Specifications
1
Specifications
Machine Parts Diagram
Item No: Hydro6000X
Size: 120*125*297mm (4¾*5*11¾ in)
Water flow: 3L/min (0.79 G/min)
Working water pressure: 0.07-0.35Mpa (10.15-50.76 PSI)
Working water temperature: 5 to 35°C (41 to 95°F)
Weight: 1.7KGS (3.75 LBS)
Installation type: Quick fitting
Filters: UF membrane & composite filter
Life of the filters: 6000L water flow (varies for different water qualities)
Packaging: One set/color box, 6 sets/carton
Carton size: 510*510*390mm (20*20*15¼in)
A. Water output
B. UF membrane Filter
C. Composite filter
D. Machine housing
E. Base pad
G
H
A
B
C
D
E
F
F. Water output connector toggle
G. Diverter
H. 3 Adapters
Attentions
3
Attentions
Safety Attentions
The feed water of the machine must be higher or equal quality
of municipal tap water.
Please let the output water flow about 15 seconds before using
the purified water.
Please let the output water flow at least 1 minute if you didn’t
use the machine for more than 2 days.
If your local tap water is dirty or you not at home for long time,
please open your tap water for minutes and then open the
machine faucet.
Please replace your UF membrane filter cartridge if you found
the water flow turns very small.
Please use the machine under available feed water pressure
(0.07~0.35 Mpa). Please adjust your feed water pressure if it
is too high, otherwise it will destroy the machine.
The feed water temperature of the machine is 5°C ~ 35°CH.
Please don’t clean the body of the machine with corrosive
liquid or detergent.
Please don’t demount the machine at random.
H.
G.
F.
E.
D.
C.
B.
A.
4
Installation
Other s
Installation of Diverter
1. Dismount the nut
from the faucet.
2. Choose the suitable
adapter.
3. Put the nut mounting
in upward, install the
outer thread adapter
with faucet.
4. Screw down the
connector head into
the connector, then
connect the machine
hose.
5. When install is complete
allow water to run through
the system. Inspect all
connections, and verify no
leaks are present.
Installation
Replacement
5
Replacement of the Battery
Functions Instructions
A. Pull out the back cover of the battery box.
B. Open the cover of the battery box.
C. Remove batteries from the battery jar.
D. Place the new batteries into the battery jar.
E. Put the battery pack back into the machine body.
F. Close the back cover.
A. After installing the battery, the LCD screen will illuminate.
B. It will show 6000 on the screen (it means the life of the UF
membrane filter has 6000L of water flow).
C. The display will turn off if there is no water flow through the
machine.
D. It will turn on again when the water flow is turned on.
E. When the voltage capacity is less than 2.6V, it will show low
voltage on the screen and will disappear after replacing the
battery.
6
Replacement
Replacement of the Filter Cartridges
How to replace the filter cartridges?
Before beginning point water output pipe to halfway down
A. Align the tabs on the water output with the tabs on the housing.
B. Put tab into unlock position.
C. Rotate the water output pipe counter-clockwise.
D. Pull out the filter cartridges.
E. Rotate the water output pipe clockwise.
F. The filter cartridges and the water output pipe are now separated.
G. Now connect the new filter cartridges to the water output pipe.
H. Rotate the water output pipe counter-clockwise.
I. Once secured put the output pipe back into the machine body.
J. Rotate the water output pipe clockwise.
*Push in the snap joint once secure*
Troubleshooting
7
Troubleshooting
The head of the machine
(Leaking)
The head of the Connection
pipe (Leaking)
1. Did not install the faucet
in right way
1. Install again
2. Repair the faucet
Please connect it again
2. The head of the faucet is
broken or damaged.
The seal ring is broken
The head of the pipe is not
connecting well
The main body of the
machine (Leaking)
Please check and connect
again.
The inner connecting pipe
of the machine is slack
Tap water flow turns slowly
or no water
Clean the net of the faucet1. The tap water filter net
was blocked
The purified water flow
turns slowly
1. Check the pipe1. The pipe of the water
output is buckling
The purified water has bad
smell or taste
Replace the filtersThe life of the filter
runs out
If the Pipe is no problem,
replace a new filter
The filter inside is
blocking
The source water outlet
is dirty
Change the seal ring
The seal ring is broken
Problems Reasons Solutions
/
