYING THE NUMBER OF NAMES ENTERED IN THE DIRECTORY,

THE SOFTWARE VERSION INSTALLED AND THE ID CODE

Select the INFO menu.

Access to the configuration

stage has been carried out

(see point 2).

Comelit

REV. 1.6

NAMES STORED: 0

ADDRESSE RS485: 255

NAME DIRECTORY

ACCESS CONTROL

SETTINGS

ON DISPLAY DESCRIPTIONOPERATION

To select the Standard call mode or indirect code, the following operations must be

carried out:

Select the SETTINGS /

CALL OPERATING

menu

Select the desired

mode by means

of the

▲▼

keys.

Press the key to

confirm the selection

Access to the configuration

stage has been carried out

(see point 2).

CALL OPERATING

* STANDARD

INDIRECT CODE

CALL OPERATING

* STANDARD

INDIRECT CODE

CALL OPERATING

STANDARD

* INDIRECT CODE

NAME DIRECTORY

ACCESS CONTROL

SETTINGS

ON DISPLAY DESCRIPTIONOPERATION

9) MODIFYING THE SYSTEM PARAMETERS

9A) SETTING THE PORTER FT1602-FT4660 PARAMETERS

(door opening time, conversation time and reset wait time)

The time which passes between closing down a communication and the possibility of

being able to start another is meant by reset wait time).

Press to select the

SETTINGS / SYSTEM

PARAMETERS / SPEAKER

PARAMETERS menu

Select the parameter to

be modified.

EXAMPLE:

conversation time.

Modify the parameter value

by means of the

▲▼

keys,

press the key to

cancel the operation.

Press the key to

confirm the value.

Access to the configuration

stage has been carried out

(see point 2).

Module FT1602 / FT4660

powered up with PR terminal

connected to terminal -.

The module is in the

programming mode

ENTER AUDIO TIMING

ENT. DOOR LOCK TIME

ENTER RESET TIME

ENTER AUDIO TIMING

ENT. DOOR LOCK TIME

ENTER RESET TIME

VALUE IN SECS. 010

PARAMETER

CHANGED

Admissible values.

Conversation time from 10 to

180 sec. Door opening time:

from 1 to 99 sec. Reset wait

time: from 0 to 10 sec.

A confirmation tone will

be heard on porter module

FT1602 / FT4660.

NAME DIRECTORY

ACCESS CONTROL

SETTINGS

ON DISPLAY DESCRIPTIONOPERATION

TM

9

TM

10) MANAGEMENT OF THE ACCESS CONTROL FUNCTION

10A) DEFAULT SUPERCODE

The supercode allows access to the configuration stage

9B) DISPLAYING THE PORTER FT1602 – FT4660 PARAMETERS

(door opening time, conversation time and reset wait time).

Select the SETTINGS /

SYSTEM PARAMETERS /

SPEAKER PARAMETERS/

VIEWING menu.

Access to the configuration

stage has been carried out.

(see point 2).

Module FT1602 / FT4660

powered up with PR terminal

connected to terminal - .

DOOR LOCK TIME 01

AUDIO TIMING 010

WAITING TIME 10

NAME DIRECTORY

ACCESS CONTROL

SETTINGS

The parameters set on the

porter FT1602 / FT4660

module are displayed.

CAUTION:

The function is

only guaranteed

with porter modules

which have a software

version of 2.0 or later.

ON DISPLAY DESCRIPTIONOPERATION

9C) SETTING THE ID CODE ( Default = 0 )

The ID code is only used in special applications.

Select the SETTINGS /

SYSTEM PARAMETERS /

RS485 ADDRESS menu.

Press the key to

confirm the selection.

Use the ▲▼ keys

to modify the value

of the ID code.

Press the key to store

the value.

Access to the configuration

stage has been carried out

(see point 2).

RS485 ADDRESS: 01

RS485 ADDRESS: 254

PARAMETER

CHANGED

The ID code displayed is

not the one configured.

The ID code displayed

is not the one configured.

The code can have a value

from 1 to 255.

NAME DIRECTORY

ACCESS CONTROL

SETTINGS

ON DISPLAY DESCRIPTIONOPERATION

10B) CHANGING THE SUPERCODE ( Default = 778899 )

Select the ACCESS

CONTROL /

SUPERCODE /

ENTER NEW ONE menu.

Enter the

new supercode.

It must have 6 figures.

Press the key to

confirm the entry.

Access to the configuration

stage has been carried out

(see point 2).

NAME DIRECTORY

ACCESS CONTROL

SETTINGS

NEW SUPERCODE:

_ _ _ _ _ _

NEW SUPERCODE:

* * * * * *

SUPERCODE

CHANGED

Or:

SUPERCODE

WRONG

ON DISPLAY DESCRIPTIONOPERATION

10C) RESETTING THE SUPERCODE

Select the ACCESS

CONTROL / SUPERCODE /

DELETE menu.

Access to the configuration

stage has been carried out

(see point 2).

SUPERCODE

CHANGED

NAME DIRECTORY

ACCESS CONTROL

SETTINGS

ON DISPLAY DESCRIPTIONOPERATION

10D) ENTERING A PASSWORD CODE (Default = no code stored)

Access to the configuration

stage has been carried out

(see point 2).

Select the ACCESS

CONTROL /

PASSWORD menu.

NAME DIRECTORY

ACCESS CONTROL

SETTINGS

ON DISPLAY DESCRIPTIONOPERATION

Select the

ENTRY menu.

Enter the desired

password value.

Press the key to

confirm the entry.

It is possible to proceed

to enter other passwords.

ENTER

DELETE

SEARCH

ENTER PASSWORD:

_ _ _ _ _ _

ENTER PASSWORD:

* * * * * *

STORING

IN PROGRESS…

ENTER PASSWORD:

_ _ _ _ _ _

You access the

door-opening password

management menu.

The password can have

from 1 to 6 characters.

10E) CANCELLING A PASSWORD CODE

Access to the configuration

stage has been carried out

(see point 2).

Select the ACCESS

CONTROL / PASSWORD

menu.

Select the DELETE menu.

Press the key

to confirm the selection.

NAME DIRECTORY

ACCESS CONTROL

SETTINGS

ENTER

DELETE

SEARCH

ENTER

DELETE

SEARCH

DELETE PASSWORD:

_ _ _ _ _ _

You access the

door-opening password

management menu.

Enter the password value

to be eliminated.

Press the key

to confirm the entry.

DELETE PASSWORD:

* * * * * *

DELETING

MEMORY...

Or:

DELETE PASSWORD:

X X X X X X

If the password was found

in the list.

If the password is not found,

the one with a similar

valuesis shown.

It is possible to scroll the list

of entered passwords

by using the

▲▼

keys.

To cancel the one selected,

press the key .

ON DISPLAY DESCRIPTIONOPERATION

It is possible to

proceed to eliminate

other passwords.

DELETE PASSWORD:

_ _ _ _ _ _

TM

10

10F) CANCELLING ALL THE PASSWORD CODES

Select the

ACCESS CONTROL /

PASSWORD menu.

Select the DELETE menu.

Press the key to

confirm elimination

of all the passwords.

Access to the configuration

stage has been carried out

(see point 2).

ENTER

DELETE

SEARCH

DELETE ALL

PASSWORDS?

DELETING

MEMORY...

NAME DIRECTORY

ACCESS CONTROL

SETTINGS

You access the

door-opening password

management menu.

ON DISPLAY DESCRIPTIONOPERATION

10G) SEARCHING FOR A PASSWORD CODE

Select

the ACCESS CONTROL /

PASSWORD menu.

Select the

SEARCH menu.

Enter the password value to

be searched for.

EXAMPLE:112233

Press the key to

confirm the entry.

It is possible to display

the list of passwords

entered using

the

▲▼

keys.

Access to the configuration

stage has been carried out

(see point 2).

ON DISPLAY DESCRIPTIONOPERATION

NAME DIRECTORY

ACCESS CONTROL

SETTINGS

You access the

door-opening password

management menu.

The password searched

for or the one with a similar

value stored in the list

is shown.

The passwords are stored

in increasing order

ENTER

DELETE

SEARCH

SEARCH PASSWORD:

_ _ _ _ _ _

SEARCH PASSWORD:

* * * * * *

SEARCH PASSWORD:

112233

SEARCH PASSWORD:

112244

INITIAL CONDITION

10H)

ACTIVATING THE DOOR OPENING RELAY BY ENTERING THE PASSWORD CODE

Press the key.

Enter the password code

Press the key.

In normal mode

of operation.

If some users have been

stored in the directory.

ENTER PASSWORD

:

_ _ _ _ _ _

ENTER PASSWORD

:

* * * * * *

PASSWORD

CONFIRMED

Or:

WRONG

PASSWORD

Entry of the password code

is requested.

If it is a code in

the memory, the relay

in module FT1602 / FT4660

is activated.

If a code is not in

the memory.

ON DISPLAY DESCRIPTIONOPERATION

ENTER TENANT

CODE

Followed by:

SCROLL NAMES

SEARCH NAME

10I) DISPLAYING THE NUMBER OF PASSWORDS ENTERED

Access to the configuration

stage has been carried out

(see point 2).

NAME DIRECTORY

ACCESS CONTROL

SETTINGS

Select the ACCESS

CONTROL / INFO menu.

ON DISPLAY DESCRIPTIONOPERATION

Comelit

PASSWORDS

ENTERED: 1

The number of passwords

entered is displayed.

11) SETTING THE TYPE OF CONNECTION WITH THE PC,

RS232 or RS485 (Default = RS232)

Access to the configuration

stage has been carried out

(see point 2).

NAME DIRECTORY

ACCESS CONTROL

SETTINGS

Select the SETTINGS /

TYPE OF DOWNLOAD

menu

Select the download mode

using the ▲▼ keys.

EXAMPLE: RS485

Press the key to

confirm the selection.

TYPE OF DOWNLOAD

*RS232

RS485

TYPE OF DOWNLOAD

*RS232

RS485

TYPE OF DOWNLOAD

RS232

* RS485

The DEFAULT setting

is RS232.

The mode set is marked by

an asterisk on the left side.

An asterisk will appear on

the left side of the item

selected.

ON DISPLAY DESCRIPTIONOPERATION

TM

11

TM

Electronic name directory module FT3342

INTRODUCTION

The electronic name directory module FT3342 can be used in audio and video

settings, is fitted with a name directory to store a list of user names.

The main characteristics are as follows:

• Memory capacity: 400 names of 18 alphanumerical characters.

• Graphic display with 128x64 dots/pitch resolution.

• 2 call management modes : Standard or indirect code .

• Entering the name list ( Download ) by means of programmer FT1230 or by means

of connection with a PC fitted with software FT1249/A.

• Entering the names by means of connection with the PC can be done over an

RS232 line or over an RS485 line by means of the interface card FT1319.

• Reading ( Upload ) of the name list stored in the directory module by means of

connection with a PC fitted with software FT1249/A.

• Possibility of displaying the graphic interface messages in one of the 9 languages

available

.

1) KEY FUNCTIONS

CALL – SELECT MENU

BACK: Scrolls the user list in

decreasing alphabetical order

FORWARD: Scrolls the user list

in increasing alphabetical order.

SEARCH FOR NAME - EXIT MENU

INITIAL CONDITION

3) SETTING THE LANGUAGE

3A) THE FIRST TIME THE MODULE IS TURNED ON, THE LANGUAGE HAS NOT YET

BEEN SELECTED:

On power up SELECT LANGUAGE:

* ITALIAN

ENGLISH

Scroll the list by means

of the

▲▼

keys.

To select the language

required, press

* ITALIAN

ENGLISH

FRANÇAIS

The DEFAULT item

ets the ITALIAN language.

The next time the module is

turned on, selection

of the language

is requested again.

ON DISPLAY DESCRIPTIONOPERATION

TEST DESCRIPTION

4) SELF – DIAGNOSIS

On power up, the apparatus carries out a diagnostic test of the connections to check cor-

rect communication with porter module FT1602/FT4660.

If the word OK appears next to the item, then it has passed the test, otherwise, if the

word FAILED appears it has failed the test. On completion of the Self-Diagnosis mode,

press the

▼

key to put the module in the into its normal mode of operation.

The table summarising the meaning of the single tests is given below:

INIZIALIZING

SPEAK. SERIAL

MODE

Check the EEPROM which contains the user name list.

If the test fails, the module is faulty.

If the test fails, check correct serial connection

with porter module FT1602 / FT4660 .

Check presence of the alphanumerical keypad

which makes up FT3340. Since it is not provided for

FT3342, the wording FT3342 must appear.

INITIAL CONDITION

5) USING THE NAME DIRECTORY

5A) SCROLLING AND CALLING THE USER SELECTED

During normal operation. SCROLL NAMES

SEARCH NAME

Scroll the list by means

of the

▲▼

keys.

To exit, press

the key

Press the key

to call the selected user.

ROSSI GIOVANNI The names are entered

in alphabetical order.

The call has been made

correctly.

The call has not been

made correctly.

The system is engaged.

ON DISPLAY DESCRIPTIONOPERATION

CALL EFFECTED

Or:

USER NOT

AVAILABLE

Or:

USER BUSY

INITIAL CONDITION

5B) SEARCHING FOR A NAME IN THE DIRECTORY

Press the key.

During normal operation.

SEARCH THE NAME

BY ENTERING

INITIAL

And then:

SELECT INITIAL:

A B C D E F G …

ON DISPLAY DESCRIPTIONOPERATION

SCROLL NAMES

SEARCH NAME

2) ACCESSING THE CONFIGURATION STAGE

Powered up with PR

terminal connected

to terminal -

The module is in

programming mode:

to select the menu

▲▼

to scroll the menus

to return to the

previous menu

NAME DIRECTORY

ACCESS CONTROL

SETTINGS

ON DISPLAY DESCRIPTIONOPERATION

3B) CHANGING THE LANGUAGE SET PREVIOUSLY:

Access to the configuration

stage has been carried out

(see point 2)

NAME DIRECTORY

ACCESS CONTROL

SETTINGS

SELECT LANGUAGE:

* ITALIANO

ENGLISH

SELECT LANGUAGE:

ITALIANO

*ENGLISH

The default language

on power up is Italian.

The language

set is marked by

an asterisk on the left-hand

side. When repowered

the language resets

to Italian by default.

Select the SETTINGS /

SELECT LANGUAGE

menu

Scroll the list by means

of the

▲▼

keys.

To select the language

required, press

ON DISPLAY DESCRIPTIONOPERATION

TM

12

6) MANAGING THE DIRECTORY

6A) ENTERING A NAME

It is possible to store a name in the directory by means of infrared programmer FT1230,

or by means of software FT1249/A.

INITIAL CONDITION

6B) ENTERING BY MEANS OF FT1230

During normal operation SCROLL NAMES

SEARCH NAME

Press the NAME->

of FT1230.

Enter the user name

to be inserted.

EXAMPLE:

ROSSI GIOVANNI

Press the ENTER key

of FT1230.

Enter the user code.

EXAMPLE: 1

ENTER

A NAME

ROSSI GIOVANNI_

ENTER NAME

ENTER

CONFIRM

ESC

_ _ 1

ENTER CODE

ENTER

CONFIRM

ESC

To use the lower-case

characters of the keys,

press SHIFT.

To cancel the character on

the left press < .

To enter special

characters,

press the combination

of keys described below:

NAME -> + A = Å

NAME -> + B = Ä

NAME -> + C = ß

NAME -> + O = Ö

NAME -> + P = Ø

NAME -> + Q = Ü

Press ESC to cancel

the user name

entry operation.

ON DISPLAY DESCRIPTIONOPERATION

Press the ENTER key

of FT1230 to store the

user name and code.

It is possible to proceed

to enter other users.

STORING

IN MEMORY...

6D) MULTIDOWNLOAD

It is possible to create an RS485 system with digital call modules FT3342 to upload or

download an user name list on any of the modules on this system, using a pc upgra-

ded with software FT1249/A version 2.2 or later.

Each module must have different ID CODE (see point 7C).

Select the initial

using the

▲▼

keys.

To exit press the key.

EXAMPLE: A

Press the key

to start the search.

It is now possible

to scroll the user name

list using the

▲▼

keys.

SELECT INITIAL:

A B C D E F G …..

SEARCHING

IN MEMORY…

ALBINI GIOVANNI

Or:

NO NAMES FOUND

WITH THIS INITIAL

The first user name in

alphabetical order with the

selected initial is displayed.

No user name with the

selected initial exists.

ON DISPLAY DESCRIPTIONOPERATION

INITIAL CONDITION

6C) ENTERING BY MEANS OF SOFTWARE FT1249/A

Run the software

FT1249/A. Consult the

online Guide of the

products for the settings

required. Press the F7 key

to start downloading.

On completion

of downloading.

During normal operation.

Connect the cable

combined with FT1249/A

to the TX / RX / - terminals.

Module FT3340 and

FT3342 must not be

under programming.

Or:

DOWNLOAD

FAILED

DOWNLOAD

TERMINATED

If downloading is taking

place correctly.

If there are connection

problems.

ON DISPLAY DESCRIPTIONOPERATION

SCROLL NAMES

SEARCH NAME

INITIAL CONDITION

6E) CANCELLING A NAME BY MEANS OF FT1230

Select the user name

to be eliminated by

scrolling the list by

means of the

▲▼

keys.

Press the NAME <- key

of FT1230.

Press the ENTER key

of FT1230 to confirm

elimination.

In normal mode

of operation

ROSSI GIOVANNI

DELETE NAME?

ENTER

CONFIRM

ESC

DELETING

MEMORY...

ON DISPLAY DESCRIPTIONOPERATION

SCROLL NAMES

SEARCH NAME

6F) CANCELLING ALL THE NAMES IN THE DIRECTORY

Access to the configuration

stage has been carried out

(see point 2).

Select the NAME

DIRECTORY/DELETE

ALL NAMES menu.

Press the key

to eliminate all the

users in the directory.

Press the key

to cancel the operation.

NAME DIRECTORY

ACCESS CONTROL

SETTINGS

DELETE

ALL NAMES?

DELETING

MEMORY...

ON DISPLAY DESCRIPTIONOPERATION

TM

13

TM

6G)DISPLAYING THE NUMBER OF NAMES ENTERED IN THE DIRECTORY, THE

SOFTWARE VERSION INSTALLED AND THE ID CODE

Select the INFO menu.

Access to the configuration

stage has been carried out

(see point 2).

Comelit

REV. 2.4

NAMES STORED: 00

ADDRESS RS485 255

NAME DIRECTORY

ACCESS CONTROL

SETTINGS

ON DISPLAY DESCRIPTIONOPERATION

7 MODIFYING THE SYSTEM PARAMETERS

7A) SETTING THE PORTER FT1602-FT4660 PARAMETERS

(door opening time, conversation time and reset wait time.

The time which passes between closing down a communication and the possibility of

being able to start another is meant by reset wait time).

Press to select the

SETTINGS / SYSTEM

PARAMETERS / SPEAKER

PARAMETER menu

Select the parameter to

be modified. EXAMPLE:

AUDIO TIMING.

Modify the parameter value

by means of the ▲▼ keys,

press the key to

cancel the operation

.

Press the key to

confirm the value

Access to the configuration

stage has been carried out

(see point 2).

Module FT1602 / FT4660

powered up with PR terminal

connected to terminal -.

The module is in the

programming mode

ENTER AUDIO TIMING

ENT. DOOR LOCK TIME

ENTER RESET TIME

ENTER AUDIO TIMING

ENT. DOOR LOCK TIME

ENTER RESET TIME

VALUE IN SECS. 010

PARAMETER

CHANGED

Admissible values.

Conversation time from 10 to

180 sec. Door opening time:

from 1 to 99 sec. Reset wait

time: from 0 to 10 sec.

A confirmation tone will

be heard on porter module

FT1602/FT4660.

NAME DIRECTORY

ACCESS CONTROL

SETTINGS

ON DISPLAY DESCRIPTIONOPERATION

7B) DISPLAYING THE PORTER FT1602 – FT4660 PARAMETERS

(door opening time, conversation time and reset wait time).

Select the SETTINGS /

SYSTEM PARAMETERS /

SPEAKER PARAMETER/

VIEWING menu.

Access to the configuration

stage has been carried out.

(see point 2).

Module FT1602 / FT4660

powered up with PR terminal

connected to terminal - .

DOOR LOCK TIME 01

AUDIO TIMING 010

WAITING TIME 10

NAME DIRECTORY

ACCESS CONTROL

SETTINGS

The parameters set on the

porter FT1602/FT4660

module are displayed.

CAUTION: The function is

only guaranteed

with porter modules

which have a software

version of 2.0 or later.

ON DISPLAY DESCRIPTIONOPERATION

7C) SETTING THE ID CODE ( Default = 0 )

The ID code is only used in special applications.

Access to the configuration

stage has been carried out

(see point 2).

Select the

SETTINGS / SYSTEM

PARAMETERS /

ADDRESS RS485 menu

The ID code displayed is

not the one configured.

NAME DIRECTORY

ACCESS CONTROL

SETTINGS

ADDRESS RS485 : 01

ON DISPLAY DESCRIPTIONOPERATION

Press the key to

confirm the selection.

Use the ▲▼ keys

to modify the value

of the ID code

Press the key to store

the value.

ADDRESS RS485 : 01

ADDRESS RS485 : 254

PARAMETER

CHANGED

The ID code displayed

is not the one configured.

The code can have a value

from 1 to 255.

Access to the configuration

stage has been carried out

(see point 2).

Select the SETTINGS /

TYPE OF DOWNLOAD

menu

Select the download mode

using the ▲▼ keys.

EXAMPLE: RS485

Press the key to

confirm the selection.

The DEFAULT setting

is RS232.

The mode set is marked by

an asterisk on the left side.

An asterisk will appear on

the left side of the item

selected.

ON DISPLAY DESCRIPTIONOPERATION

NAME DIRECTORY

ACCESS CONTROL

SETTINGS

TYPE OF DOWNLOAD

*RS232

RS485

TYPE OF DOWNLOAD

*RS232

RS485

TYPE OF DOWNLOAD

RS232

* RS485

8) SETTING THE TYPE OF CONNECTION WITH THE PC,

RS232 or RS485 (Default = RS232)

TM

14

UP

U

P

UP

3

1

3

2

4

UP

1

3

UP

1

2

UP

3

ALTO

1 2 3

4 5

6 7

Instructions for installing external audio-video unit vandal resistant

TM

15

TM

UP

yellow

green

ALTO

--

ALTO

UP

MIC

+

-

+

-

UP

8 9

10 11

12 13

TM

16

U

P

UP

U

P

UP

ALTO

UP

1

2

14

15

16

SOLUTION “A”

SOLUTION “B”

TM

17

TM

Digital call module FT3070/A

INTRODUCTION

The digital call module FT3070/A can be used in audio and video settings, and allows a door

entry phone user to be called by entering their code. The main characteristics are as follows:

• Alphanumerical display with 32 characters.

• Can be combined with porter modules FT3262 (combined with module FT1602) and

FT3268 (combined with module FT4660).

• STANDARD or INDIRECT CODE operating mode.

• Possibility of modifying the Door-opening Time, Conversation Time and Module reset wait

Time parameters of the porter module.

• ACCESS CONTROL function to open the entrance by entering a pre-recorded password

code.

• PC interface for management of the INDIRECT CODE mode by means of an RS232 or

RS485 serial line.

• Possibility of displaying the graphic interface messages in one of the 9 languages

available.

1) KEY FUNCTIONS

CANCEL: exit menu

or cancel operation

CALL – DOOR-OPENING –

MENU SELECTION

2) INSTALLATION OF THE MODULE

To use the FT3070/A module with FT3262 (combined with module FT3602) and FT3268

(combined with module FT4660), see the diagram 29 on page 74.

To prevent any interference caused by electrostatic discharges, it is advisable to screen

the casing as shown under.

INITIAL CONDITION

3) HOW TO USE THE DIGITAL MODULE

3A) CALL TO A USER:

Module supplied

in stand-by condition.

ENTER

TENANT CODE

TENANT:_ _ 1

PRESS TO CALL

If the call is successful

the following will appear:

CALL

EFFECTED

If the call is unsuccessful

the following will appear:

USER NOT

AVAILABLE

Or, if the riser is engaged,

the following will appear:

TENANT BUSY

ON DISPLAY DESCRIPTIONOPERATION

Enter the code by means

of the numerical keypad

of module FT3070/A.

EXAMPLE: call to user

with code 1

Press the key

to send the call.

INITIAL CONDITION

3B) RESETTING A CALL OR A CONVERSATION

Call sent or conversation

going on.

Press the X key. Module FT3070/A returns

to the stand-by state.

CALL

EFFECTED

Or:

COMMUNICATING…

ENTER

TENANT CODE

Module supplied with

terminal PR connected to

terminal -.

Or:

During normal operation

press , insert

the supercode and confirm

pressing .

The module is in the

programming stage.

Menu scrolling takes

place automatically

every 2 seconds.

MAIN

SETTINGS

4) SETTINGS

4A) ACCESSING THE CONFIGURATION STAGE

ON DISPLAY DESCRIPTIONOPERATION

Connessione a massa FT3070/A e FT3072/A.

INITIAL CONDITION

Access to the configuration

stage has been carried out.

(see point 4A).

Porter module FT3262/

FT3268 supplied

with terminal PR

connected to terminal -.

The module is in the

programming stage.

Menu scrolling takes

place automatically every

2 seconds.

The porter module is in the

programming stage.

MAIN

SETTINGS

4B) SYSTEM PARAMETERS

4B-1) MODIFYING THE PORTER MODULE CONVERSATION, DOOR-OPENING

AND RESET WAIT TIME PARAMETERS

This operation allows the conversation, door-opening relay closing and reset wait times

of the porter module to be modified.

TM

18

Entry of the list with the fields listed can only be done by means of the software

FT1249/A set as INDIRECT CODE mode without field Name.

4B-4) CALL MODE

The parameter sets the operating mode of the call module come STANDARD or

INDIRECT CODE.

STANDARD CALL MODE (Default):

In this operating mode the entry phone user is identified by a Code.

The call takes place in the following way:

• I enter code 1 on the keypad ➔ I press the key and send the call to the user

identified by code 1

INDIRECT CODE CALL MODE:

In this operating mode the entry phone user is identified by the Indirect code and Code

fields.

EXAMPLE: User Rossi Giovanni identified by Code = 1 and Indirect code = 100

The call takes place in the following way:

• I enter the Indirect code 100 on the keypad ➔ I press the key and send the call

to the user identified by code 1.

INITIAL CONDITION

Access to the configuration

stage has been carried out.

(see point 4A).

The module is in the

program-

ming stage.

Menu scrolling takes

place automatically

every 2 seconds.

MAIN

SETTINGS

*

N.B: The values in

brackets indicate the

min and max limits

of the parameter

(ref. table page 21).

CALL MODE ( 0 -1 )

*

VALUE: _

Select the SETTINGS /

SYSTEM PARAM. /

CALL MODE menu by

means of the key.

To cancel an operation

or to exit the menu press

the X key.

ON DISPLAY DESCRIPTIONOPERATION

If the entry has been made

correctly.

If the parameter does not

come within the foreseen limits.

PARAMETER

CHANGED

Or:

WRONG

ENTRY

Enter the desired value

of the parameter.

Press the key

to confirm the value

of the parameter.

4B-2) DISPLAY OF THE PARAMETERS OF THE CONVERSATION, DOOR-OPENING

AND RESET WAIT TIMES OF THE PORTER MODULE

This operation allows the values of the conversation, door-opening relay closure and

reset wait time values set in the porter module to be displayed.

INITIAL CONDITION

Access to the configuration

stage has been carried out.

(see point 4A).

Porter module FT3262/

FT3268 supplied

with terminal PR

connected to terminal -.

Select the SETTINGS /

SYSTEM PARAM. /

SPEAKER PARAM. /

VIEWING menu by means

of the key.

To exit the menu press

the X key.

After the modification has

been made, remove the

connections between PR

and – on the FT3262 and

FT3268 terminals.

The module is in the pro-

gram-ming stage. Menu

scrolling takes place

automatically every

2 seconds.

The module is in the

programming stage

After 3 seconds, the values

of the other parameters are

displayed in sequence

ON DISPLAY DESCRIPTIONOPERATION

MAIN

SETTINGS

AUDIO TIMING

VALUE: 180

*

N.B: The values in

brackets indicate the min

and max limits of the

parameter (ref. table

page 21).

If the entry has been made

correctly.

If the parameter does not

come within the foreseen limits.

ON DISPLAY DESCRIPTIONOPERATION

DOWNL. TYPE( 0 -1 )

*

VALUE: _

PARAMETER

CHANGED

Or:

WRONG

ENTRY

Select the SETTINGS /

SYSTEM PARAM. /

DOWNLOAD TYPE menu

by means of the key.

To cancel an operation

or to exit the menu press

the X key.

Enter the desired value

of the parameter.

Press the key

to confirm the value

of the parameter.

4B-3) TYPE OF SERIAL DOWNLOAD

The parameter sets the type of connection used to download the list used for managing

the INDIRECT CODE mode.

An RS232 or RS485 interface is available.

INITIAL CONDITION

Access to the configuration

stage has been carried out.

(see point 4A).

The module is in the program-

ming stage. Menu scrolling

takes place automatically

every 2 seconds.

MAIN

SETTINGS

It is possible to modify

the conversation time, the

door-opening relay activation

time and the reset wait time.

Menu scrolling takes

place automatically

every 2 seconds.

*

N.B: The values in brackets

indicate the min and max

limits of the parameter

(ref. table page 21).

If the entry has been made

correctly.

If the parameter does not come

within the foreseen limits

ON DISPLAY DESCRIPTIONOPERATION

SPEAKER PAR.

ENTER t AUDIO

t AUDIO ( 10-180 )

VALUE: _ _ _

t AUDIO ( 10-180 )

*

VALUE: 100

PARAMETER

CHANGED

Or:

WRONG

ENTRY

Select the SETTINGS /

SYSTEM PARAM. / SPEAKER

PARAM.

menu by means of

the key. To cancel

an operation or to exit the

menu press the X key.

By means of the key,

select the menu item

corresponding to the

parameter to be modified.

EXAMPLE: Modifying the

conversation time.

Enter the desired value.

EXAMPLE: 100

Press the key

to confirm the value

of the parameter.

After the modification has

been made, remove the

connections between

PR and – on the FT3262

and FT3268 terminals.

4B-5) RS485 ADDRESS

The value of this parameter is only used in special applications.

INITIAL CONDITION

Access to the configuration

stage has been carried out.

(see point 4A).

The module is in the

program-ming stage.

Menu scrolling takes

place automatically

every 2 seconds.

MAIN

SETTINGS

Page is loading ...

fortessa Digital 2 Wire Door Entry User manual

This manual is also suitable for

fortessa Digital 2 Wire Door Entry User manual

Related papers

Other documents