Ops-Core Multi-Hit Handgun Face Shield Operating instructions

Ops-Core
Brand
Ops-Core
Model
Multi-Hit Handgun Face Shield
Type
Operating instructions

Ops-Core Multi-Hit Handgun Face Shield

The Ops-Core Multi-Hit Handgun Face Shield is a versatile piece of protective equipment designed to provide superior defense against multiple impacts from handgun threats. Its robust construction and innovative features make it an ideal choice for law enforcement, military, and security personnel.

Key Features:

  • Multi-hit protection: Engineered to withstand multiple impacts from handgun rounds, ensuring maximum protection in high-risk situations.
  • ARC (Accessory Rail Connector) mounting system: Securely attaches to Ops-Core FAST, MT, and Sentry helmets, as well as Gentex ACH/TBH helmets, providing a stable and reliable mount.

Ops-Core Multi-Hit Handgun Face Shield

The Ops-Core Multi-Hit Handgun Face Shield is a versatile piece of protective equipment designed to provide superior defense against multiple impacts from handgun threats. Its robust construction and innovative features make it an ideal choice for law enforcement, military, and security personnel.

Key Features:

  • Multi-hit protection: Engineered to withstand multiple impacts from handgun rounds, ensuring maximum protection in high-risk situations.
  • ARC (Accessory Rail Connector) mounting system: Securely attaches to Ops-Core FAST, MT, and Sentry helmets, as well as Gentex ACH/TBH helmets, providing a stable and reliable mount.
INSTALLATION (CONTINUED)
CLEANING & CARE
• Spot-clean with a mild detergent and water.
• Visually check the entire face shield for signs of wear and breakage.
• Clean dust and dirt by using air pressure.
Check that the mounting lock arms work properly.
NOTE: IF ANY DEFECTS ARE FOUND, THE DAMAGED COMPONENTS SHOULD BE REPLACED BEFORE USE.
For FAST
®
, SENTRY, and ACH/TBH Style Helmets
Equiped with OPS-CORE FAST or ACH Accessory Rail Connectors (ARCs) Only.
HANDGUN FACE SHIELD OPERATOR’S MANUAL
© OPS-CORE 2016 UM-1017 REV. A
FORE/AFT POSITIONING
ADJUSTING THE FACE SHIELD
Loosen both Thumb Knobs by rotating counterclockwise.
Locate the desired fore/aft position and tighten both
Thumb Knobs clockwise.
Release both Brake Locking Handles and adjust the face shield to
desired position. Rotate the Brake Locking Handle to secure.
4
5
INTRODUCTION
INSTALLATION
HANDGUN FACE SHIELD KIT INCLUDES:
(1) Handgun Face Shield
ABOUT YOUR HANDGUN FACE SHIELD:
This manual covers the installation and basic operating
instructions for the Ops-Core Handgun Face Shield. The
Handgun Face Shield is designed to t Ops-Core FAST,
MT, and Sentry helmets, and Gentex ACH/TBH helmets.
The face shield features a new ARC mounting mechanism
that allows for secure and stable attachment. When
properly installed, the face shield transforms any helmet
into the ultimate defense against multiple impacts from
handgun threats.
PREPARE THE FACE SHIELD
Rotate both Brake Locking Handles to the
locked position and both Rail Mounting
Handles to the open position.
INSERT CONNECTOR SHOES
FASTEN RAIL MOUNTING HANDLES
Align and insert both Accessory Rail Connector Shoes into
the ARC Rails on your helmet until the T-Lock engages with
the desired ARC Rail slot, using slot 2, 3, or 4 only. Be sure
to align to the same slot on both sides.
Fasten both Rail Mounting Handles to
secure the face shield in place.
3
Accessory Rail Connector (ARC) Shoe
T-Lock
Rail Mounting Handle
Handgun Protective
Face Shield
Gasket
Thumb Knob
Brake Locking
Handle
FEATURES
• Locking mechanism secures face shield in any position, pivots quickly and smoothly
• Gasket reduces amount of liquids from entering between the helmet and face shield
• Fore/Aft adjustment helps accommodate protective mask, eye/sunglasses, goggles, and different facial geometry
• Down stop adjustment screw keeps face shield above shell edge in down position
• Folding arms for smaller storage footprint
  • Page 1 1
  • Page 2 2

Ops-Core Multi-Hit Handgun Face Shield Operating instructions

Ops-Core
Brand
Ops-Core
Model
Multi-Hit Handgun Face Shield
Type
Operating instructions

Ops-Core Multi-Hit Handgun Face Shield

The Ops-Core Multi-Hit Handgun Face Shield is a versatile piece of protective equipment designed to provide superior defense against multiple impacts from handgun threats. Its robust construction and innovative features make it an ideal choice for law enforcement, military, and security personnel.

Key Features:

  • Multi-hit protection: Engineered to withstand multiple impacts from handgun rounds, ensuring maximum protection in high-risk situations.
  • ARC (Accessory Rail Connector) mounting system: Securely attaches to Ops-Core FAST, MT, and Sentry helmets, as well as Gentex ACH/TBH helmets, providing a stable and reliable mount.
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents