Krone BA Comprima F 155 XC (RP701-21) Operating instructions

Original operating instructions

Document number: 150001050_06_us

Version: 21/08/2023

RP701-21

Round baler

Comprima F 155 XC

From machine number: 1136331

2

Comprima F 155 XC

Original operating instructions 150001050_06_us

Contact

Krone North America, Inc.

12121 Forest Dr.

Olive Branch, MS 38654

U.S.A.

Phone + 1 662 913-7171

Fax + 1 662 913-7137

Email [email protected]

Internet www.krone-northamerica.com

For information on your KRONE machines, also refer to mykrone.green. After you have

registered, you can generate and manage your machines via the machine number so that you

can view the machine data. Via your personal account, you can also access all KRONE

Services.

Information for enquiries and orders

Model

Vehicle identification number

Year of manufacture

Contact data of your dealer

Table of contents

Comprima F 155 XC

Original operating instructions 150001050_06_us 3

1 Information on This Document.................................................................................................9

1.1 Validity .........................................................................................................................................9

1.2 Significance of the document.......................................................................................................9

1.3 Re-ordering ..................................................................................................................................9

1.4 Applicable documents..................................................................................................................9

1.5 Target group of this document .....................................................................................................9

1.6 How to use this document..........................................................................................................10

1.6.1 Directories and references.........................................................................................................10

1.6.2 Information on direction .............................................................................................................10

1.6.3 Term “machine”..........................................................................................................................10

1.6.4 Figures .......................................................................................................................................10

1.6.5 Scope of the document ..............................................................................................................10

1.6.6 Means of representation ............................................................................................................10

1.6.7 Conversion table ........................................................................................................................13

2 Safety ........................................................................................................................................14

2.1 Intended use ..............................................................................................................................14

2.2 Reasonably foreseeable misuse................................................................................................14

2.3 Service life of the machine.........................................................................................................15

2.4 Basic safety instructions ............................................................................................................15

2.4.1 Importance of operating instructions..........................................................................................15

2.4.2 Personnel qualification of the operating personnel ....................................................................15

2.4.3 Personnel qualification of the technicians..................................................................................16

2.4.4 Children in danger......................................................................................................................16

2.4.5 Connecting the machine ............................................................................................................16

2.4.6 Structural modifications on the machine ....................................................................................16

2.4.7 Additional equipment and spare parts .......................................................................................16

2.4.8 Jobs on the machine..................................................................................................................17

2.4.9 Operational safety: Technically sound condition........................................................................17

2.4.10 Danger zones.............................................................................................................................18

2.4.11 Ensuring functionality of safety devices .....................................................................................20

2.4.12 Personal protective equipment ..................................................................................................20

2.4.13 Safety sign on the machine........................................................................................................21

2.4.14 Road safety................................................................................................................................21

2.4.15 Parking the machine safely .......................................................................................................22

2.4.16 Consumables .............................................................................................................................22

2.4.17 Dangers arising from environment.............................................................................................23

2.4.18 Sources of danger on the machine ............................................................................................24

2.4.19 Dangers in connection with certain activities: Working on the machine ....................................25

2.4.20 Dangers in connection with certain activities: working on wheels and tyres..............................26

2.4.21 Behaviour in dangerous situations and in case of accidents .....................................................27

2.5 Safety routines ...........................................................................................................................27

2.5.1 Shutting down and safeguarding the machine...........................................................................27

2.5.2 Securing raised machine and machine parts against lowering..................................................28

2.5.3 Carrying out oil level check and oil and filter element changes safely.......................................28

2.5.4 Running actuator test.................................................................................................................29

2.6 Safety sign on the machine........................................................................................................29

2.7 Information signs on the machine ..............................................................................................34

2.8 Safety equipment .......................................................................................................................40

2.8.1 SMV emblem .............................................................................................................................41

3 Data memory ............................................................................................................................43

4 Machine description ................................................................................................................44

4.1 Machine overview ......................................................................................................................44

4.2 Overload protections on the machine ........................................................................................44

4.3 Identification plate ......................................................................................................................45

4.4 Scope of delivery .......................................................................................................................46

4.5 Function description net wrapping .............................................................................................47

4.6 Function description of net wrapping and base coat film wrapping ...........................................48

4.7 Function description cutting unit ................................................................................................49

5 Technical data ..........................................................................................................................50

Table of contents

4

Comprima F 155 XC

Original operating instructions 150001050_06_us

5.1 Dimensions ................................................................................................................................50

5.2 Technically permitted maximum speed (road travel) .................................................................50

5.3 Airborne noise emission.............................................................................................................50

5.4 Ambient temperature .................................................................................................................50

5.5 Tyres ..........................................................................................................................................51

5.6 Safety chain ...............................................................................................................................51

5.7 Bale dimensions.........................................................................................................................51

5.8 Net wrapping and tying material ................................................................................................51

5.9 Wrapping material base coat film...............................................................................................52

5.10 Requirements for tractor - power ...............................................................................................52

5.11 Tractor requirements – hydraulics .............................................................................................52

5.12 Requirements for tractor – electrics ...........................................................................................52

5.13 Requirements for tractor – brake system...................................................................................52

5.14 Consumables .............................................................................................................................53

5.14.1 Oils.............................................................................................................................................53

5.14.2 Lubricating greases....................................................................................................................53

6 Initial operation ........................................................................................................................54

6.1 Checklist for initial operation ......................................................................................................54

6.2 Scope of delivery .......................................................................................................................55

6.3 Mounting hose and cable support..............................................................................................55

6.4 Preparing the brake disc of the wrapping material brake...........................................................56

6.5 Adjusting the drawbar height .....................................................................................................56

6.6 Universal shaft ...........................................................................................................................58

6.6.1 Mounting protective cap of universal shaft.................................................................................58

6.6.2 Mounting the universal shaft on the machine ............................................................................58

6.6.3 Adjusting the length of the universal shaft .................................................................................59

6.6.4 Mounting universal shaft bracket ...............................................................................................60

6.7 Removing the tensioning device ................................................................................................60

7 Commissioning ........................................................................................................................62

7.1 Connecting machine to tractor ...................................................................................................62

7.2 Mounting the universal shaft on the tractor................................................................................63

7.3 Connecting hydraulic hoses.......................................................................................................64

7.4 Connecting hydraulic brake (export) ..........................................................................................65

7.5 Connecting/disconnecting compressed air connections for the compressed air brake .............65

7.6 Connecting the road lighting ......................................................................................................66

7.7 Mounting safety chain ................................................................................................................67

7.8 Mounting the catch loop.............................................................................................................68

7.9 Connecting the KRONE DS 100 operation unit .........................................................................69

7.10 Connecting KRONE terminal DS 500 ........................................................................................70

7.11 Connecting the KRONE ISOBUS terminal (CCI800, CCI 1200)...............................................72

7.12 Connecting foreign ISOBUS terminal ........................................................................................74

7.13 Connecting joystick ....................................................................................................................75

7.14 Connecting the camera to the KRONE ISOBUS terminal CCI 800 or CCI 1200 .......................78

8 Operation ..................................................................................................................................79

8.1 Preparation before baling...........................................................................................................79

8.2 Filling the bale chamber.............................................................................................................80

8.3 Improving bale chamber filling ...................................................................................................82

8.3.1 Reducing the pressure on the side walls of the bale chamber ..................................................82

8.3.2 Mounting additional deflector sheets in the tailgate ...................................................................82

8.3.3 Mounting additional driver guide rails on the starter roller .........................................................82

8.4 Completing the baling process, starting tying cycle and ejecting round bales...........................83

8.5 Operating the support jack.........................................................................................................83

8.6 Using the stop cock of the tailgate .............................................................................................85

8.7 Using stop cock of the blade press-in device.............................................................................86

8.8 Releasing/applying the parking brake........................................................................................87

8.9 Fitting wheel chocks...................................................................................................................88

8.10 Removing/mounting the safety device which prevents unauthorised use .................................88

8.11 Operating brake force regulator .................................................................................................89

8.12 Pick-up .......................................................................................................................................90

Table of contents

Comprima F 155 XC

Original operating instructions 150001050_06_us 5

8.12.1 Bringing the pick-up to transport/working position .....................................................................90

8.12.2 Setting the pick-up working height .............................................................................................91

8.12.3 Adjusting the bearing pressure relief for the pick-up..................................................................92

8.13 Crop press roller unit..................................................................................................................92

8.13.1 Setting the crop press roller unit ................................................................................................93

8.13.2 Setting the baffle sheet on the crop press roller unit..................................................................93

8.13.3 Removing/mounting the baffle sheet on the crop press roller unit.............................................94

8.14 Cutting unit.................................................................................................................................95

8.14.1 Lifting/lowering blade cassette...................................................................................................95

8.14.2 Swivelling blade groups in/out ...................................................................................................96

8.14.3 Briefly deactivating the cutting unit ............................................................................................99

8.15 Net wrapping..............................................................................................................................99

8.15.1 Inserting the net roll ...................................................................................................................99

8.15.2 Insert net ..................................................................................................................................101

8.16 Net wrapping and base coat film wrapping ..............................................................................102

8.16.1 Inserting a net or film roll..........................................................................................................102

8.16.2 Inserting net or base coat film..................................................................................................103

8.16.3 Notes on operation...................................................................................................................106

8.16.4 Check tension of the inserted base coat film ...........................................................................107

8.17 Using the bale ejector ..............................................................................................................108

8.18 Removing crop blockages........................................................................................................108

8.18.1 Crop blockage at the right-hand and left-hand end of the pick-up ...........................................108

8.18.2 Crop blockage under the cutting rotor......................................................................................109

8.18.3 Crop blockage in the baling element........................................................................................110

8.19 Operating the central chain lubrication system ........................................................................110

9 KRONE operation unit DS 100 ..............................................................................................112

9.1 Overview ..................................................................................................................................112

9.2 Switching the operation unit on/off...........................................................................................114

9.3 Call road travel screen .............................................................................................................114

9.4 Accessing the working screen .................................................................................................115

9.5 Direction display.......................................................................................................................115

9.6 Start tying.................................................................................................................................116

9.7 Switching the working lights on/off...........................................................................................117

9.8 Switching warning beacon on/off .............................................................................................117

9.9 Setting the bale diameter .........................................................................................................117

9.10 Setting advance signaling ........................................................................................................118

9.11 Setting the sensitivity of the direction display ..........................................................................119

9.12 Setting the baling pressure ......................................................................................................119

9.13 Setting the number of net layers ..............................................................................................120

9.14 Setting the tying start delay......................................................................................................121

9.15 Displaying the customer counter..............................................................................................122

9.16 Sensor test for digital and analogue sensors...........................................................................123

9.17 Calibrating sensors ..................................................................................................................124

9.18 Actuator test for digital and analogue actuators.......................................................................126

9.19 Error messages........................................................................................................................128

9.20 Manual operation of the tying system ......................................................................................129

9.21 Setting user preferences..........................................................................................................130

10 KRONE Terminal DS 500 .......................................................................................................131

10.1 Touchable display ....................................................................................................................131

10.2 Switching terminal on/off..........................................................................................................131

10.3 Design DS 500.........................................................................................................................132

11 KRONE ISOBUS terminal (CCI 800, CCI1200) ....................................................................134

11.1 Touchable display ....................................................................................................................134

11.2 Switching terminal on/off..........................................................................................................135

11.3 Design of display......................................................................................................................136

11.4 Design of the KRONE machine application .............................................................................136

11.5 Setting units on the terminal ....................................................................................................137

12 Foreign ISOBUS terminal ......................................................................................................138

Table of contents

6

Comprima F 155 XC

Original operating instructions 150001050_06_us

12.1 Varying functions to KRONE ISOBUS terminal .......................................................................138

13 Terminal machine functions .................................................................................................139

13.1 Status line ................................................................................................................................139

13.2 Keys .........................................................................................................................................140

13.3 Displays on the working screen ...............................................................................................142

13.4 Displays on the information bar ...............................................................................................145

13.5 Direction display.......................................................................................................................145

13.6 ISOBUS Shortcut Button (ISB) ................................................................................................147

13.7 Accessing the working screen .................................................................................................148

13.8 Automatic call of the Road travel screen .................................................................................149

13.9 Adjusting the baling pressure...................................................................................................149

13.10 Operating the hydraulic blade group control system................................................................150

13.11 Operating TIM 1.0 (Tractor Implement Management) .............................................................152

13.11.1 Mode of operation of TIM 1.0...................................................................................................152

13.11.2 TIM displays and keys on the working screen .........................................................................152

13.11.3 Activating TIM functions...........................................................................................................153

13.11.4 Pausing TIM functions .............................................................................................................154

13.12 Operating machine via joystick ................................................................................................155

13.12.1 Auxiliary functions (AUX) .........................................................................................................155

13.12.2 Auxiliary assignment of a joystick ............................................................................................155

14 Terminal menus .....................................................................................................................158

14.1 Menu Structure ........................................................................................................................158

14.2 Recurrent icons........................................................................................................................159

14.3 Selecting a menu Level............................................................................................................160

14.4 Selecting a menu .....................................................................................................................160

14.5 Changing value ........................................................................................................................161

14.6 Changing mode........................................................................................................................162

14.7 Tying in the menu level ............................................................................................................163

14.8 Menu 1 "Number of tying material layers"................................................................................ 164

14.9 Menu 3 “Advance signalling”....................................................................................................164

14.10 Menu 4 "Tying start delay" ....................................................................................................... 165

14.11 Menu 5 “Bale diameter” ...........................................................................................................165

14.12 Menu7 “Sensitivity of direction display”...................................................................................166

14.13 Menu 8 "Selection of tying method (for "net wrapping and base coat film wrapping" version) 167

14.14 Menu 10 "Manual operation" (for "Net wrapping" version)....................................................... 168

14.15 Menu 10 "Manual operation (for "net wrapping and base coat film wrapping" version)...........169

14.16 Menu 12 "Moisture measurement"........................................................................................... 170

14.16.1 Menu 12-1 "Error message for moisture measurement".......................................................... 171

14.16.2 Menu 12-2 "Correction value for moisture measurement" ....................................................... 172

14.17 Menu 21 "Gathering unit (for "net wrapping and base coat film wrapping" version) ................173

14.18 Menu 13 "Counters" .................................................................................................................174

14.18.1 Menu 13-1 “Customer counter”................................................................................................174

14.18.2 Menu 13-2 "Total counter" ....................................................................................................... 176

14.19 Menu 14 "ISOBUS" ..................................................................................................................177

14.19.1 Menu 14-5 "KRONE SmartConnect"........................................................................................178

14.19.2 Menu 14-6 "Configuring TIM software" (for "TIM 1.0" version) ................................................179

14.19.3 Menu 14-9 "Switching between terminals"............................................................................... 180

14.20 Menu 15 "Settings"...................................................................................................................181

14.20.1 Menu 15-1 "Sensor test" .......................................................................................................... 182

14.20.1.1 Adjusting sensor B08 “Top blade cassette” .............................................................................184

14.20.1.2 Adjusting sensor B09/B10 “Filling display left/right”.................................................................185

14.20.1.3 Adjusting sensor B61 “Tying 1 (passive)” ................................................................................186

14.20.2 Menu 15-2 "Actuator test" ........................................................................................................ 186

14.20.3 Menu 15-3 "Software info" ....................................................................................................... 189

14.20.4 Menu 15-4 "Error list" ...............................................................................................................190

15 Driving and transport ............................................................................................................192

15.1 Preparing the machine for road travel......................................................................................193

15.2 Parking the machine ................................................................................................................193

15.3 Securing the universal shaft.....................................................................................................194

Table of contents

Comprima F 155 XC

Original operating instructions 150001050_06_us 7

15.4 Checking road travel lighting....................................................................................................195

15.5 Dismounting the guide wheels of the pick-up for road travel ...................................................195

15.6 Preparing the machine for shipment ........................................................................................196

15.6.1 Checklist for the transport of the machine ...............................................................................197

15.6.2 Securing the side hoods ..........................................................................................................197

15.6.3 Securing the storage compartment flap ...................................................................................197

15.6.4 Mounting the tensioning device ...............................................................................................198

15.6.5 Lifting the machine...................................................................................................................198

15.6.6 Lashing the machine................................................................................................................199

16 Settings...................................................................................................................................201

16.1 Setting the baling pressure ......................................................................................................201

16.2 Setting the bale diameter .........................................................................................................201

16.3 Setting the cutting length .........................................................................................................202

16.4 Checking and setting the position of the feed rocker arm........................................................202

16.4.1 Checking and adjusting the feed position ................................................................................203

16.4.2 Checking and setting end position for base coat film wrapping ...............................................204

16.4.3 Checking and setting end position for net wrapping ................................................................205

16.5 Setting wrapping material overhang ........................................................................................206

16.6 Setting wrapping material brake ..............................................................................................207

16.7 Setting the brake force release when feeding wrapping material ............................................208

16.8 Checking and setting the axial play of the brake disc at the wrapping material brake.............209

16.9 Locking/releasing the tension lever..........................................................................................210

16.10 Setting the lock of the tapered roller ........................................................................................211

16.11 Checking the retaining comb for net wrapping.........................................................................212

16.12 Checking retaining comb for base coat film wrapping .............................................................213

16.13 Setting the working lights .........................................................................................................213

17 Maintenance ...........................................................................................................................215

17.1 Observe the service record booklet .........................................................................................215

17.2 Maintenance table....................................................................................................................215

17.2.1 Maintenance – Before the season ...........................................................................................215

17.2.2 Maintenance – After the season ..............................................................................................216

17.2.3 Maintenance – once after 10 hours .........................................................................................217

17.2.4 Maintenance – once after 50 hours .........................................................................................217

17.2.5 Maintenance – Once after 500 round bales.............................................................................217

17.2.6 Maintenance – every 10 hours, at least daily...........................................................................217

17.2.7 Maintenance – every 50 hours.................................................................................................218

17.2.8 Maintenance – Every 500 hours ..............................................................................................218

17.2.9 Maintenance – Every 2 years ..................................................................................................218

17.3 Lubrication chart ......................................................................................................................218

17.4 Lubricating the universal shaft .................................................................................................222

17.5 Tightening torques ...................................................................................................................222

17.6 Checking/maintaining tyres......................................................................................................226

17.7 Servicing the main gearbox .....................................................................................................227

17.8 Cleaning the machine ..............................................................................................................228

17.9 Cleaning deflection pipes or conical tying roller.......................................................................228

17.10 Clean the bushing and the drawbar eye ..................................................................................230

17.11 Cleaning drive chains...............................................................................................................231

17.12 Protecting brake disc of the wrapping material brake from corrosion ......................................231

17.13 Checking the screw connections on the drawbar ....................................................................231

17.14 Setting the scraper and stone deflector ...................................................................................232

17.14.1 Adjusting the scraper in relation to the lower compression roller.............................................232

17.14.2 Checking scraper wedge on the scraper of the lower compression roller ...............................233

17.14.3 Adjusting the scraper on the deflection shafts .........................................................................233

17.14.4 Adjusting the scraper on the fixed deflection rolls....................................................................234

17.15 Releasing the cam clutch on the universal shaft......................................................................235

17.16 Changing the blades ................................................................................................................235

17.17 Unlocking/locking blade retaining shaft....................................................................................236

17.18 Checking and moving the blade retaining shaft .......................................................................237

17.19 Grinding the blades..................................................................................................................238

17.20 Checking/lubricating the safety rolls of the single blade locking device...................................239

Table of contents

8

Comprima F 155 XC

Original operating instructions 150001050_06_us

17.21 Adjust drive chains...................................................................................................................240

17.21.1 Drive chain of the pick-up ........................................................................................................240

17.21.2 Drive chain of the intake ..........................................................................................................241

17.21.3 Drive chain of the bale formation conveyor..............................................................................242

17.21.4 Drive chain of the auger conveyor ...........................................................................................243

17.21.5 Drive chain of the starter roller and the lower compression roller............................................243

17.21.6 Drive chain of the gathering unit ..............................................................................................244

17.22 Checking the bale formation conveyor tension ........................................................................244

17.23 Servicing chain lubrication unit ................................................................................................244

17.23.1 Checking oil level, topping up oil and changing filter ...............................................................245

17.23.2 Position of the oil brushes........................................................................................................247

17.23.3 Position of the dosing units ......................................................................................................248

17.23.4 Cleaning the dosing units.........................................................................................................249

17.23.5 Replacing the hose on the dosing unit.....................................................................................250

17.24 Servicing compressed air brake (for version with "Compressed air brake") ............................ 251

17.24.1 Cleaning air filter ......................................................................................................................251

17.24.2 Drain condensation water from the compressed air tank.........................................................252

17.24.3 Retighten tensioning straps at the compressed air tank ..........................................................253

17.25 Servicing the hydraulic system ................................................................................................253

17.25.1 Checking hydraulic hoses ........................................................................................................254

17.25.2 Solenoid valves........................................................................................................................254

18 Malfunction, cause and remedy ...........................................................................................255

18.1 Disturbances at the pick-up or during picking up of crops .......................................................255

18.2 Disturbances during or after the baling process ......................................................................256

18.3 Disturbances at the tying unit or during the tying cycle............................................................258

18.4 Disturbances on the blade cassette.........................................................................................261

18.5 Malfunctions on the chain lubrication unit ................................................................................261

18.6 Faults of the electrics/electronics.............................................................................................262

18.6.1 Error Messages........................................................................................................................262

18.6.1.1 Possible error types (FMI)........................................................................................................263

18.6.2 Overview of fuses ....................................................................................................................264

18.6.3 Remedying sensor/actuator error ............................................................................................264

18.7 Setting the tailgate lock............................................................................................................265

18.8 Car jack contact points.............................................................................................................265

19 Waste disposal.......................................................................................................................267

20 Index........................................................................................................................................268

Information on This Document 1

Validity 1.1

Comprima F 155 XC

Original operating instructions 150001050_06_us 9

1 Information on This Document

1.1 Validity

This document is valid for machines of type:

RP701-21 (Comprima F 155 XC)

All information, illustrations and technical data in this document correspond to the latest state at

the time of publication.

We reserve the right to make design changes at any time and without notification of reasons.

1.2 Significance of the document

This is an important document. It is addressed to the user and contains safety-relevant

information.

Prior to starting work, read the complete document and observe its contents.

Keep this document ready to hand in the document storage tube for the user of the

machine, see Page44.

Hand over this document to subsequent users.

1.3 Re-ordering

You can request a replacement document if this document became completely or partly

unusable, or if you need it in a different language. Please specify the document number shown

on the cover page in your order. Alternatively, you can download the document online from

KRONE MEDIA https://media.mykrone.green.

1.4 Applicable documents

To ensure that the machine is used safely and as intended, observe the following further

applicable documents.

• Operating instructions for universal shaft

• Operating instructions for operation unit/terminal

• Operating instructions for camera system (for "net wrapping and base coat film wrapping"

version)

• AUX joystick operating instructions

• Supplement to operating instructions "Error messages"

• Circuit diagram, KRONE

• Spare parts list, KRONE

• Service record booklet, KRONE

1.5 Target group of this document

This document aims at the operator of the machine who fulfills the minimum requirements of

personnel qualification,see Page15.

1 Information on This Document

1.6 How to use this document

10

Comprima F 155 XC

Original operating instructions 150001050_06_us

1.6 How to use this document

1.6.1 Directories and references

Contents/headers

The contents and headers in this document ensure quick orientation in the chapters.

Index

The index contains catchwords in alphabetical order which enable to find information on a

desired topic easily. The index can be found on the last pages of this document.

Cross references

Cross references to another place in the document or to another document are in the text with

page number.

Examples:

• Check the tight seat of all screws on the machine, see Page10. (INFO: If you use an

electronic version of this document, click on the link to go to the specified page.)

• For further information, refer to the operating instructions of the universal shaft

manufacturer.

1.6.2 Information on direction

Directional information in this document, such as front, rear, right and left, applies in the

direction of travel of the machine.

1.6.3 Term “machine”

Throughout the rest of this document, the “round baler” will also be referred to as the “machine”.

1.6.4 Figures

The figures in this document do not always represent the exact machine type. The information

that refers to the figure always corresponds to the machine type of this document.

1.6.5 Scope of the document

In addition to standard equipment, accessories kits and versions of the machine are described

in this document. Your machine may deviate from this document.

1.6.6 Means of representation

Icons in the text

The following means of representation (icons) are used to present the text more clearly:

Information on This Document 1

How to use this document 1.6

Comprima F 155 XC

Original operating instructions 150001050_06_us 11

This arrow characterizes an action step. Several arrows in a row identify a sequence of

actions to be performed step by step.

This icon identifies a prerequisite that has to be fulfilled to perform an action step or a

sequence of actions.

This arrow marks the intermediate result of an action step.

This arrow identifies the result of an action step or sequence of actions.

This bullet point identifies an enumeration. If the bullet point is intended, it identifies the

second level of the enumeration.

Icons in figures

The following icons can be used in illustrations:

Icon Explanation Icon Explanation

1

Reference sign for part

I

Position of a part (e.g. move from

position I to position II)

X

Dimensions (e. g. also W = width,

H = height, L = length)

Magnification of display detail

LH

Left side of machine

RH

Right side of machine

Direction of travel Direction of motion

Reference line for visible material Reference line for covered mater-

ial

Centre line Cable routes

Open Closed

Apply liquid lubricant (e.g. lubric-

ating oil)

Apply lubricating grease

Warning signs

Warnings of dangers are separated from the remaining text as warning signs and are identified

with a danger sign and signal words.

The warning signs must be read and the measures must be observed in order to prevent

personal injury.

Explanation of danger sign

This is the danger sign that warns of a risk of injury.

Please observe all notes marked with the danger sign in order to avoid injuries or death.

1 Information on This Document

1.6 How to use this document

12

Comprima F 155 XC

Original operating instructions 150001050_06_us

Explanation of signal words

DANGER

The signal word DANGER warns of a hazardous situation which will result in serious injuries

or death if the warning sign is ignored.

WARNING

The signal word WARNING warns of a hazardous situation which will result in serious injuries

or death if the warning sign is ignored.

CAUTION

The signal word CAUTION warns of a hazardous situation which will result in minor to

moderate injuries if the warning sign is ignored.

Example of a warning sign:

WARNING

Eye damage caused by flying dirt particles

When cleaning with compressed air, dirt particles are ejected at high speed and could get into

the eyes. Therefore eyes could be hurt.

Keep people away from the working area.

Wear personal protective equipment when performing cleaning work with compressed air

(e.g. eye protection).

Warnings of property damage/environmental damage

Warnings of property/environmental damage are separated from the remaining text and marked

with "Notice".

Example:

NOTICE

Gearbox damage due to low oil level

The gearboxes could be damaged when the oil level is too low.

Check gear oil level at regular intervals and top up oil, if necessary.

Check gear oil level approx. 3 to 4 hours after the machine has been switched off. Check

oil level only when machine is in horizontal position.

Notices with information and recommendations

Additional information and recommendations for trouble-free and productive operation of the

machine are separated from the remaining text and marked with “Information”.

Example:

INFO

Each safety sign is provided with an order number and can be ordered directly from the

manufacturer or from an authorised specialist dealer.

Information on This Document 1

How to use this document 1.6

Comprima F 155 XC

Original operating instructions 150001050_06_us 13

1.6.7 Conversion table

The following table can be used to convert metric units into US units.

Size SI units (metric) Factor Inch-pound units

Unit name Abbrevi-

ation

Unit name Abbrevi-

ation

Area Hectare ha 2.47105 Acre acres

Volume flow Litres per minute L/min 0.2642 US gallons per

minute

gpm

Cubic metres

per hour

m³/h 4.4029

Force Newton N 0.2248 Pound force lbf

Length Millimetre mm 0.03937 Inch in.

Metre m 3.2808 Foot ft.

Power Kilowatt kW 1.3410 Horsepower hp

Pressure Kilopascal kPa 0.1450 Pounds per

square inch

psi

Megapascal MPa 145.0377

bar (non-SI) bar 14.5038

Torque Newtonmeter Nm 0.7376 pound-foot or

foot-pound

ft∙lbf

8.8507 pound-inch or

inch-pound

in∙lbf

Temperature Degrees Celsius °C °Cx1.8+32 Degrees

Fahrenheit

°F

Velocity Metres per

minute

m/min 3.2808 Feet per minute ft/min

Metres per

second

m/s 3.2808 Feet per second ft/s

Kilometres per

hour

km/h 0.6215 Miles per hour mph

Volumes Litres L 0.2642 US gallon US gal.

Millilitre ml 0.0338 US ounce US oz.

Cubic centi-

metre

cm³ 0.0610 Cubic inch in³

Weight Kilogram kg 2.2046 Pound lbs

2 Safety

2.1 Intended use

14

Comprima F 155 XC

Original operating instructions 150001050_06_us

2 Safety

2.1 Intended use

This machine is a round baler and is used to press crops to round bales.

The crops designated for the intended use of this machine are cut stalk and leaf crops.

The machine is designed exclusively for use in agriculture and may only be used when

• all safety devices are available according to the operating instructions and are located in the

protective position.

• all safety instructions of the operating instructions have been observed and complied with,

both in chapter “Basic safety instructions”, see Page15, and directly in the chapters of the

operating instructions.

The machine may be used only by people who satisfy the personnel qualification requirements

designated by the machine manufacturer, see Page15.

These operating instructions are part of the machine and must therefore be at hand when the

machine is in use. The machine may be operated only when the operator has received training

and in compliance with these operating instructions.

If the machine is used for applications which are not described in these operating instructions,

this may result in serious injuries or death and damage to the machine and other property.

Unauthorised modifications to the machine may affect the properties of the machine or disrupt

the proper operation. For this reason, unauthorised modifications shall exclude any liability of

the manufacturer for consequential damage.

The intended use shall also include the adherence to the operating, maintenance and repair

conditions set by the manufacturer.

2.2 Reasonably foreseeable misuse

Any use beyond the intended usesee Page14 is regarded as improper use and is therefore

misuse according to the Machinery Directive. The manufacturer is not liable for damage

resulting from this, the user alone bears the risk.

Such misuse is for example:

• Processing of crops which are outside the intended use of the machine,see Page14

• Transport of people

• Transport of goods

• Exceeding the permitted technical gross weight

• Non-compliance with the safety labels on the machine and safety notes in the operating

instructions

• Performing troubleshooting, setting, cleaning, repair and maintenance work contrary to the

information in the operating instructions

• Unauthorised modifications to the machine

• Attachment of unauthorised or unapproved additional equipment

• Use of spare parts which are not KRONE original spare parts

• Stationary operation of the machine

Unauthorised modifications to the machine may affect the properties of the machine or disrupt

proper operation. For this reason, unauthorised modifications will exclude any liability of the

manufacturer for consequential damage.

Safety 2

Service life of the machine 2.3

Comprima F 155 XC

Original operating instructions 150001050_06_us 15

2.3 Service life of the machine

• The service life of this machine depends on its proper operation and maintenance as well

as the operating and harvesting conditions.

• By heeding the instructions and information in these operating instructions, permanent

operational readiness and a long service life of the machine can be achieved.

• After each operating season, inspect the entire machine for wear and other damage.

• Replace damaged and worn components before recommissioning the machine.

• Carry out a full technical inspection of the machine after five years of machine operation

and make a decision on further machine usage taking the results of this inspection into

account.

• Theoretically, the service life of this machine is unlimited as all worn or damaged

components can be replaced.

2.4 Basic safety instructions

Non-compliance with the safety instructions and warnings

Non-compliance with the safety instructions and warnings may result in injuries and damage to

the environment and property.

2.4.1 Importance of operating instructions

The operating instructions are an important document and a part of the machine. They are

intended for the user and contain information that is relevant to safety.

Only the procedures specified in the operating instructions are safe. If the operating instructions

are not followed, there is a risk of serious or even fatal injuries.

Prior to using the machine for the first time, read and observe the "Basic safety notices"

completely.

Prior to starting work, read and observe the respective sections in the operating instructions

too.

Keep the operating instructions ready to hand for the user of the machine in the document

storage tube, see Page44.

Hand over the operating instructions to subsequent users.

2.4.2 Personnel qualification of the operating personnel

If the machine is not used properly, people may be seriously injured or killed. To avoid

accidents, each person who works with the machine must satisfy the following minimum

requirements:

• He is physically capable of controlling the machine.

• He can work safely with the machine in accordance with these operating instructions.

• He understands the method of operation of the machine within the scope of his work and

can identify and avoid the dangers associated with the work.

• He has read the operating instructions and can implement the information in the operating

instructions accordingly.

• He is familiar with driving vehicles safely.

• For road travel he has adequate knowledge of the highway code and has the stipulated

driving licence.

2 Safety

2.4 Basic safety instructions

16

Comprima F 155 XC

Original operating instructions 150001050_06_us

2.4.3 Personnel qualification of the technicians

If the work (assembly, conversion, modification, extension, repairs, retrofitting) is performed

improperly on the machine, people may be seriously or fatally injured. To avoid accidents,

everyone who performs work according to these instructions must meet the following minimum

requirements:

• Qualified professional, with relevant training.

• Capable of assembling the (partially) disassembled machine according to the assembly

instructions provided by the manufacturer.

• He is capable, e.g. by attending a training course, of extending, modifying or repairing the

function of the machine according to the relevant instructions provided by the manufacturer.

• He has read the operating instructions and can implement the information in the operating

instructions accordingly.

• Ability to perform the work safely according to these instructions.

• Understands the mode of operation of the work to be performed and the machine and is

able to identify and avoid risk in carrying out the necessary work.

• Has read these instructions and is able to implement the information explained in these

instructions accordingly.

2.4.4 Children in danger

Children are not in a position to assess dangers and behave unpredictably.

Thus children are particularly at risk.

Keep children away from the machine.

Keep children away from consumables.

Make sure that there are no children in the danger zone, especially when starting and

triggering machine movements.

2.4.5 Connecting the machine

When tractor and machine are not correctly connected, there is a risk of causing serious

accidents.

When connecting, follow all operating instructions:

• the operating instructions of the tractor

• the operating instructions of the machine, see Page62

• the operating instructions of universal shaft

Observe the changed driving behaviour of the combination.

2.4.6 Structural modifications on the machine

Structural modifications and extensions that were not approved by KRONE can impair the

functionality, operational safety and also the road traffic certification of the machine. As a result,

persons can be seriously injured or killed.

Any structural modifications and extensions that are not authorised by KRONE are not

permitted.

2.4.7 Additional equipment and spare parts

Additional equipment and spare parts that do not correspond to the requirements of the

manufacturer may affect the operational safety of the machine and cause accidents.

To ensure operational safety, use original parts or standard parts which correspond to the

requirements of the manufacturer.

Safety 2

Basic safety instructions 2.4

Comprima F 155 XC

Original operating instructions 150001050_06_us 17

2.4.8 Jobs on the machine

Passengers

Passengers may be seriously injured by the machine or fall off the machine and run over.

Ejected objects may strike and injure passengers.

Never carry passengers on the machine.

2.4.9 Operational safety: Technically sound condition

Operation only after proper commissioning

The operational safety of the machine is not guaranteed without proper commissioning in

accordance with these operating instructions. This may result in accidents and people may be

seriously or fatally injured.

Use the machine only after proper commissioning, see Page62.

Technically sound state of the machine

Improper maintenance and setting could influence the operational safety of the machine and

cause accidents. Thus there is a risk of serious injuries or death.

All maintenance and setting work must be performed according to the chapters

“Maintenance and Setting”.

Before performing any maintenance and setting work, shut down and safeguard the

machine, see Page27.

Danger resulting from damage to the machine

Damage to the machine may impair the operational safety of the machine and cause accidents.

As a result, people may be seriously injured or killed. The following parts of the machine are

particularly important for safety:

• Brakes

• Steering

• Safety Devices

• Connecting devices

• Lighting

• Hydraulics

• Tyres

• Universal shaft

If there are doubts about the operational safety of the machine, for example due to an

unexpected change to the operational behaviour, visible damage or leaking consumables:

Shut down and safeguard the machine, see Page27.

Immediately eliminate potential causes of damage, for example heavy soiling, or tighten

slack screws.

Determine the cause of damage according to these operating instructions and repair the

damage, if possible, see Page255.

In case of damage which may affect operational safety and cannot be repaired according to

these operating instructions: Have damage repaired by a qualified service centre.

2 Safety

2.4 Basic safety instructions

18

Comprima F 155 XC

Original operating instructions 150001050_06_us

Technical limit values

If the technical limit values of the machine are not observed, the machine may be damaged. As

a result, accidents may occur and people may be seriously or fatally injured. With regard to

safety, it is especially important to observe the following technical limit values:

• maximum permitted operating pressure of the hydraulics

• maximum permitted drive speed

• maximum permitted total weight

• maximum permitted axle load/axle loads

• maximum permitted drawbar load

• maximum permitted axle loads of the tractor

• maximum permitted transport height and width

• maximum permitted speed

Comply with limit values, see Page50.

2.4.10 Danger zones

If the machine is switched on, its surrounding can present a danger zone.

Avoid entering the danger zone of the machine by observing the minimum safety distance.

If the safety distance is not observed, people may be seriously injured or killed.

Do not switch on the drives and engine if the minimum safety distance has not been

observed.

If people fail to observe the minimum safety distance, switch off the drives.

Switch the machine off in shunting and field mode.

The safety distance is:

For machine in shunting and field mode

In front of the machine 3 m

Behind the machine 5 m

On either side of the machine 3 m

For machine switched on without driving motion

In front of the machine 3 m

Behind the machine 5 m

On either side of the machine 3 m

The safety distances specified here are minimum distances in terms of intended use. If

necessary, these safety distances must be increased according to the operating and ambient

conditions.

Before working in front of and behind the tractor and in the danger zone of the machine:

Shut down and secure the machine, see Page27. This also applies to brief inspection

work.

Consider the information in all relevant operating instructions:

• the operating instructions for the tractor

• the operating instructions of the machine

• the operating instructions of universal shaft

Safety 2

Basic safety instructions 2.4

Comprima F 155 XC

Original operating instructions 150001050_06_us 19

Danger zone universal shaft

People may be caught, pulled in and seriously injured by the universal shaft.

Observe operating instructions of universal shaft.

Ensure sufficient overlap of section tube and universal shaft guards.

Make sure that the universal shaft guards are mounted and that they are fully functional.

Allow the universal shaft locks to engage. There must be no areas of the locking device on

the PTO shaft fork which could cause catching or entrapment (e.g. by annular design,

protective collar around the locking pin).

Attach chains to prevent the universal shaft guards from rotating with the shaft.

Make sure that there is no one in the danger zone of PTO shaft and universal shaft.

Ensure that the selected speed and direction of rotation of the PTO shaft of the tractor

match the permitted speed and direction of rotation of the machine.

Switch off the PTO shaft when the angles between the universal shaft and the PTO shaft

are too large. The machine may be damaged. Parts may be hurled up and cause injury to

people.

Danger zone PTO shaft

People may be caught, pulled in and seriously injured by the PTO shaft and the driven

components.

Before switching on the PTO shaft:

Ensure that all protective devices are mounted and brought into protective position.

Make sure that there is no one in the danger zone of PTO shaft and universal shaft.

Switch off drives if they are not needed.

Danger zone between tractor and machine

People standing between the tractor and machine may be seriously injured or killed if the tractor

rolls away or by carelessness or machine movements:

Before carrying out any work between the tractor and the machine: Always turn off and

secure the machine, see Page27. This also applies to brief inspection work.

If the lifting device must be actuated, instruct all people to keep away from the range of

movement of the lifting device.

Danger zone when drive is switched on

When the drive is switched on, there is a danger to life caused by rotating machine parts.

Ensure that there are no persons in the danger zone of the machine.

Before starting the machine, instruct all people to leave the danger zone of the machine.

In case of dangerous situations, immediately switch off drives and instruct people to leave

the danger zone.

Danger zone due to trailing machine parts

If machine parts are trailing, people may be seriously injured or killed.

2 Safety

2.4 Basic safety instructions

20

Comprima F 155 XC

Original operating instructions 150001050_06_us

After the drives have been switched off, the following machine parts will trail:

• universal shaft

• Drive chains

• Pick-up

• Cutting rotor

• Tying unit

• bale formation conveyor

Shut down and safeguard the machine, see Page27.

Do not attempt to approach the machine until all moving machine parts have come to a

standstill.

2.4.11 Ensuring functionality of safety devices

If safety devices are missing or damaged, people may be seriously injured or killed by moving

machine parts.

Replace damaged safety devices.

Mount dismounted safety devices and machine parts again before start-up and move them

to protective position.

If it is doubtful whether all safety devices have been correctly installed and are functional,

have a service centre check them.

Keeping universal shaft guard functional

The overlap of universal shaft and protective cap on the machine must not be less than 50mm.

This minimum overlap is also required for protective devices of wide-angle universal shaft and if

couplings or other components are used. If the operator has to reach between the universal

shaft guard and the protective cap to connect the universal shaft, the clearance on one level

must be at least 50mm. On all levels the clearance must be no more than 150mm.

2.4.12 Personal protective equipment

The wearing of personal protective equipment is an important safety measure. Missing or

unsuitable personal protective equipment increases health risks and injuries.

Personal protective equipment includes, for example:

• Suitable protective gloves

• Safety shoes

• Tight-fitting protective clothing

• Hearing protection

• Protective goggles

• If dust is generated: appropriate breathing protection

Specify and provide personal protective equipment for the particular job.

Use only personal protective equipment which is in proper condition and offers effective

protection.

Adjust personal protective equipment to the person, for example the size.

Remove unsuitable clothing and jewellery (e.g. rings, necklaces) and cover long hair with a

hairnet.

Page is loading ...

Krone BA Comprima F 155 XC (RP701-21) Operating instructions

Related papers

Other documents