Hikoki CC 14 User manual

Category
Power tools
Type
User manual

This manual is also suitable for

DOUBLE INSULATION
DOUBLE ISOLATION
AISLAMIENTO DOBLE
MODE D’EMPLOI ET INSTRUCTIONS DE SECURITE
AVERTISSEMENT
Une utilisation incorrecte et dangereuse de cet outil motorisé peut entraîner la
mort ou de sérieuses blessures corporelles!
Ce mode d’emploi contient d’importantes informations à propos de la sécurité de
ce produit. Prière de lire et de comprendre ce mode d’emploi avant d’utiliser l’outil
motorisé. Garder ce mode d’emploi à la disponibilité des autres utilisateurs avant
qu’ils utilisent l’outil motorisé.
INSTRUCTION MANUAL AND SAFETY INSTRUCTIONS
WARNING
Improper and unsafe use of this power tool can result in death or serious bodily
injury!
This manual contains important information about product safety. Please read
and understand this manual before operating the power tool. Please keep this
manual available for others before they use the power tool.
MANUAL DE INSTRUCCIONES E INSTRUCCIONES DE SEGURIDAD
ADVERTENCIA
¡La utilización inapropiada e insegura de esta herramienta eléctrica puede resultar
en lesiones serias o en la muerte!
Este manual contiene información importante sobre la seguridad del producto.
Lea y comprenda este manual antes de utilizar la herramienta eléctrica. Guarde
este manual para que puedan leerlo otras personas antes de que utilicen la
herramienta eléctrica.
CC 14
MODEL CUT-OFF MACHINE
MODÈLE TRONÇONNEUSE
MODELO TRONZADORA
English
3
IMPORTANT INFORMATION
Read and understand all of the operating instructions, safety precautions and warnings in
the Manual before operating or maintaining this power tool.
Most accidents that result from tool operation and maintenance are caused by the failure to
observe basic safety rules or precautions. An accident can often be avoided by recognizing
a potentially hazardous situation before it occurs, and by observing appropriate safety
procedures.
Basic safety precautions are outlined in the SAFETY section of this manual and in the
sections which contain the operation and maintenance instructions.
Hazards that must be avoided to prevent bodily injury or machine damage are identified by
WARNINGS on the tool and in this Manual.
Never use this tool in a manner that has not been specifically recommended by HITACHI,
unless you first confirm that the planned use will be safe for you and others.
MEANINGS OF SIGNAL WORDS
WARNING: Indicates a potentially hazardous situations which, if ignored, could result in
serious personal injury.
CAUTION: Indicates a hazardous situations which, if ignored, could result in moderate
personal injury. or could cause machine damage.
NOTE: emphasizes essential information.
English
4
SAFETY
SAFETY RULES FOR POWER TOOLS.
READ ALL OF THE WARNINGS AND OPERATING INSTRUCTIONS IN THIS MANUAL
BEFORE OPERATING OR MAINTAINING THIS TOOL.
WARNING: When using this electric tool, take all necessary precautions to minimize
the risk of electric shock or other personal injury.
In particular, always comply with the following safety rules:
1. ALWAYS KEEP GUARDS IN PLACE and in working order.
2. ALWAYS REMOVE ADJUSTING KEYS, WRENCHES AND STOPPER BEFORE STARTING
TOOL. Always confirm that all keys, adjusting wrenches and stopper have been removed
from the tool before it is turned on.
3. ALWAYS KEEP WORK AREA CLEAN. Avoid injuries by not cluttering the work areas and
work benches.
4. NEVER USE TOOL IN HAZARDOUS ENVIRONMENTS. Never use power tools in damp or
wet places, and never expose them to rain. Always keep the work area well lighted.
5. KEEP CHILDREN AWAY. All visitors should be kept safe distance from work area.
6. MAKE WORKSHOP KID PROOF with padlocks, master switches, or by removing starter
keys.
7. NEVER FORCE THE TOOL. It will do the job better and more safely if it is operated at the
rate for which it was designed.
8. ALWAYS USE THE RIGHT TOOLS. Never force a tool or an attachment to do a job for
which it was not designed.
9. ALWAYS WEAR PROPER APPAREL WHEN WORKING WITH THE TOOL. Never wear
loose clothing, gloves, neckties, rings, bracelets or other jewelry which may get caught
in the moving parts. Always wear non-slip footwear, preferably with steel toes. Wear
protective hair covering to contain long hair.
10. ALWAYS USE EYE PROTECTION WHEN WORKING WITH THE TOOL, TO PREVENT EYE
INJURY. Ordinary eyeglasses only have impact resistant lenses, they are NOT safety
glasses. Also, use a face mask for additional safety, and wear a dust mask if the cutting
operation produces dust.
11. ALWAYS SECURE THE WORKPIECE TO THE VISE OR THE BASE.
Use clamps or a vise to hold the workpiece in place. Its safer than using your hand, and
it frees both hands to operate the tool.
12. NEVER OVERREACH. Always keep proper footing and balance when working with the
tool.
13. ALWAYS MAINTAIN TOOLS WITH CARE. Always keep tools sharp and clean for best and
safest performance. Always follow instructions for lubricating the tool and for changing
accessories.
14. ALWAYS DISCONNECT THE TOOL before servicing and before changing cut-off wheels
or other accessories.
15. NEVER RISK UNINTENTIONAL STARTING WHEN PLUGGING IN THE TOOL. Always
confirm that the switch is in the OFF position before inserting the power plug into the
receptacle.
English
5
16. ALWAYS USE RECOMMENDED ACCESSORIES ONLY, WHEN OPERATING THIS TOOL.
Consult this instruction manual for descriptions of recommended accessories. To avoid
personal injuries, use only recommended accessories in conjunction with this tool.
17. NEVER STAND ON TOOL. Prevent serious injury by not tipping the tool and by not risking
unintentional contact with the cut-off wheel.
18. ALWAYS CHECK FOR DAMAGED PARTS BEFORE USING TOOL. Always check the guard
and all other components for damage before using the tool, to assure that they will
function properly. Check all moving parts for proper alignment, freedom from binding
and other conditions that might affect proper operation. Always repair or replace any
damaged guards or other damaged components before using the tool.
19. NEVER LEAVE THE TOOL RUNNING WHILE UNATTENDED; ALWAYS TURN THE POWER
OFF WHEN THE TOOL IS NOT IN USE. Always unplug the power cord when the tool is
not in use. Dont leave tool until it comes to a complete stop.
20. This tool was not designed to be used for mass-production applications, and should not
be used in mass-production environments.
21. This tool is intended for residential use only.
22. When servicing this tool, use only authorized replacement parts.
23. Apply AC 115 volts only to this tool. Applying the wrong voltage could cause the POWER
TOOL to operate improperly and could cause serious personal injury or damage to the
tool.
Specific Safety Rules for Use of this Power Tool
WARNING: The following specific operating instructions must be observed when
using this POWER TOOL, to avoid injury:
DOs
ALWAYS OBSERVE THE FOLLOWING RULES, TO ASSURE SAFE USE OF THIS TOOL:
1. Review this Manual and familiarize yourself with the safety rules and operating instructions
for this POWER TOOL, before attempting to use it.
2. Always confirm that the POWER TOOL is clean, before using it.
3. Always wear snug-fitting clothing, non-skid footwear (preferably with steel toes) and eye
protection, when operating the POWER TOOL.
4. Always handle the POWER TOOL carefully. If the POWER TOOL is dropped or struck
against a hard object, it might become deformed or cracked or sustain other damage.
5. Always cease operating the tool at once, if you notice any abnormality whatsoever.
6. Always confirm that all components are mounted properly and securely, before using the
tool.
7. When replacing the cut-off wheel, always confirm that the rpm rating of the new wheel
is correct for use on this tool.
8. Always shut off the power and wait for the cut-off wheel to completely stop rotating,
before undertaking any maintenance or adjustments.
9. Always clamp or otherwise secure the workpiece to the vise; otherwise the workpiece
might be thrown from the base and cause bodily harm.
10. Always confirm that the cut-off wheel is free from any cracks, before using the tool.
11. Always confirm that the parts which fix the cut-off wheel are not damaged.
Damaged parts cause the breakage of the cut-off wheel.
English
6
12. Always make a trial run first, before attempting any new use of the tool.
13. Always use only the peripheral surface of the cut-off wheel.
14. Always handle the cut-off wheel with care, when dismounting and mounting it.
15. Always keep your hands out of the line of the cut-off wheel.
16. Always confirm that the safety cover are in the proper places, before using the tool.
17. Inspect the tool power cord periodically.
18. Always confirm that the proper lengths and types of extension cords are being utilized,
when if needed, before starting the tool.
19. Always confirm that the motor air vents are fully open, before using the tool.
20. Always wait until the motor has reached full speed, before starting a cut.
21. Always keep the handles dry, clean and free of oil and grease. Hold the tool firmly, when
in use.
22. Always fix the motor section using the chain when carrying about the tool.
23. Always keep the cut-off wheels in a dry place, as humidity affects the strength of the cut-
off wheels.
DONTs
NEVER VIOLATE THE FOLLOWING RULES, TO ASSURE SAFE USE THIS TOOL:
1. Never operate the POWER TOOL unless you fully understand the operating instructions
contained in this Manual.
2. Never leave the POWER TOOL, unattended, without first unplugging the power cord.
3. Never operate the POWER TOOL when you are tired, or after you have taken any
medications or have consumed any alcoholic beverages.
4. Never use the POWER TOOL for applications not specified in the Instruction Manual.
5. Never operate the tool while wearing loose clothing, a necktie or jewelry, or while your
hair is uncovered, to protect against getting caught in the moving machinery.
6. Never reach around or behind the cut-off wheel.
7. Never touch any moving parts, including the cut-off wheel, while the tool is in use.
8. Never remove any safety devices or wheel guards; use of the tool without them would
be hazardous.
9. Never lock the safety cover, (always confirm that it slides smoothly, before using the
tool).
10. Never abuse the power cord of the tool.
11. Never attempt to move a plugged-in POWER TOOL while your finger is on the starting
switch.
12. Never use the POWER TOOL if the starting switch doesnt turn on and off properly.
13. Never use the POWER TOOL if the plastic housing or the handle is cracked or deformed.
14. Never use the POWER TOOL near flammable liquids or gases, since sparking could cause
an explosion.
15. Never clean plastic components with solvents, since the plastic may dissolve.
16. Never operate the tool unless all of the wheel guards are in place.
17. Never allow the cut-off wheel to be struck against a hard object, as it might get cracked.
18. Never twist the cut-off wheel during cutting operation.
19. Never expose hands, feet and fragile things to the grinding sparks, as the grinding sparks
may harm them.
20. Never use the lateral side of the cut-off wheel.
English
7
WARNING
For Your Own Safety Read This Instruction Manual Before Operating The Cut-Off Machine.
1. Always wear eye protection, when using the tool.
2. Always keep hands out of the line of the cut-off wheel.
3. Never operate the tool without the guards in place.
4. Never perform any freehand operation with the tool.
5. Never reach around the cut-off wheel.
6. Always shut off the power and wait for the cut-off wheel to stop turning before adjusting
or maintaining the tool.
FOREWORD
The information contained in this manual is designed to assist you in the safe operation and
maintenance of the POWER TOOL. Some illustrations in this manual may show details or
attachments that differ from those on your own POWER TOOL.
DOUBLE INSULATION FOR SAFER OPERATION
To ensure safer operation of this electric power tool, HITACHI has adopted a double
insulation system. Double insulation as used here, means a system of two insulations
physically separated and arranged between electrically conductive materials connected to
the power supply and to the outer frame handled by the operator. Therefore, the nameplate
shows both the mark and Double insulation or either one on the power tool.
Although this system has no external grounding, you must still follow the normal safety
precautions given in this manual.
To keep the double insulation system effective, follow these precautions;
* To avoid lessening the double insulation-feature, always get in touch with your dealer or
an authorized HITACHI power tool repair shop when assembling, disassembling or
replacing parts other than accessories or carbon brushes.
* Clean the exterior of the tool with a soft cloth moistened in soap water, and dry thoroughly.
Dont use chloric solvent, gasoline or thinner on plastic components; otherwise they might
dissolve.
SAVE THESE INSTRUCTIONS
AND
MAKE THEM AVAILABLE TO
OTHER USERS OF THIS TOOL!
English
8
PART NAMES
Fig. 1 Fig. 2
Wheel Cover
Safety Cover
Sub Cover
Cut-off Wheel
Handle
Motor
Spark Chute
Lock-off Button
Shaft
Vise(B)
Vise(A)
Base
Switch
Stopper
Wheel Washer
Screw Handle
Chain
SPECIFICATIONS
Item Model CC 14
Type Protected type, series commutator motor
Motor
Power source Single-phase AC 60Hz
Voltage 115 Volts
Full-load current 15 Amp
Type Reinforced resinoid cut-off wheel
Outside Dia 14" (355 mm)
Cut-off Dimensions Thickness 7/64" (2.8 mm)
wheel Hole Dia. 1" (25.4 mm)
Max. working
16000 ft/min (4800 m/min)
peripheral speed
No-load speed 3700 rpm
No-load peripheral speed 13540 ft/min (4125 m/min)
Applicable workpiece materials
Round bars, pipes and various types of shaped steel
90°
Max. Height 3-59/64" (100 mm) Max. Height 2-5/32" (55 mm)
Max. cutting
Max. Width 6-1/2" (165 mm) Max. Width 8-3/8" (213 mm)
dimensions
45°
Max. Height 3-59/64" (100 mm) Max. Height 2-5/32" (55 mm)
Max. Width 3-5/8" (92 mm) Max. Width 5" (127 mm)
Max. opening of vise 8-3/8" (213 mm)
Net weight 37 lbs. (17 kg)
Cord 2 conductor type cabtire cable 8 ft (2.5 m)
English
9
STANDARD ACCESSORIES
q Cut-Off Wheel 14" × 7/64" × 1"(355 × 2.8 × 25.4 mm)
Model CC 14 (A36RBIG) 1pc. (Code No.964975Z)
(Attached to the main body)
w Spanner
Fig. 3
WARNING: The use of attachment or accessories not recommended in this manual
may be hazardous.
PREPARATION BEFORE OPERATION
Make the following preparations before operating the power tool:
1. Installation
Install the machine on a level flat place, and keep it in a stable condition.
2. Extension Cord.
To use the power tool when no suitable power
source is nearby, use an extension cord of
suitable size to ensure safety, and to prevent
power loss and overheating.
Determine from the accompanying table the
required extension cord wire size.
Check power cord and extension cords for loose
or exposed wires and damaged insulation,
before using.
Repair or replace as needed, before using the
power tool.
NOTE: The lower the wire size number, the heavier the wire, and the farther it will carry
current without a voltage drop.
WARNING: Never connect this unit to an electrical power source until all operating
instructions have been read and understood.
3. Take off the chain.
As the movable part is pulled down by a chain when shipping out, slightly push the
handle down and take off the chain from the handle.
Ampere rating
12.1 to 16.0
(on nameplate)
Ext. cord length
Wire gauge size
A.W.G (mm
2
)
25 ft 14 A.W.G
(7.5 m) (2.0 mm
2
)
50 ft. 12 A.W.G
(15 m) (3.5 mm
2
)
100 ft. Not
(30.5 m) recommended
English
10
BEFORE USING
1. Make sure the power source is appropriate for the tool.
WARNING: Never connect the power tool unless the available AC power source
is of the same voltage as that specified on the nameplate of the tool.
2. Make sure the trigger switch is turned OFF.
WARNING: If the power cord is connected to the power source with the trigger
switch turned ON, the power tool will start suddenly and could
cause a serious accident.
3. Check the cut-off wheel for visible defects.
Confirm that the cut-off wheel is free of cracks or other visible damages.
4. Confirm that the cut-off wheel is fixed securely to the power tool.
Using the supplied spanner, tighten the clamping bolt on the cut-off wheel mounting
shaft to secure the cut-off wheel.
WARNING: When the clamping bolt is loose, the cut-off wheel may be damaged
when the wheel axle starts revolving, causing a hazardous condition.
5. Check the safety covers for proper operation.
Possible accidents such as a cracked out-off wheel is prevented by this safety cover
(wheel cover).
Although it has been fully clamped at the factory prior to delivery, securely reclamp the
mounting screws for safety.
Safety cover, wheel cover and sub cover are designed to protect the operator from
coming into contact with the cut off wheel during operation of the tool.
WARNING: NEVER OPERATE THE POWER TOOL if the safety covers do not
function smoothly.
6. Use cut-off wheels whose peripheral speed ratings are over the maximum
working peripheral speed.
When replacing the cut-off wheel, ensure that the replacement cut-off wheel has a
designed peripheral speed in excess of 16000 ft/min (4800m/min).
WARNING: Never use cut-off wheels whose peripheral speed ratings are under
the maximum working peripheral speed.
7. Confirm the stopper position.
Confirm that the stopper which was used for installtion and removal of the cut-off wheel
has returned to the retract position.
8. Securely fix the cutting material.
Ensure that the material is securely fastened with the vise. If it is not, a serious accident
could be caused if the material comes loose or the cut-off wheel breaks during operation.
English
11
9. Check the Power Receptacle.
To prevent overheating, accidental stopping or intermittent operation, confirm that the
power plug fits properly in the electrical receptacle and does not fall out after it is inserted.
Repair or replace the receptacle, if it is faulty.
10.Confirm that the tools cabtire power cable is not damaged.
Repair or replace the power cord if an inspection of the cabtire cable indicates that it is
damaged.
AFTER CONNECTING THE POWER PLUG TO AN APPROPRIATE AC POWER SOURCE,
CHECK THE OPERATION OF THE TOOL, AS FOLLOWS:
11.Trial Run.
After confirming that no one is standing in front of it, step away from the front position
and start the power tool and confirm that no operating abnormalities exist before
attempting a cutting operation.
Trial run periods:
When replacing the cut-off wheel .......... Over 3 minutes.
When starting routine work.................... Over 1 minute.
12.Inspect the rotating stability of the cut-off wheel.
For precise cutting, rotate the cut-off wheel and check for deflection to confirm that the
wheel is not noticeably unstable; otherwise vibration might occur and cause an accident.
PRACTICAL APPLICATIONS
WARNING: Never remove or install a workpiece while the cut-off wheel is rotating,
to avoide personal injury.
1. Procedure for fixing the cutting material (Fig. 4 and 5).
Quick Vise
Place the workpiece material between Vise (A) and Vise (B), raise the clutch and push the
Screw Handle to bring Vise (A) lightly into contact with the workpiece material, as shown
in Fig. 4. Then, turn the clutch down, and securely fix the workpiece material in position
by turning the Screw Handle. When the cutting job is completed, turn the Screw Handle
2 or 3 times to loosen the vise, and remove the workpiece material, as shown in Fig. 5.
Fig. 4 Fig. 5
Vise (B)
Vise (A)
Clutch
Screw
Handle
Workpiece
material
Vise (B)
Vise (A)
Clutch
Screw
Handle
Workpiece
material
English
12
2. Switch operation.
The trigger switch lock-off button is designed to prevent
inadvertent operation of the power tool. To operate
the power tool, it is necessary to first fully insert the
lock-off button into the hole on the handle (see Fig.6).
The trigger switch will not operate unless the lock-off
button has been pushed in.
When the trigger switch is released, the power goes off
and the lock-off button automatically returns to its
original position, locking the trigger switch.
Fig. 6
WARNING: Always remove the lock-off button from the handle when the power
tool is not in use. This will ensure that the power tool cannot be turned
on accidentally, or by someone (especially a child) not qualified to use
the power tool. If the lock-off button is left in the handle, serious
personal injury could result. Since the lock-off button fits rather tightly,
it may be necessary to turn it to the left and right during mounting and
removing.
3. Cutting operation.
(1) Rotate the cut-off wheel, gently press down the handle, and bring the cut-off wheel
close to the material to be cut.
(2) When the cut-off wheel contacts the material, gently press down the handle further
and start cutting.
(3) When cutting (or designated slotting) is completed, raise the handle and restore it to
its original position.
(4) At the termination of each cutting process, turn OFF the switch to stop rotation and
proceed with the subsequent cutting job.
WARNING: Confirm that the trigger switch is turned OFF and that the power
plug has been removed from the receptacle, whenever the tool is not
in use.
Always remove the lock-off button from the handle, and store it in
a secure place, after completing the work.
CAUTION: Increased pressure on the handle will not increase the cutting speed.
On the contrary, too much pressure may result in overload of the
motor and/or decreased cutting efficiency.
Trigger
Lock-off
Button
Handle
Hole
English
13
4. Cutting at angles (Fig. 7 and 8).
The machine permits cutting at angles of 45° or 60°
Fig. 7
Loosen the two 25/64" (10 mm) bolts on the vise (B), then set the working surface on the
vise-jaw at any angles of 0°, 30° or 45° as shown in Fig. 7.
Upon completion of setting, securely tighten the two 25/64" (10 mm) bolts, as shown in
Fig. 8.
When setting at an
angle of 0°
When setting at an
angle of 30°
When setting at an
angle of 45°
Fig. 8 Fig. 9
When wide material is to be cut at an angle, it should be firmly clamped by fixing a steel
board like Fig. 9 to the vise (B), as shown in Fig. 9.
5. Moving the stationary vise-jaw (Fig. 10).
The vise opening is set at the maximum of 5-15/
64"(133mm) when shipped from the factory.
In case an opening more than 5-15/64"(133mm) is
required, move the vise-jaw to the position shown
by the chain line, after unscrewing the two bolts.
The maximum opening can be set in two steps 6-
13/16"(173mm) and 8-3/8"(213mm).
When the material to be cut is excessively wide, the
vise can be effectively used by repositioning the
stationary side of the vise jaws.
Fig. 10
25/64"
(10 mm)
Vise (B)
The vise jaws open
to 5-15/64" (133 mm)
while the vise can
be set in two steps
6-13/16" (173 mm)
and 8-3/8" (213 mm)
Flat hd. screw of more than
15/64" × 19/32" (6 mm × 15)
8-27/64"
(214 mm)
2-11/64" (55 mm)
1-5/64" (27.5 mm)
1-5/64" (27.5 mm)
4-23/32"
(120 mm)
1-49/64"
(45 mm)
15/64"
(6 mm) nut
Vise (B)
Two holes 1/4"
(6.5 mm)
More than 15/64"
(6 mm)
Steel
board
English
14
6. Using a Metallic Block (Fig. 11).
When the cut-off wheel has a reduced outer
diameter, insert between the vise (A) and (B) a
metallic block slightly smaller than the dimension
of workpiece being cut to use the cut-off wheel
economically.
Fig. 11
CUT-OFF WHEEL DISMOUNTING AND MOUNTING
WARNING: Always turn off the trigger switch and disconnect the power plug from
the receptacle before removing or installing a wheel, to prevent accidental
injury.
1. Dismounting the Cut-Off Wheel (Fig. 12).
(1) Press the stopper and loosen the bolt with a
spanner.
NOTE: When the mounting shaft for cut-off wheel
cannot be fixed by pressing the stopper,
turn the bolt with a spanner while pressing
the stopper.
The mounting shaft for cut-off wheel is
fixed when the stopper has been lowered.
(2) Remove the bolt, washer (A), and the wheel
washer and detach the cut-off wheel.
Fig. 12
2. Mounting the Cut-Off Wheel.
Thoroughly remove dust from the wheel washers, washer (A) and bolt, then mount the
wheel by following the dismounting procedures in reverse order.
Be sure to attach the sub cover at the end.
CAUTION: * Confirm that the stopper has returned to the retract position after
installing or removing the cut-off wheel.
* Tighten the bolt so that it doesnt come loose during operation of
the cut-off wheel.
Confirm that the bolt has been properly tightened before the
power tool is started.
Dimension of
workpiece being cut
Vise (B)
Metallic block
Vise (A)
Dimension of
metallic block
(Should be slightly smaller
than the workpiece being cut)
Stopper
Spanner
English
15
MAINTENANCE AND INSPECTION
WARNING: Always confirm that the trigger switch is turned OFF and that the power
plug has been disconnected from the receptacle before performing any
maintenance or inspection of this tool, to avoid accidental injury.
1. Replacing a cut-off wheel.
When the cut-off wheel has already become dull by frequent use, it can cause overload
to the motor.
Consequently, re-dress or replace a dull cut-off wheel to ensure cut-off efficiency.
2. Inspecting the carbon brushes (Fig. 13 and 14).
The carbon brushes in the motor are expendable parts.
If the brushes become excessively worn, motor trouble might occur.
Therefore, inspect the brushes periodically, and replace them when they have become
worn to the wear limit line, as shown in Fig. 13.
Also, keep the carbon brushes clean be so that they will slide smoothly within the brush
holders. The carbon brushes can easily be removed after disassembling the brush caps
(see Fig. 14) with a slotted (minus) screwdriver.
3. Inspecting the mounting screws.
Regularly inspect each component of the power tool for looseness.
Re-tighten mounting screws on any loose part.
WARNING: Never operate the power tool if any components are loose, to
prevent personal injury.
4. Inspecting the safety cover for condition and proper operation.
Before each use of the tool, test the safety cover (see Fig. 1) to assure that it is in good
condition and that it moves smoothly.
Never use the tool unless the safety cover operates properly, and unless it is in good
mechanical condition.
5. Storage.
Confirm that the trigger switch is turned OFF, that the power plug has been removed from
the receptacle and that the lock-off button has been removed and has been stored in a
secure place, after operation of the tool has been completed.
When the tool is not in use, keep it stored in a dry place out of the reach of children.
Fig. 13 Fig. 14
Indicates the last two number of
carbon brush
Code No.
(
81Z for 110 V 120 V
)
82Z for 220 V 240 V
Wear Limit
1/4" (6 mm)
5/8" (16 mm)
Brush Cap
English
16
6. Lubrication.
Lubricate the following sliding surfaces once a month to keep the power tool in good
operating condition for a long time (see Fig.1 and 2). Use of machine oil is recommended.
Oil supply points:
*Rotary portion of shaft.
*Rotary portion of vise.
*Rotary portion of vise-jaw.
*Quick vise.
7. Cleaning.
Periodically remove chips and other waste material from the surface of the power tool
with a damp, soapy cloth. To avoid a malfunction on the motor, protect it from contact
with oil or water.
SERVICE AND REPAIRS
All quality power tools will eventually require servicing or replacement of parts because of
wear from normal use. To assure that only authorized replacement parts will be used, and
that the double insulation system will be protected, all service (other than routine maintenance)
must be performed by an AUTHORIZED HITACHI POWER TOOL REPAIR CENTER, ONLY.
NOTE: Specifications are subject to change without any obligation on the part of HITACHI.
Español
49
ITEM NO.
PART NAME
1 MACHINE SCREW (W/WASHERS) M6 × 20
4 SAFETY COVER ASSEMBLY
6 SUB COVER
7 SCREW (G) M10 × 20
8 WASHER (A)
9 WHEEL WASHER
10 CUT-OFF WHEEL (C)
11 MACHINE SCREW M4 × 8
12 SPRING WASHER M4
13 BOLT WASHER M4
14 STOPPER SPRING
15 HITACHI LABEL
16 COLLAR (F)
17 NUT M4
18 NUT M6
19 BRUSH CAP
20 CARBON BRUSH AUTO STOP (1 PAIR)
21 BRUSH HOLDER
22 RIVET D2.5 × 4.8
23 STOPPER
26 WING BOLT M6 × 10
27 BALL BEARING 6206VV CM PS2S
28 BEARING COLLAR
29 SPINDLE
30 BALL BEARING 6201VV CM PS2S
31 BALL BEARING 6202VV CM PS2S
32 BEARING LOCK
33 ARMATURE ASSEMBLY 115V
34 FUN GUIDE
35 DUST SEAL
36 BALL BEARING 6300VV CM AV2S
37 BEARING BUSHING
38 MACHINE SCREW M6 × 22
39 SPRING WASHER M6
40 WASHER (H)
41 COLLAR (F)
42 VINYL TUBE
43 STATOR ASSEMBLY 115V
44 BRUSH TERMINAL
45 HOUSING ASSEMBLY
46 WHEEL COVER
47 TAIL COVER
49 TAPPING SCREW D4 × 10
50 NAME PLATE
51 MACHINE SCREW M4 × 10
52 CORD CLIP
53 CORD ARMOR D10.7
54 SWITCH (A) (2P PILLAR TYPE) W/LOCK
55 TAPPING SCREW (W/SP. WASHER) D5 × 80
56 SET PIECE
57 BOLT WASHER M4
58 SPRING WASHER M4
59 TAPPING SCREW D4 × 10
60 CHAIN HOOK
61 SPRING WASHER M6
62 MACHINE SCREW M6 × 20
63 SWITCH HANDLE
64 HANDLE COVER
65 BOLT WASHER M4
66 SLOTTED HD. SET SCREW M4 × 8
67 TAPPING SCREW (W/SP. WASHER) D4 × 25
68 CLUTCH
69 BOLT
ITEM NO.
PART NAME
70 BOLT WASHER M8
71 SPLIT PIN D3 × 15
72 VISE (A)
73 BOLT M10 × 20
74 BOLT WASHER M10
75 VISE (B)
76 CORD
77 CHAIN
78 RETAINING RING (E-TYPE) FOR D6 SHAFT
79 COLLAR
80 SCREW
81 MACHINE SCREW M8 × 25
82 SPRING WASHER M8
83 WASHER M8
84 SCREW HOLDER
85 BOLT WASHER M6
86 ROLL PIN D6 × 30
87 RUBBER EDGE
88 BOLT WASHER M6
89 TAPPING SCREW (W/SP. WASHER) D5 × 50
90 BASE ASSEMBLY
91 BOLT WASHER M16
92 SPRING (B)
93 SPRING (A)
94 GEAR CASE ASSEMBLY
95 HEX SOCKET SET SCREW M5 × 16
96 SHAFT
97 BASE RUBBER
98 BOLT WASHER M6
99 SPRING WASHER M6
100 MACHINE SCREW M6 × 16
101 WASHER (A)
102 SPRING WASHER M10
103 NUT M10
104 SPARK CHUTE
105 SPRING WASHER M5
106 MACHINE SCREW M5 × 10
107 NUT M8
108 HEX. SOCKET HD. BOLT M8 × 25
109 QUICK LOCK VISE ASSEMBLY
110 SPRING WASHER M8
111 STOPPER (A)
112 CAUTION PLATE
116 LOCK-OFF BUTTON
127 CAUTION PLATE
128 CAUTION PLATE (A)
133 FILTER SEAL (C)
134 RETAINRING RING (C-TYPE) FOR D15 SHAFT
501 SPANNER
Cut-Off Machine Parts List
A912
Code No. H992954-81 H
Printed in Japan
Shinagawa Intercity Tower A, 15-1, Konan 2-chome
Minato-ku, Tokyo 108-6020, Japan
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52

Hikoki CC 14 User manual

Category
Power tools
Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages