ADSWORLDWIDE
(AUDIO DESIGN SERVICES LIMITED)
St David’s House, Adcroft street, Higher Hillgate, Stockport, SK1 3HW
Tel: +44 (0161) 66 66 363 Fax: +44 (0161) 66 66 366
E-mail: [email protected]tWeb Site: WWW.ads-worldwide.net
NOTE
ADSworldwide strive to improve their products continuously, and therefore reserve the right to make
changes to drawings and technical specifications at any time without notice
CE
ISSUE: 1 8/2000
INSTALLATION AND OPERAT-
ING
INSTRUCTIONS
ADS -1015
MIXER AMPLIFIER
ADSworldwide
(AUDIO DESIGN SERVICES LIMITED)
Quality at every level
ADS - 1015 MIXER AMPLIFIER
FRONT PANEL
1 MIC1 1/4” JACK SOCKET
2 MIC2 1/4” JACK SOCKET
3 MIC1
4 MIC2
5 PHONO / AUX CD
6 TONE
7 MASTER VOLUME
8 MAINS POWER SWITCH
9 PL LED
MICROPHONE
1
2
MIC1
MIC2
PHONO / AUX CD
TONE
MASTER VOLUME
PL
1
5
4
2
3 9
8
7
6
NOTES
NOTES
ADS - 1015 MIXER AMPLIFIER
REAR PANEL
1
32
4
5
6
7
1 AC FUSE HOLDER
2 LOUDSPEAKER TERMINALS /
DC TERMINALS
3 GND
4 PHONO / AUX CD SWITCH
5 PHONO
6 AUX CD
7 AC / DC SWITCH
SAFETY INFORMATION
GENERAL INSTALLATION
WARNING : THIS APPLIANCE MUST BE EARTHED
IMPORTANT
The wires in the mains lead are coloured in accordance with the following code:
Green and yellow: Earth (E)
Blue: Neutral (N)
Brown: Live (L)
As the colours of the wires in the mains lead of the apparatus may not correspond with the coloured markings
identifying the terminals in your plug proceed as follows:
The wire which is coloured green and yellow must be connected to the terminal which is marked by the letter E
or by the safty earth symbol or coloured green and yellow.
The wire which is coloured blue must be connected to the terminal which is marked with the letter N or
coloured black.
The wire which is coloured brown must be connected to the terminal which is marked with the letter L or
coloured red.
If a 13 Amp (BS1363) plug or other type of plug is used, a 5 Amp fuse must be fitted either in the plug or at
the distribution board.
1 DO NOT expose the unit to rain or moisture. If any fluids of foreign objects
should enter the unit, disconnect the power plug immediately.
2 DO NOT run microphone cables near mains, data, telephone or 100V lines.
3 PROTECT the unit from heat and allow adequate ventilation. Place away from
direct source of heat, such as heating vents and radiators.
4 AVOID jointing the microphone cables, when this is unavoidable make sure a
good screen connector is used.
5 ALWAYS use a balanced or floating low impedance microphone terminating
in balanced input on long microphone runs.
GENERAL DESCRIPTION
ADS 1015 MIXER AMPLIFIER
The 15 watt RMS amplifier can be used on either Mains or DC power.
The amplifier has two unbalanced microphone inputs and two auxiliary inputs
for background music sources.
Amplifier controls are located on the front panel.
SPECIFICATIONS
RMS Output power 15 Watts into 8 ohm at 1 kHz
Constant Voltage output 100V
Constant Impedance output 4 - 16 ohm
Distorsion at rated power < 1% THD
Frequency responce 100Hz to 13kHz + or - 3db
Tone Control range Bass + or - 10db
Treble + or - 10db
Microphone Input
Sensitivity / Imp -48db + or - 2db/600ohm
S/N ratio > 55db
Auxiliary Input
Sensitivity -12db + or - 2db
S/N ratio >55db
Operating Conditions
Mains power supply 240V AC at 50Hz
Mains power supply 12 Volt
Dimensions (HWD) 83 x 320 x 230
Weight 3.46kg
PRIORITY CONNECTIONS
ACCESSORIES
DC Power
The equipment may be operated from a battery power source. ENSURE CORRECT
POLARITY when connecting batteries
+
+
+
+
+
–
The ADS 1015
Requires a 12 Volt
source
Loudspeaker Loading
To allow sufficient transient overload margin it is suggested that the output load
should not exceed approximately 70% of the rated power output
Description
Part Number
POSSIBLE INTERFACES
Kestrel Cabinet
Loudspeaker
Sigma Ceiling
Loudspeaker
Cougar Horn
Loudspeaker
Fire Dragon
Column
Loudspeaker
SIGNET
MICROPHONE
EC 500
MICROPHONE
F208 RDS
TUNER
PDM 603
COMPACT DISC
PLAYER
AUX2 AUX
MIC2
MIC1
12 VOLT
BATTERY
MICROPHONE
1
2
MIC1
MIC2
PHONO / AUX CD
TONE
MASTER VOLUME
PL
DC
MICROPHONE CONNECTIONS
Microphone 1
Microphone 2
Microphone 1 uses a standard 1/4” mono Jack plug.
The input is unbalanced and designed for low impedance microphones.
Microphone 2 uses a standard 1/4” mono Jack plug.
The input is unbalanced and designed for low impedance microphones.
Auxiliary 1 & 2
AUX 1 and 2 use standard phono sockets. each imput has two sockets which when con-
nected to stereo equipment mix the left and right channels to obtain a Mono signal.
Pin........Signal
Sleeve.....Screen
Pin
Sleeve
Tip
Sleeve
Tip...........Signal
Sleeve......Screen
Booster Output
Constant Voltage Output
Low Impedance
100V
For use with loudspeakers designed for 100V line systems.
Connections are to the common and 100V treminal
+
+
+
+
Com
100V
For use with loudspeakers designed for low impedance.
Connections are to Common and 4 or 16ohm terminals
NOT APPLICABLE
+
+
+
+
Com
4 ohm
16 ohm
/
