Annin Flagmakers 242 Installation guide

Brand
Annin Flagmakers
Model
242
Type
Installation guide

Annin Flagmakers 242 is a versatile and easy-to-use spinning pole designed for displaying traditional style flags (heading and 2 grommets) or banner style flags (pole sleeve). It consists of two sections that can be easily assembled and disassembled, making it convenient for storage and transportation. The pole is made of durable materials and is capable of holding flags up to 3x5 feet in size.

Annin Flagmakers 242 is a versatile and easy-to-use spinning pole designed for displaying traditional style flags (heading and 2 grommets) or banner style flags (pole sleeve). It consists of two sections that can be easily assembled and disassembled, making it convenient for storage and transportation. The pole is made of durable materials and is capable of holding flags up to 3x5 feet in size.

Instructions for Assembly of Spinning Poles
Instructions for Assembly of Spinning Poles
If ornament is not on pole or if you wish to change ornament
1. Securely grasp the 3-inch metal rod that protrudes from the bottom of the top half of the pole.
2. Screw the ornament onto the top of the pole as far as it will go, being careful not to cross thread or over tighten.
To assemble top and bottom of pole together
1. Locate dimple in open end of lower section
2. Slide 3-inch plastic rod that protrudes from the top section into the bottom section, lining up L-shaped groove with dimple in
bottom section.
3. Press two sections of pole against each other until flush. CAUTION: Do not jam pole sections together
4. Securely grasp the ornament on the top half of the pole with one hand and the bottom section of pole with the other hand and
GENTLY turn bottom section so that it slides into the L-shaped groove. Be careful not to over tighten.
5. The two sections of the pole should now be locked and the top half of pole should spin freely.
To Mount Traditional Style Flag (heading and 2 grommets) on Pole
1. Remove set -screws from flag fasteners, slip first fastener up bottom of flagpole and position just below swivel clip. Note: Swivel
clip and snap hooks are not used with traditional style flag.
2. Position opening in fastener under the top grommet of flag.
3. Replace set- screw in fastener through grommet of flag thereby holding flag snug against pole.
4. Repeat with lower grommet.
To Mount Banner Style Flag (Pole Sleeve) on Pole
1. Slide pole through banner sleeve
2. Locate pre-slit tab sewn inside top of banner sleeve
3. Attach snap hook (on swivel clip) to pre-slit tab. Note: Flag fasteners are not used with banner style flags.
Caution: Spinning poles are not to be used with flags heavier than nylon or larger than 3x5 feet. Flags should not be flown in
extreme wind conditions.
To Disassemble Spinning Pole
1. Hold ornament firmly in one hand and bottom section of pole in the other hand.
2. Line up dimple on bottom section of pole with arrow on joint.
3. Gently pull sections apart. The two sections should come apart easily.
Caution: Do not use force. If top and bottom do not separate easily, repeat step 1 and turn pole slightly in either direction while
pulling gently.
  • Page 1 1
  • Page 2 2

Annin Flagmakers 242 Installation guide

Brand
Annin Flagmakers
Model
242
Type
Installation guide

Annin Flagmakers 242 is a versatile and easy-to-use spinning pole designed for displaying traditional style flags (heading and 2 grommets) or banner style flags (pole sleeve). It consists of two sections that can be easily assembled and disassembled, making it convenient for storage and transportation. The pole is made of durable materials and is capable of holding flags up to 3x5 feet in size.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents