National Optical & Scientific Instruments Inc.
6508 Tri-County Parkway
Schertz, Texas 78154
Phone (210) 590-9010 Fax (210) 590-1104
INSTRUCTIONS FOR MODELS
106, 106-L, 106-LED
109, 109-L, 109-LED
ELEMENTARY COMPOUND MICROSCOPES
Copyright © 1/2/01
National Optical & Scientific Instrument Inc.
All models in this series have the same basic features, lenses, magnification and methods of operation. The only
differences are:
106, 109: Illumination is supplied by a plano-concave mirror.
106-L, 109-L: Illumination is supplied by a substage electric illuminator (110v 15 watt).
106-LED, 109-LED: Illumination is supplied by a substage LED illuminator.
106, 106-L, 106-LED: Have standard coarse focusing only.
109, 109-L, 109-LED: Have both coarse and fine focusing.
Models 106 and 109 supplied with
substage mirror.
Models 109, 109-L, 109-LED
feature coarse and fine focusing.
Ocular lens (eyepiece)
Eyepiece tube
Body tube
Objective turret (nosepiece)
Objective lens
Shaft of illuminator
housing
Illuminator housing
Disc diaphragm
Stage clips
Base
Inclination joint
Stage
Arm
Focusing knob
Tension adjustment collar
between focus knob and
arm of microscope
Rack stop screw
Rack stop locking nut
Models 109, 109-L,109-LED
feature inclined eyepiece.
Fine focusing
knob
LED illuminator for Models
106-LED and 109-LED
106-L Illustrated
Models supplied with substage
electrical illuminator: 106-
L and
109-L
3
Thank you for your purchase of a National microscope. It is a well built, precision instrument and carefully checked to assure
that it reaches you in good condition. It is designed for ease of operation and years of carefree use. The information in this
manual probably far exceeds what you will need to know in order to operate and maintain your microscope. However, it is
provided to answer questions, which might arise, and to help you avoid any maintenance expense that may be unnecessary.
Carefully read instructions before operating microscope. Nomenclature used to describe components and controls are
identified on opposite page of the manual.
UNPACKING
Do not discard Styrofoam container or packing materials. Save in case instrument needs to be transported or shipped
for repairs. Remove microscope and dustcover from container. Remove all tape and packing material used to protect
microscope during shipment. Make certain lens surfaces do not come in contact with dirt, fingerprints or oil. Damage of lens
surfaces occurs when they come in contact with such contaminants, and image quality is reduced.
DESCRIPTION OF COMPONENTS
A. OCULAR LENS (eyepiece): Lens closest to the eye, magnifies the primary image formed by the objective lens
B. OBJECTIVE LENS: Lens closest to the specimen, forms the first magnified image of the specimen.
C. OBJECTIVE TURRET (nosepiece): Revolving turret designed to hold objective lenses, permits changes of magnification
by rotating different powered objective lenses into optical path.
D. STAGE CLIPS: Two locked-on clips hold specimen slide in place on stage.
E. STAGE: Platform of the microscope where the specimen slide is placed on stage.
F. DISC DIAPHRAGM: Rotating disc located below stage, with 6 holes of various apertures, designed to help achieve
optimum resolution of the objective lens. Smaller apertures used for lower magnifications, and larger apertures used for
higher magnifications.
G. SAFETY RACK STOP: When properly adjusted, controls maximum downward travel of body tube while focusing,
prevents higher power objectives from breaking specimen slides, prevents damage to objective lenses. This safety rack
stop has been pre-adjusted at the factory.
H. FOCUSING KNOBS: Focusing knobs located on each side of arm, when turned, raise or lower body tube to bring
specimen into focus.
I. Model 109 has coarse focus knobs described above, plus fine focus knobs (smaller knobs) located on both sides of arm
right below coarse focus knobs. These permit precise adjustment for sharper focus of image.
J. ILLUMINATION: Depending on model purchased, microscope is provided with either a plano-concave mirror or built-in
electrical illuminator.
1. Mirror provides illumination of specimen by reflecting light from an artificial source or natural light.
2. Substage electrical illuminator provides constant, reliable pre-focused illumination.
3. Sub-stage cordless LED illuminator provides illumination equal to 20 watt tungsten bulb. Features ON/OFF switch
with rheostat intensity control, rechargeable AA Nickel Hydride batteries and auto recharger.
OPERATION
A. Always carry microscope by grasping arm with one hand and placing other hand under base.
B. Place microscope directly in front of you in a manner which permits you to comfortably look into the eyepiece. Position
the microscope with the arm facing you so that focusing knobs are most convenient to reach, and you do not block light
if using a model that has a mirror for illumination.
C. Note that model 106 can be tilted at the inclination joint to provide comfortable viewing angle. Model 109 has a special
inclined eyepiece so that it is not necessary to tilt microscope at inclination joint.
4
D. First, assure that light is available for illuminating the specimen.
1. Mirror models
a. Assure that there is a good nearby source of light (overhead light, tabletop lamp or reasonably bright natural
light).
b. Position the concave (curved) side of mirror upward.
c. Look through eyepiece and tilt the entire mirror (tilts on either of two axis) until light appears to fill the entire
field of view.
2. Electric illuminator models.
a. Plug polarized 2 conductor plug into a standard 120 volt AC three-wire grounded outlet.
b. Rotate switch located on cord to ON position.
c. In case of equipment malfunction, see Trouble Shooting Procedure located at the back of this manual.
3. LED cordless illuminator models.
a. Your microscope has special LED illumination that is powered by 3 rechargeable AA nickel metal hydride
batteries (supplied). These batteries may be recharged, as required, using the recharger (supplied). Each set
of batteries may be recharged approximately 1000 times before replacing, and each charge will provide up to
50 hours of microscope operation. The LED component (bulb) will last for up to 100,000 hours before
replacement is required.
WARNING
DO NOT USE regular AA alkaline batteries. Use of other than rechargeable AA nickel metal hydride
batteries could result in batteries exploding during recharge. ONLY USE THE SUPPLIED SWITCHING
BATTERY RECHARGER WITH AUTOMATIC “TRICKLE CHARGE”.
b. It is recommended that you charge the batteries before initial use and after prolonged storage as the batteries
may have discharged. Plug output cord from battery charger into DC recharging socket located on side of LED
illuminator. Your automatic switching recharger operates on 100 to 240 volts AC 50/60 Hz. Plug recharger into
your AC wall outlet. Battery recharger is also equipped with an automatic “trickle charge” feature, the red LED
indicator lamp located on recharger will be illuminated when batteries are receiving maximum charge. After
batteries are charged, the red LED indicator lamp will turn to green and charger automatically switches to
“trickle charge”. The charger can be left plugged in, but for safety reasons it is a good idea to disconnect the
charger from the AC wall outlet and the output cord from recharging socket after 12 hours. Batteries and
charger may feel warm when charging, and unplugging the recharger is a safety precaution.
c. Turn illuminator “ON” by simply rotating the adjustable rheostat control knob located on side of illuminator.
Rotating the rheostat control knobs varies the intensity of the LED illuminator.
Note that your microscope can be used during recharging.
E. Rotate focus knobs to move eyepiece tube up (away) from stage as far as possible.
F. Place specimen slide, cover slip facing up, on stage with specimen centered over hole in middle of stage.
G. Rotate disc diaphragm to position the largest aperture under the hole in center of stage.
H. Turn the objective turret until the 4x (smallest) objective lens clicks into position in the optical path.
I. Note that each time you change from one objective lens to another you should turn the turret until you hear the click,
which indicates that the lens is properly indexed in the optical path.
J. While looking through the eyepiece, rotate focusing knobs until specimen comes into focus. If image does not appear in
field of view, move specimen slide slightly on stage until image appears in field of view.
K. If using Model 109 which has both coarse and fine focus knobs, you can now adjust fine focus knobs to obtain optimum
image sharpness.
L. Turn the disc diaphragm, observing that different apertures affect the sharpness of the image. Turn diaphragm until
sharpest possible image is obtained. When turning the disc diaphragm, you should hear a click as each aperture comes
5
into proper position under the hole in center of stage. If aperture is not properly positioned, you will observe shadows in
the field of view when looking through the microscope.
M. Changing magnification
1. Note that each of the three objectives have a different color ring. This permits the teacher to instruct the class to
switch magnifications by referring to the color of the ring.
2. Total magnification obtained with each objective lens is determined by multiplying the magnification of the eyepiece
times the magnification of the objective. Keep in mind that as magnification is increased, field of view (area of the
specimen seen when looking through the microscope) decreases. You will find that you use the lower
magnifications at most times. Always use the lowest magnification (4x objective) when first focusing on a new
specimen slide, as this low magnification provides the biggest field of view, there by making it easier to find and
position the specimen within the field of view.
10x eyepiece x 4x objective = 40 times mag. (biggest field of view), red color code ring
10x eyepiece x 10x objective = 100 times mag. (smaller field of view), yellow color code ring
10x eyepiece x 40x objective = 400 times mag. (smallest field of view), blue color code ring
3. To change magnification:
a. Rotate revolving nosepiece to position 10x objective into optical path. Some slight adjustment of focusing knob
may be required.
b. Rotate revolving nosepiece to position 40x objective into optical path. Some slight adjustment of focusing knob
may be required.
4. Note: Take care when rotating 40x objective into place. This is the longest lens and has a spring retractable
mechanism, which retracts slightly into its housing if the front of the lens comes in contact with the specimen slide
while focusing the microscope. This prevents damage to the lens or slide.
MAINTENANCE
WARNING: For your own safety, when servicing models with electric and LED illuminators, turn switch to OFF
position and remove plug from power source before maintaining microscope. If the power cord is worn, cut or
damaged in anyway, have it replaced at once to avoid shock or fire hazard.
OPTICAL MAINTENANCE
A. Do not attempt to disassemble any lens components. Consult an expert technical service company when repairs not
covered by these instructions are needed.
B. Prior to cleaning any lens surface, brush dirt and lint off lens surface with camel hair brush or compressed air. Use of air
in a can, available at most computer stores, is good source of clean air.
C. Do not remove eyepiece lens or objective lenses from microscope. Clean only the outer lens surface by breathing on
lens to dampen surface, then wipe with lens paper or cotton swab. Avoid wiping lens surface while dry, as lenses are
scratched very easily.
MECHANICAL MAINTENANCE
A. Rack stop adjustment: Rack stop has been pre-adjusted at the factory, and should not require readjustment.
B. Coarse focus tension adjustment: This adjustment prevents the body tube from drifting down on its own weight and
causing the image to move out to focus during viewing.
1. Tension adjustment collar is located between arm and coarse focus knob on left side of microscope.
2. With a small jeweler’s screwdriver, loosen the set screw located in one of the four holes located on tension
adjustment collar.
6
3. To tighten tension, turn collar in clockwise direction. Use of wide rubber band will provide a better grip on the
tension adjustment collar. It is advisable to leave controls as loose as possible, tightening only enough to keep
body tube from drifting down and out of focus from its own weight.
C. Metal parts: Use a clean, damp cloth to remove dust or dirt from metal part followed by a dry cloth.
ELECTRICAL MAINTENANCE (for models with electric substage illuminator)
WARNING: For your safety, turn switch off and remove plug from power source before replacing bulb. Make sure
that illuminator housing and lamp are cool before servicing.
A. On the bottom of illuminator housing shaft, locate locking screw that secures shaft portion to main illuminator housing.
Using screwdriver, remove completely.
B. Pull straight out on shaft to remove from main illuminator housing.
C. Note that lamp does not screw out. Remove by depressing lamp slightly and rotate in counter-clockwise direction until it
pops up slightly.
D. Replace with a 115-130v 15 watt lamp with double contact, medium bayonet base. This is a standard, commonly used
microscope replacement bulb. It is also available from National, specifying replacement part #800-101. Do not use
higher than 15 watt bulb. Depress lamp slightly and rotate in clockwise direction.
E. Carefully wipe new lamp to insure that it is clean and free of all fingerprints. Gently depress lamp into socket and rotate
counter clockwise.
F. Insert shaft into main illuminator housing and secure with locking screw.
CORDLESS ILLUMINATOR (for models with rechargeable illuminators)
The extent of electrical maintenance, by other than a qualified technician, should be battery recharging and battery
replacement. Before maintenance, be sure that recharger is not connected to microscope.
A. Recharging Batteries: Plug output cord from battery charger into DC recharging socket located on side of illuminator.
Your automatic switching recharger operates on 100 to 240 volts AC 50/60 Hz, plug recharger into your AC wall outlet.
The red LED indicator lamp located on recharger will be illuminated when batteries are receiving maximum charge.
After batteries are charged, the red LED indicator lamp will turn to green and charger automatically switches to “trickle
charge”. The charger can be left plugged in, but for safety reasons it is a good idea to disconnect the charger from the
AC wall outlet and the output cord from recharging socket after 12 hours. Batteries and charger may feel warm when
charging, and unplugging the recharger is a safety precaution.
B. Replacing Batteries: Your microscope includes 3 rechargeable AA nickel hydride batteries. These may be recharged
up to 1000 times, but if you observe that a recharge is providing significantly less than 40 hours of operation, it is
probably time to replace the batteries.
IMPORTANT WARNING: DO NOT USE REGULAR ALKALINE BATTERIES IN THIS MICROSCOPE. ANY ATTEMPT
TO RECHARGE ALKALINE TYPE BATTERIES COULD RESULT IN BATTERIES EXPLODING.
Gently lay microscope on its side or back. Observe battery compartment cover located on bottom of illuminator. Using
a small Phillips screwdriver, carefully remove the two Phillips screws that secure battery cover to bottom of illuminator.
Slide battery cover straight back to remove and expose batteries. Remove all 3 batteries and replace with new
rechargeable AA nickel metal hydride batteries, making certain to insert with correct polarity according to markings on
battery holder. Replace battery cover and secure with the two Phillips screws.
Follow instructions on new battery packaging to determine if they are already charged, or if they should be charged
before initial use. If recharging is required, following directions in “A.” above.
C. Replacing LED Element: Do not attempt to disassemble any “LED” bulb components. Consult an expert technical
service company when the LED “bulb” needs replacement or return the illuminator to National for repair.
An LED “bulb” will last up to 100,000 hours, so you don’t have to do this exercise very often.
7
TROUBLESHOOTING PROCEDURES
PROBLEM
REASON FOR PROBLEM
SOLUTION
No Illumination
(All Models)
Disc diaphragm has not “clicked” into
proper position and is blocking light
source beneath stage
Turn disc diaphragm until it “clicks” into
position
(Non illuminated models) Mirror not properly positioned to
direct light through microscope
Reposition mirror
(115 Volt Electric Models) Outlet inoperative
AC power cord not connected
Lamp burned out
Have qualified service technician repair
outlet
Plug into outlet
Replace lamp
(Rechargeable LED Models)
Batteries fully discharged
Batteries will not hold a charge
On/Off rheostat control not turned far
enough
LED bulb burned out
Recharge batteries
Replace batteries
Turn rheostat to On position and rotate to
increase light intensity
Have qualified technical service company
change bulb
Image does not remain in focus
Eyepiece tube drops under its own
weight.
Adjust tension of coarse focus knob (see
maintenance)
Image does not focus Cover slip on specimen slide too
thick.
Use 0.17mm thick cover slip.
(No. 1 cover slip)
Slide upside down. Place slide on stage with cover slip facing
up.
Poor resolution
(image not sharp)
Objective lenses dirty.
Clean objective lenses.
Eyepiece lens dirty.
Clean eyepiece lenses.
Too much light.
Adjust disc diaphragm
Spots in field of view.
Eyepiece lens dirty.
Clean eyepiece lenses.
Specimen slide dirty.
Clean slide.
8
OPTIONAL ACCESSORIES AND PARTS:
#800-101 Replacement bulb, 115v 15 watt, D.C. medium bayonet base for electric illuminator
#900 Replacement substage illuminator, 115v 15 watt
#906-LED Replacement substage LED illuminator for cordless operation
WARRANTY - 5 YEAR LIMITED WARRANTY
Please see our website,
www.nationaloptical.com, for complete warranty details and exclusions.
(Revised 1/18/13)
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
National 109-L Instructions Manual
- Type
- Instructions Manual
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
National 111 Instructions Manual
-
-
-
-
National 138 Instructions Manual
-
National 158-LED Instructions Manual
-
-
-
-
Other documents
-
Rio MMIR Datasheet
-
Motic RED50X User manual
-
-
Lavish Home HW1000024 Installation guide
-
Carson LM-20 User guide
-
SWIFT SW100 Compound Kids Microscope User guide
-
Hey! Play! M330022 Operating instructions
-
Carson MM-24 User guide
-
-
