About this manual
This bracket is designed for ceiling mounting installation.
Before installing and using this unit, please read this manual carefully.
Be sure to keep it handy for later reference.
CAUTION:
Install this bracket securely according to this
installation manual. Be aware that allowing the
bracket to fall with the camera on it may cause
personal injury.
bSpecifications
Color: Beige
Material: Metal
Waterproof Standard: Conforming to IP66
Weight: Approx. 750 g (1.7 lb)
Allowable Load: Max. 20 kg (44.1 lb)
Dimensions:
Example of
indoor use
Example of
outdoor use
☞P1 ☞P2
Important
• Be careful when opening holes for installing the
unit. Work with the power and video cables pulled
out for easy installation.
• Make sure to properly perform waterproofing for the
wall where you are installing the unit.
• Make sure that the surface in the installation
location has no unevenness and is strong enough
to bear the total weight of the unit.
• Install this unit in an environment where the
temperature range stays between -30°C and +50°C
(-22°F and +122°F) (no condensation allowed).
Ǿ97 (3.8)
75 (3.0)
105 (4.1)
240 (9.4)
192 (7.6)
161 (6.3)
56 (2.2)
17(0.7)
191 (7.5)
4-Ǿ10.8 (0.4)
Unit: mm (inch)
INSTRUCTION MANUAL
Wall Mounting Bracket
VA-80BW
Features and specifications are subject to change without
prior notice or obligations.
English
Bolts, washers Rubber band
Accessories (For outdoor housing)
This installation should be made by a qualified service
person and should conform to all local codes.
L9BHM_WA(VA-80BW)(GB_JP).book 0 ページ ２００６年１２月２７日 水曜日 午前１１時１９分
1
Indoor Type
Make sure to also consult the relevant instruction manuals.
1
Mark the locations on the wall and drill the
holes for the cables and screws.
And pull out the cables from the wall hole and
pass them through the bracket as shown in
the figure.
2
Fix the bracket to the wall using commercially
available screws (A) in 4 places.
3
Mount the power board unit onto the
attachment.
(1)Pass the screws supplied with the
attachment through each of the power board
unit screw holes (B) and fasten them loosely
using washers (4 places).
(2) Align the blue sticker (C) on the attachment
and the arrow (C) of the same color on the
power board unit, and tighten firmly the
screws loosely fastened in the previous
step.
4
With sticker (D) facing toward you, fix the
attachment onto the bracket using the 4 bolts
(E) supplied with the attachment.
• To fix the attachment, use the hexagonal
wrench supplied with the attachment.
• Make sure that the attachment is fixed, then
peel-off the sticker.
5
Connect the cables to the power board unit
and mount the camera unit onto it.
☞ For details, please refer to Installation Manual that
comes with the camera unit.
“Connections and Settings”
“Surface Mount”
• Be sure to fix the bracket securely using M8 (5/16”)
screws. Using other bolt sizes may cause the
bracket to fall together with the camera on it.
• Route the connected cables so that they do not
touch the power board unit and other parts.
a
b
E
Attachment accessories
Screws, washers
(for power borad
unit)
Hexagonal
wrench
Bolts (10 mm/0.4”)
a
b
A
B
B
B
B
A
E
D
E
3
M8 (5/16”): 40 mm (1.6”) or more
Video cable
Connection cables
Power Board Unit:
VA-84S/80S
Attachment: VA-80A
C; Blue
L9BHM_WA(VA-80BW)(GB_JP).book 1 ページ ２００６年１２月２７日 水曜日 午前１１時１９分
2
Make sure to also consult the relevant instruction manuals.
1
Mark the locations on the wall and drill the
holes for the cables and screws.
And pull out the cables from the wall hole and
pass them through the bracket as shown in
the figure.
2
Fix the bracket to the wall using commercially
available screws (A) in 4 places.
3
Mount the dome cover and the power board
unit onto the housing.
☞ For details, please refer to the Outdoor Housing
Instruction Manual.
“1. Attaching the dome cover”
“2. Mounting the power board unit”
4
Attach the supplied rubber bands (B) to the
housing as shown in the figure.
5
With sticker (C) facing toward you,
temporarily mount the housing on the
bracket.
6
Fix the housing onto the bracket using 4 sets
of supplied bolts and bolt washers (D).
• To fix the housing, use the hexagonal wrench
supplied with the housing.
• Make sure that the housing is fixed, peel off the
sticker, then remove the rubber band.
7
Connect the cables to the power board unit
and mount the camera unit onto it.
☞ For details, please refer to the Outdoor Housing
Instruction Manual.
“3. Connecting cables”
“4. Mounting the camera unit”
• Be sure to fix the bracket securely using M8 (5/16”)
screws. Using other bolt sizes may cause the
bracket to fall together with the camera on it.
• Route the connected cables so that they do not
touch the power board unit and other parts.
Outdoor Type
This mounting bracket can be installed on a pole or a wall
corner by using the appropriate mounting adaptor. For
installation details, refer to the instruction manual for the pole
mounting adaptor (VA-80AP) or the corner mounting adaptor
(VA-80AC).
3
3
D
D
C
A
A
B
M8 (5/16”): 40 mm (1.6”) or more
Video cable
Connection cables
Outdoor Housing: VA-80EX
Dome Cover:
• VA-CM8C (Clear)
• VA-CM8S (Smoked)
Video cable
Power Board Unit:
VA-84S/80S
1. Attaching the dome cover
2. Mounting the power board unit
L9BHM_WA(VA-80BW)(GB_JP).book 2 ページ ２００６年１２月２７日 水曜日 午前１１時１９分
/
