Indesit SDS 1722 V/HA User manual

Type
User manual
Italiano Italiano
Italiano Italiano
Italiano
Istruzioni per l’uso
FRIGORIFERO
SDS 1721xx
SDS 1722xx
Sommaire
Mode d’emploi, 1
Assistance, 2
Description de l’appareil, 5
Réversibilité des portes, 7
Installation, 16
Accessoires, 16
Mise en marche et utilisation, 17
Entretien et soin, 17
Précautions et conseils, 18
Anomalies et remèdes, 19
Contents
Operating Instructions, 1
Assistance, 2
Description of the appliance, 4
Reversible doors, 7
Installation, 12
Accessories, 12
Start-up and use, 13
Maintenance and care, 13
Precautions and tips, 14
Troubleshooting, 15
Sommario
Istruzioni per l’uso, 1
Assistenza, 2
Descrizione dell’apparecchio, 4
Reversibilità apertura porte, 7
Installazione, 8
Accessori, 8
Avvio e utilizzo, 9
Manutenzione e cura, 9
Precauzioni e consigli, 10
Anomalie e rimedi, 11
English English
English English
English
Operating Instructions
FRIDGE
Français Français
Français Français
Français
Mode d’emploi
REFRIGERATEUR
Nederlands Nederlands
Nederlands Nederlands
Nederlands
Gebruiksaanwijzingen
KOELKAST
Inhoud
Gebruiksaanwijzingen, 1
Service, 3
Beschrijving van het apparaat, 5
Draairichting deuren verwisselbaar, 7
Installatie, 20
Toebehoren, 20
Starten en gebruik, 21
Onderhoud en verzorging, 21
Voorzorgsmaatregelen en advies, 22
Storingen en oplossingen, 22
Sumario
Manual de instrucciones, 1
Asistencia, 3
Descripción del aparato, 6
Reversibilidad de la apertura de las puertas, 7
Instalación, 24
Accesorios, 24
Puesta en funcionamiento y uso, 25
Mantenimiento y cuidados, 25
Precauciones y consejos, 26
Anomalías y soluciones, 27
Español Español
Español Español
Español
Manual de instrucciones
FRIGORÍFICO
2
Assistenza
Prima di contattare l’Assistenza:
Verificare se l’anomalia può essere risolta autonomamente
(
vedi Anomalie e Rimedi
).
In caso negativo, contattare il Numero Unico Nazionale
199.199.199.
Comunicare:
il tipo di anomalia
il modello della macchina (Mod.)
il numero di serie (S/N)
Queste informazioni si trovano sulla targhetta caratteristiche
posta nel vano frigorifero in basso a sinistra.
Non ricorrete mai a tecnici non autorizzati e rifiutate sempre
l’installazione di pezzi di ricambio non originali.
Assistenza Attiva 7 giorni su 7
Se nasce il bisogno di assistenza o manutenzione basta
chiamare il Numero Unico Nazionale 199.199.199* per essere
messi subito in contatto con il Centro Assistenza Tecnica più
vicino al luogo da cui si chiama.
È attivo 7 giorni su 7, sabato e domenica compresi, e non lascia
mai inascoltata una richiesta.
* Al costo di 14,25 centesimi di Euro al minuto (iva inclusa) dal
Lun. al Ven. dalle 08:00 alle 18:30, il Sab. dalle 08:00 alle 13:00 e
di 5,58 centesimi di Euro al minuto (iva inclusa) dal Lun. al Ven.
dalle 18:30 alle 08:00, il Sab. dalle 13:00 alle 08:00 e i giorni
festivi, per chi chiama dal telefono fisso.
Per chi chiama da radiomobile le tariffe sono legate al piano
tariffario dell’operatore telefonico utilizzato.
Le suddette tariffe potrebbero essere soggette a variazione da
parte dell’operatore telefonico; per maggiori informazioni
consultare il sito www.indesit.com.
Assistance
Before calling for Assistance:
Check if the malfunction can be solved on your own (
see
Troubleshooting
).
If after all the checks, the appliance still does not operate or
the problem persists, call the nearest Service Centre
Communicating:
type of malfunction
appliance model (Mod.)
serial number (S/N)
This information can be found on the data plate located on the
bottom left side of the refrigerator compartment.
Never call on unauthorized technicians and always refuse
spare parts which are not originals.
Assistance
Avant de contacter le centre d’Assistance :
Vérifiez si vous pouvez résoudre l’anomalie vous-même (
voir
Anomalies et Remèdes
).
Si, malgré tous ces contrôles, l’appareil ne fonctionne
toujours pas et si l’inconvénient persiste, appelez le service
après-vente le plus proche.
Signalez-lui :
le type d’anomalie
le modèle de l’appareil (Mod.)
le numéro de série (S/N)
Vous trouverez tous ces renseignements sur l’étiquette
signalétique placée dans le compartiment réfrigérateur en bas à
gauche.
Ne vous adressez jamais à des techniciens non agréés et
exigez toujours l’installation de pièces détachées originales.
- modello
- model
- modèle
- model
- modelo
- numero di serie
- serial number
- numéro de série
- serienummer
- número de serie
4
7
1
4
6
9
2
8
609eps
3
5
Descrizione dell’apparecchio
Vista d’insieme
Le istruzioni sull’uso valgono per diversi modelli per cui è
possibile che la figura presenti particolari differenti rispetto a
quelli dell’apparecchio acquistato. La descrizione degli oggetti
più complessi si trova nelle pagine seguenti.
1 PIEDINO di regolazione.
2 Cassetto FRUTTA e VERDURA
3 WINE RACK*.
4 RIPIANO•.
5 PURE WIND.
6 Manopola REGOLAZIONE DELLA TEMPERATURA.
7 Balconcino estraibile con coperchio e PORTAUOVA*.
8 Balconcino estraibile PORTAOGGETTI•.
9 Balconcino BOTTIGLIE•.
• Variabili per numero e/o per posizione.
* Presente solo in alcuni modelli.
Description of the appliance
Overall view
The instructions contained in this manual are applicable to
different model refrigerators. The diagrams may not directly
represent the appliance purchased. For more complex features,
consult the following pages.
1 Levelling FEET
2 FRUIT and VEGETABLE bin
3 WINE RACK*.
4 SHELVES•
5 PURE WIND.
6 TEMPERATURE REGULATING Knob
7 Removable lidded shelf with EGG TRAY
8 Removable multipurpose SHELVES•.
9 BOTTLE shelf•.
• Varies by number and/or position.
* Available only on certain models.
12
GB
Installation
! Before placing your new appliance into operation please read
these operating instructions carefully. They contain important
information for safe use, for installation and for care of the
appliance.
! Please keep these operating instructions for future reference.
Pass them on to possible new owners of the appliance.
Positioning and connection
Positioning
1. Place the appliance in a well-ventilated humidity-free room.
2. Do not obstruct the rear fan grills. The compressor and
condenser give off heat and require good ventilation to
operate correctly and save energy.
3. Leave a space of at least 10 cm between the top part of the
appliance and any furniture above it, and at least 5 cm
between the sides and any furniture/side walls.
4. Ensure the appliance is away from any sources of heat (direct
sunlight, electric stove, etc.).
5. In order to maintain the correct distance between the
appliance and the wall behind it, fit the spacers supplied in
the installation kit, following the instructions provided.
Levelling
1. Install the appliance on a level and rigid floor.
2. If the floor is not perfectly horizontal, adjust the refrigerator by
tightening or loosening the front feet.
Electrical connections
After the appliance has been transported, carefully place it
vertically and wait at least 3 hours before connecting it to the
electricity mains. Before inserting the plug into the electrical
socket ensure the following:
The appliance is earthed and the plug is compliant with the law.
The socket can withstand the maximum power of the
appliance, which is indicated on the data plate located on the
bottom left side of the fridge (e.g. 150 W).
The voltage must be in the range between the values
indicated on the data plate located on the bottom left side
(e.g. 220-240V).
The socket is compatible with the plug of the appliance. If the
socket is incompatible with the plug, ask an authorised
technician to replace it (
see Assistance
). Do not use
extension cords or multiple sockets.
! Once the appliance has been installed, the power supply cable
and the electrical socket must be easily accessible.
! The cable must not be bent or compressed.
! The cable must be checked regularly and replaced by
authorised technicians only (see Assistance).
!
The manufactur The manufactur
The manufactur The manufactur
The manufactur
er declines any liability should these safetyer declines any liability should these safety
er declines any liability should these safetyer declines any liability should these safety
er declines any liability should these safety
measurmeasur
measurmeasur
measur
es not be observed.es not be observed.
es not be observed.es not be observed.
es not be observed.
Stability bracket
WARNING: To prevent the fridge from tilting forwards, it must be
held in place with the stability bracket supplied.
This is the responsibility of the customer.
Fixed to the floor or wall at the rear of the fridge, the stability
bracket hooks onto the compressor mounting plate holding the
fridge secure.
The stability bracket must be installed securely in accordance
with these instructions BEFORE using the fridge.
Note: The fridge is heavy so care must be taken when
moving it.
1. Position the fridge in its chosen location.
2. Looking from the front of the fridge, mark the position of the
left hand panel.
3. Move the fridge far enough away to get clear access to the
back wall.
4. In order to clear components on the compressor mounting
plate, the stability bracket must be positioned on the floor
between 100 - 200mm to the right of the left hand panel mark.
5. Mark and drill the fixing holes and insert suitable fixings to
hold the bracket firm.
6. Carefully re-position the fridge. Make sure that the
compressor mounting plate locates into the stability bracket.
Accessories
TEMPERATURE Indicator light*: to identify the coldest area in
the refrigerator.
1. Check that OK appears clearly on the indicator light (
see
diagram
).
2. If the word “OK” does not appear it means that the temperature
is too high: adjust the REFRIGERATOR OPERATION knob to a
higher position (colder) and wait approximately 10 hours until
the temperature has been stabilised.
3. Check the indicator light again: if necessary, readjust it
following the initial process. If large quantities of food have
been added or if the refrigerator door has been opened
frequently, it is normal for the indicator not to show OK. Wait at
least 10 hours before adjusting the REFRIGERATOR
OPERATION knob to a higher setting.
GB
13
Start-up and use
Starting the appliance
! Before starting the appliance, follow the installation
instructions (
see Installation
).
! Before connecting the appliance, clean the compartments and
accessories well with lukewarm water and bicarbonate.
1. Insert the plug into the socket and ensure that the internal
light illuminates.
2. Turn the TEMPERATURE ADJUSTMENT knob to an average
value. After a few hours you will be able to put food in the
refrigerator.
Setting the temperature
The temperature inside the refrigerator compartment automatically
adjusts itself according to the position of the thermostat knob.
1 = warmest
MAX = coldest
We recommend, however, a medium position.
The cooling section of the refrigerator is located inside the back wall
of the refrigerator compartment for increased space and improved
aesthetics. During operation, the back wall will be covered in frost or
water droplets depending on whether the compressor is operating
or paused. Do not worry, the refrigerator is functioning normally.
PURE WIND
It is recognizable due to the presence of the mechanism on the
top part of the refrigerator compartment
(see diagram)
.
A
B
B
B
A
The PURE WIND System maintains a constant fridge temperature to
keep food fresher for longer and will quickly restore the temperature
to the correct level, even if the door is opened frequently: the blown
air (A) is cooled when it comes into contact with the cold wall,
whereas the hotter air (B) is sucked up (see diagram).
Using the refrigerator to its full potential
Use the TEMPERATURE ADJUSTMENT knob to adjust the
temperature (
see Description
).
Place only cold or lukewarm foods in the compartment, not
hot foods (
see Precautions and tips
).
Remember that cooked foods do not last longer than raw
foods.
Do not store liquids in open containers. They will increase
humidity in the refrigerator and cause condensation to form.
SHELVES: with or without grill.
Due to the special guides the shelves are removable and the
height is adjustable (
see diagram
), allowing easy storage of
large containers and food. Height can be adjusted without
complete removal of the shelf.
Food hygiene
1. Once you have bought your food, remove all external
packaging made of paper/cardboard or other wrappers,
which could introduce bacteria or dirt inside your refrigerator.
2. Protect the food, (especially easily perishable items and those
that have a strong smell), in order to avoid contact between
them, thereby removing both the possibility of germ/bacteria
contamination as well as the diffusion of strong odours inside
the fridge.
3. Store all food in such a way as to ensure air can circulate
freely between different items.
4. Keep the inside of your fridge clean, taking care not to use
oxidiser or abrasive products.
5. Remove all food past its expiry date from the refrigerator.
6. For the correct preservation of food, all easily perishable items
(soft cheeses, raw fish, meat, etc.) should be stored in the
coldest zone of the fridge compartment, i.e. just above the
salad crisper where the temperature indicator is situated.
Maintenance and care
Switching the appliance off
During cleaning and maintenance it is necessary to disconnect
the appliance from the electricity supply.
It is not sufficient to set the temperature adjustment knobs on
OFF (appliance off) to eliminate all electrical contact.
Cleaning the appliance
The external and internal parts, as well as the rubber seals
may be cleaned using a sponge that has been soaked in
lukewarm water and bicarbonate of soda or neutral soap. Do
not use solvents, abrasive products, bleach or ammonia.
The removable accessories may be soaked in warm water
and soap or dishwashing liquid. Rinse and dry them carefully.
The back of the appliance may collect dust which can be
removed by delicately using the hose of a vacuum cleaner set
on medium power. The appliance must be switched off and
the plug must be pulled out before cleaning the appliance.
Avoiding mould and unpleasant odours
The appliance is manufactured with hygienic materials which
are odour free. In order to maintain an odour free refrigerator
and to prevent the formation of stains, food must always be
covered or sealed properly.
If you want to switch the appliance off for an extended period
of time, clean the inside and leave the doors open.
14
GB
Defrosting the appliance
! Follow the instructions below.
Do not speed up the defrosting process by using any devices or
tools other than the scraper provided, you may damage the
refrigeration circuit.
The refrigerator has an automatic defrosting function: water is
ducted to the back of the appliance by a special discharge outlet
(
see diagram
) where the heat produced by the compressor
causes it to evaporate. It is necessary to clean the discharge
hole regularly so that the water can flow out easily.
Replacing the light bulb
To replace the light bulb in the refrigerator compartment, pull out
the plug from the electrical socket. Follow the instructions below.
Access the light bulb by removing the cover as indicated in the
diagram. Replace it with a similar light bulb within the power
range indicated on the cover (15W or 25W).
1 1
2
Precautions and tips
! The appliance was designed and manufactured in compliance
with international safety standards. The following warnings are
provided for safety reasons and must be read carefully.
This appliance complies with the following Community Directives:
- 73/23/EEC of 19/02/73 (Low Voltage) and subsequent
amendments;
-89/336/EEC of 03.05.89 (Electromagnetic Compatibility) and
subsequent amendments;
- 2002/96/CE..
General safety
The appliance was designed for domestic use inside the
home and is not intended for commercial or industrial use.
The appliance must be used to store and freeze food products
by adults only and according to the instructions in this manual.
The appliance must not be installed outdoors, even in
covered areas. It is extremely dangerous to leave the
appliance exposed to rain and storms.
Do not touch the appliance with bare feet or with wet or moist
hands and feet.
Do not touch the internal cooling elements: this could cause
skin abrasions or frost/freezer burns.
When unplugging the appliance always pull the plug from the
mains socket, do not pull on the cable.
Before cleaning and maintenance, always switch off the
appliance and disconnect it from the electrical supply. It is not
sufficient to set the temperature adjustment knobs on OFF
(appliance off) to eliminate all electrical contact.
In the case of a malfunction, under no circumstances should
you attempt to repair the appliance yourself. Repairs carried
out by inexperienced persons may cause injury or further
malfunctioning of the appliance.
Do not use devices or tools other than the special scraper
provided inside the compartments.
Do not put ice cubes taken directly from the freezer into your
mouth.
This appliance is not intended for use by persons (including
children) with reduced physical, sensory or lack of experience
and knowledge unless they have been given supervision or
instruction concerning use of the appliance by a person
responsible for their safety. Children should be supervised to
ensure that they do not play with the appliance.
Keep packaging material out of the reach of children! It can
become a choking or suffocation hazard.
Disposal
Observe local environmental standards when disposing
packaging material for recycling purposes.
The European Directive 2002/96/EC on Waste Electrical and
Electronic Equipment (WEEE), requires that old household
electrical appliances must not be disposed of in the normal
unsorted municipal waste stream. Old appliances must be
collected separately in order to optimise the recovery and
recycling of the materials they contain and reduce the impact
on human health and the environment. The crossed out
“wheeled bin” symbol on the product reminds you of your
obligation, that when you dispose of the appliance it must be
separately collected. Consumers should contact their local
authority or retailer for information concerning the correct
disposal of their old appliance.
Respecting and conserving the environment
Install the appliance in a fresh and well-ventilated room.
Ensure that it is protected from direct sunlight and do not
place it near heat sources.
Try to avoid keeping the door open for long periods or
opening the door too frequently in order to conserve energy.
Do not fill the appliance with too much food: cold air must
circulate freely for food to be preserved properly. If circulation
is impeded, the compressor will work continuously.
Do not place hot food directly into the refrigerator. The internal
temperature will increase and force the compressor to work
harder and will consume more energy.
Regularly check the door seals and wipe clean to ensure they
are free of debris and to prevent cold air from escaping (
see
Maintenance
).
GB
15
Troubleshooting
If the appliance does not work, before calling for Assistance (see
Assistance), check for a solution from the following list.
The internal light does not illuminate.
The plug has not been inserted into the electrical socket, or
not far enough to make contact, or there is no power in the
house.
The TEMPERATURE CONTROL Knob is on OFF setting.
The refrigerator do not cool well.
The door do not close properly or the seals are damaged.
The door are opened too frequently.
The TEMPERATURE ADJUSTMENT knob is not in the correct
position
The refrigerator have been over-filled.
The food inside the refrigerator is beginning to freeze.
The TEMPERATURE ADJUSTMENT knob is not in the correct
position.
The food is in contact with the back inside wall of the
refrigerator.
The PURE WIND fan does not rotate
The PURE WIND system is only activated automatically when
it becomes necessary to restore perfect operational
conditions inside the refrigerator compartment.
The motor runs continuously.
The door is not closed properly or is continuously opened.
The outside ambient temperature is very high.
The appliance makes a lot of noise.
The appliance has not been installed on a level surface (
see
Installation
)
.
The appliance has been installed between cabinets that
vibrate and make noise.
The internal refrigerant makes a slight noise even when the
compressor is off. This is not a defect, it is normal.
The back wall of the refrigerator unit is covered in frost or
droplets of water
This shows the appliance is operating normally.
There is water at the bottom of the refrigerator.
The water discharge hole is blocked (
see Maintenance
).
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28

Indesit SDS 1722 V/HA User manual

Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI