Pelonis FZ10-19JR Owner's manual

Brand: Pelonis

Model: FZ10-19JR

Type: Owner's manual

Tower Fan

MODEL: FZ10-19JR

READ AND SAVE THESE INSTRUCTIONS

Version 1.0 2015

Attention: Pictures in the IM are for reference only.

OWNER’S MANUAL

Read Rules for Safe Operation and Instructions Carefully.

CAUTION

PART FIGURE

RULES FOR SAFE OPERATION

Note: All the pictures in this manual are for explanation purpose only. Any discrepancy between

the real object and the illustration in the drawing shall be subject to the real subject.

1. Body

2. Rear base

3. Front base

4. Plastic nut

5. Power cord

WARNING

1. This appliance has a polarized plug (one blade is wider than the other). To reduce

the risk of electric shock, this plug is intended to fit in a polarized outlet only one

way. If plug does not fit fully in the outlet, reverse the plug. If it still does not fit,

contact a qualified electrician. Do not attempt to defeat this safely feature.

2. To reduce the risk of fire or electric shock, DO NOT use this fan with any solid-state

speed control devices.

1. Never insert fingers, pencils, or any other object through the grille when thefan is

running.

2. Disconnect the fan when moving it from one location to another.

3. Disconnect the fan when removing grilles for cleaning.

4. Be sure the fan is on a stable surface when operating to avoid overturning.

5. Do not use the fan by window. For rain may create electrical hazard.

6. Ensure that the fan is switched off from the supply mains before removing the grille.

The rules about cord and plug as below:

1. This product employs overload protection (fuse). A blown fuse indicates an

overload or short-circuit situation. If the fuse blows, unplug the product from the

outlet. Replace the fuse as per the user servicing instructions (follow product

marking for proper fuse rating) and check the products. If the replacement fuse

blows, a short-circuit may present and the product should be discarded or

returned to an authorized service

facility for examination and/or

repair.

2. Do not operate any fan with a

damaged cord or plug. Discard

the fan or return it to an

authorized service facility for

examination and/or repair.

3. Do not run the cord under

carpeting. Do not cover it with

thrown rugs, runners, or similar

coverings. Do not route the cord

under furniture or appliances.

Arrange the cord away from traffic

area and where it will not be

tripped over.

IMPORTANT SATETY INSTRUCTIONS

I. Remote Controller (Fig.4)

a. KEY INSTRUCTION

1. “ ” ON/OFF KEY

Press it once, the fan will turn on at normal mode.

Press this key again to turn off.

2. “ ” SPEED KEY

When the fan started, press this key repeatedly, choose

the wind speed in the order of “1-2-3”speed. The current

speed will be shown on screen.

3. “ ” MODE KEY

After the fan started, press it repeatedly to choose the mode in a cycle of

“Normal-Natural-Sleep”( ).The lights will show the chosen mode.

4. “ ” OSC/LOUVER KEY

After turning on the fan, press this key once to start oscillation. Press it again to

stop the fan at the desired direction.

ASSEMBLY INSTRUCTIONS

Fig.4

OPERATION INSTRUCTION

The outlet through

Fig.1

Fig.2 Fig.3

1. Take out the fan body and the spare parts from the box.

2. Put the front base onto the rear base and joint them together by aligning the four

posts. (See Fig. 1)

3. Detach the plastic nut (See Fig. 2) from the fan body.

4. Place the power cord through the groove on the surface of base. Then insert the fan

body into the round base. (See Fig. 3)

5. Fix the fan body on the base by screwing the plastic nut (See Fig. 2) at the bottom.

5. “ ” TIMING KEY

After the fan starts, press this key and set the time. Press it continuously to select

time from 1-7 hours with an increment of 1.

There will be signals on screen in the sequence of (=1 hour), (=2 hours),

(=3 hours), (=4 hours), (=5 hours), (=6 hours),

(=7 hours). Then the fan will automatically turn off at the setting time.

(PS: Press the timing key for the 8th time, to exit the time setting. To cancel the time

setting, press the time key continuously till the time signals disappear on screen )

b. BATTERIES

(battery not included in the packaging)

(1) Slide the battery compartment Cover.

(2) Insert the batteries, and make sure that the

batteries are placed as shown in the Fig.5.

(3) Slide back the battery cover.

NOTES: Use size “AAA” manganese or alkaline

batteries. Do not use rechargeable batteries.

c. BATTERY WARNING AS BELOW

1. “Do not dispose of batteries in fire, batteries may

explode or leak.”

2. -Do not mix old and new batteries.

3. -Do not mix alkaline, standard (carbon-zinc) or

rechargeable (nickel-cadmium) batteries.

d. REMOTE CONTROLLER OPERATION

Point the remote controller at the receptor on body of the fan and press the desired

button. The remote controller will work at distances of up to roughly five meters and

the angle of 30 degree included between right and left from the receptor.

The batteries must be removed from the remote controller before it is scrapped and

that they are disposed of safely.

e. OVERHEAT PROTECTION OF THE MOTOR

If the motor is overheated for any unexpected reasons, the thermal-fuse at the motor

windings will burn out and the fan will automatically switch off. The temperature of the

motor will no longer rise, which protects the plastic parts of the fan from deformation

under the overheat.

Fig.5

1h 2h

1h 2h 4h

4h 1h 4h 2h 4h

II. Buttons on fan body / Panel indication (Fig.6)

The buttons on the body such as ON/OFF,SPEED, MODE,

TIMER, OSCILLATION have the same functions as those

of the corresponding keys on the remote controller.

Notice:

1. When you replace the fuse, please don’t operate suddenly or overexert, or else

the product will be damage or cause accident.

2. When you feel it hard to be operated, please make sure you have got the right

way.

USER SERVICING INSTRUCTIONS

Fig.6

ON/OFF Button: Turn on/off the tower fan.

Speed Button: Press it continuously to choose “1-2-3” speed.

Mode Button: Press it repeatedly in a cycle of “Normal-Natural-Sleep”.

OSC Button: Press it to start/stop oscillation.

Timing Button: Setting time ranges from 1 to 7 hours. The fan will stop working

at your setting time.

a) Grasp the plug and remove it from the receptacle

or other outlet device. Do not unplug it by pulling

on cord.

b) Open the fuse cover. Slide to open the fuse access

cover on top of the attachment plug towards blades.

c) Remove the fuse carefully. Insert the tip of your tool into

fuse slot (close with the terminal).Then pry the fuse gradually and

slowly,but not overexert. If it’s tight, you can try it at several times and pry the

fuse little by little. When one side of the fuse has been pried, then you can get

the fuse out entirely.

d) Risk of fire. Replace the fuse only with 2.5 Amp, 125 Volt fuse.

e) Close the fuse cover. Slide to close the fuse access cover on top of the

attachment plug.

f) Risk of fire. Do not replace the attachment plug, which contains a safety

device (fuse) that should not be removed. Discard the product if the attachment

plug is damaged.

1. Be sure to unplug the fan from the electrical supply source before cleaning.

2. Plastic parts should be cleaned with mild soap and a damp cloth or sponge.

Thoroughly to remove soap film with clean water.

3. Be sure not to make water or other liquid enter inside of motor.

CLEANING

Pelonis FZ10-19JR Owner's manual

Brand: Pelonis

Model: FZ10-19JR

Type: Owner's manual

Download PDF

report

Pelonis FZ10-19JR Owner's manual

Pelonis FZ10-19JR Owner's manual

Related papers

Other documents