Dell P2210T User manual

Brand: Dell

Model: P2210T

Category: TVs & monitors

Type: User manual

Dell™P2210FlatPanelMonitorUser'sGuide

Notes, Notices, and Cautions



Information in this document is subject to change without notice.

©2009-2010DellInc.Allrightsreserved.

Reproduction of these materials in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden.

Trademarks used in this text: Dell and the DELLlogoaretrademarksofDellInc;Microsoft and Windows are either trademarks or registered trademarks of Microsoft Corporation in

the United States and/or other countries.ENERGY STAR is a registered trademark of the U.S. Environmental Protection Agency. As an ENERGY STAR partner, Dell Inc. has

determined that this product meets the ENERGY STAR guidelines for energy efficiency.

Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Dell Inc. disclaims any

proprietary interest in trademarks and trade names other than its own.

Model P2210f & P2210t

January 2010 Rev. A03

About Your Monitor

Setting Up the Monitor

Operating the Monitor

Troubleshooting

Appendix



NOTE: A NOTE indicates important information that helps you make better use of your computer.

CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem.

WARNING: A WARNING indicates a potential for property damage, personal injury or death.

Back to Contents Page



About Your Monitor

Dell™P2210FlatPanelMonitorUser'sGuide

Package Contents

Your monitor ships with the components shown below. Ensure that you have received all the components and contact Dell if something is missing.

Package Contents

Product Features

Identifying Parts and Controls

Monitor Specifications

Plug and Play Capability

Universal Serial Bus (USB) Interface

LCD Monitor Quality and Pixel Policy

Maintenance Guidelines

NOTE: Some items may be optional and may not ship with your Monitor. Some features or media may not be available in certain countries.

NOTE: StandandcablesarenotincludedwhenpurchasedwithOptiPlex™USFF780/OptiPlexSFF980AIOstands.

NOTE: To set up with the respective AIO stand, please refer to the respective stand setup guide for setup instructions.

l Monitor

l Stand

l Power Cable



Product Features

The P2210 flat panel display has an active matrix, thin-film transistor (TFT), liquid crystal display (LCD). The monitor features include:

■ 22-inch (558.68 mm) viewable area display (Measured diagonally).

■ 1680 x 1050 resolution, plus full-screen support for lower resolutions.

■ Wide viewing angle to allow viewing from a sitting or standing position, or while moving from side-to-side.

■ Tilt, swivel, vertical extension and rotate adjustment capability.

■ Removable pedestal and Video Electronics Standards Association (VESA) 100 mm mounting holes for flexible mounting solutions.

■ Plug and play capability if supported by your system.

■ Retractable label card allows convenient access to monitor serial number for technical support and easily hidden away providing label-free clean look.

■ On-Screen Display (OSD) adjustments for ease of set-up and screen optimization.

■ Software and documentation media includes an information file (INF), Image color Matching File (ICM), and product documentation.

■ Energy Saver feature for Energy Star compliance.

■ Security lock slot.

■ Asset Management Capability.

■ Capability to switch from wide aspect to standard aspect ratio while maintaining the image quality.

■ EPEAT Gold Rating.

■ Halogen Reduced.

Identifying Parts and Controls

Front View

l VGA Cable (attached to the monitor)

l DVI Cable

l USB up stream cable (enables the USB ports on the monitor)

l Drivers and Documentation media

l Quick Setup Guide

l Safety Information



Back View



Front View

Front panel controls

Label

Description

Preset Modes (default, but configurable)

Brightness & Contrast (default, but configurable)

Exit

Power (with power light indicator)

Back view

Back view with monitor stand

Label

Description

Use

VESA mounting holes (100 mm x 100 mm -

behind attached base plate)

Wall mount monitor using VESA compatible wall mount kit (100 mm x 100 mm)

Stand removal button

Release stand from monitor.

Security lock slot

Secures monitor with security cable lock

Dell Soundbar mounting brackets

Attaches the optional Dell Soundbar.

Information mark

Help locating regulatory and barcode labels

Cable management slot

Organizes cables by placing them through the slot.

Label Card View



Side View

NOTE:

Monitor shipped with label card fully inserted in USB compartment. Pull out the label card to access the barcode serial number label and regulatory rating label.

Back View with label card pulled out

Front View with label card pulled out

Label

Description

Use

Regulatory label

Lists the regulatory approvals.

Barcode serial number label

To contact Dell for technical support.



Bottom View



Monitor Specifications

Flat Panel Specifications

Left view

Right view

Label

Description

Use

USB downstream ports

Connect your USB devices.

Label card

Provide clean monitor back view when reference to labels is not required.

Bottom view

Bottom view with monitor stand

Label

Description

Use

AC power cord connector

Connect the power cable

DC power connector for Dell Soundbar.

Connect the power cord for the soundbar (optional)

DisplayPort connector

Connect your computer DP cable

DVI connector

Connect your computer DVI cable

VGA connector

Connect your computer VGA cable

USB upstream port

Connect the USB cable that came with your monitor to the monitor and the

computer. Once this cable is connected you can use the USB connectors on

the side and bottom of the monitor.

USB downstream ports

Connect your USB devices. You can only use this connector after you have

connected the USB cable to the computer and USB upstream connector on

the monitor.

Screen type

Active matrix - TFT LCD

Panel type

*[P2210] color gamut (typical) is based on CIE1976 (83%) and CIE1931 (72%) test standards.

Resolution Specifications

Supported Video Modes

Preset Display Modes

Electrical Specifications

Screen dimensions

22 inches (22-inch viewable

image size)

Preset display area:

473.76(H)X296.1(V)

Horizontal

473.76 mm (18.7 inches)

Vertical

296.1 mm (11.7 inches)

Pixel pitch

0.282 mm

Viewing angle

160°(vertical)typical

170°(horizontal)typical

Luminance output

250 CD/m²(typical)

Contrast ratio

1000 to 1 (typical), 10000 to 1

(typical Dynamic Contrast On)

Faceplate coating

Antiglare with hard-coating 3H

Backlight

2-CCFL edgelight system

Response Time

5ms panel typical

Color depth

16.7 million colors

Color Gamut

83%*

Horizontal scan range

30 kHz to 83 kHz (automatic)

Vertical scan range

56Hzto75Hz(automatic)

Maximum preset resolution

1680 X 1050 at 60 Hz

Video display capabilities (DVI & DP playback)

480p, 576p, 720p, 1080p

Display Mode

Horizontal Frequency (kHz)

Vertical Frequency (Hz)

Pixel Clock (MHz)

Sync Polarity (Horizontal/Vertical)

VESA, 720 x 400

31.5

70.0

28.3

-/+

VESA, 640 x 480

31.5

60.0

25.2

-/-

VESA, 640 x 480

37.5

75.0

31.5

-/-

VESA, 800 x 600

37.9

60.3

40.0

+/+

VESA, 800 x 600

46.9

75.0

49.5

+/+

VESA, 1024 x 768

48.4

60.0

65.0

-/-

VESA, 1024 x 768

60.0

75.0

78.8

+/+

VESA, 1152 x 864

67.5

75.0

108.0

+/+

VESA, 1280 x 1024

64.0

60.0

108.0

+/+

VESA, 1280 x 1024

80.0

75.0

135.0

+/+

VESA, 1680 x 1050

65.2

60.0

146.0

-/+

Video input signals

Analog RGB, 0.7 Volts +/- 5%, positive polarity at 75 ohm input

impedance

Digital DVI-D TMDS, 600mV for each differential line, positive polarity at

50 ohm input impedance

DP 1.1a signal input support

Synchronization input signals

TTL levels required and separate syncs (including Trigger points), SOG

(Composite SYNC on green)

AC input

voltage/frequency/current

100 to 240 VAC/50 or 60 Hz + 3 Hz/1.5A (Typical)

Physical Characteristics

Environmental Characteristics

Power Management Modes

IfyouhaveVESA'sDPM™compliancedisplaycardorsoftwareinstalledinyourPC,themonitorcanautomaticallyreduceitspowerconsumptionwhennotin

use. This is referred to as Power Save Mode*. If the computer detects input from keyboard, mouse, or other input devices, the monitor automatically resumes

functioning. The following table shows the power consumption and signaling of this automatic power saving feature:

Inrush current

120 V: 30 A (Max.)

240 V: 60 A (Max.)

Connector type

15-pin D-subminiature, blue

connector; DVI-D, white

connector;DP,black connector.

Signal cable type

Digital: Detachable, DVI-D, Solid

pins, shipped detached from the

monitor

Analog:attachable, D-Sub, 15pins,

shipped attached to the monitor

Dimensions (with stand)

Height (extended)

461.91 mm (18.18 inches)

Height (compressed)

361.91 mm (14.24 inches)

Width

511.77 mm (20.15 inches)

Depth

184.12 mm (7.25 inches)

Dimensions (without stand)

Height

334.17 mm (13.16 inches)

Width

511.77 mm (20.15 inches)

Depth

65.00 mm (2.56 inches)

Stand dimensions

Height (extended)

363.82 mm (14.32 inches)

Height (compressed)

323.52mm (12.74 inches)

Width

279.92 mm (11.02 inches)

Depth

184.12 mm (7.25 inches)

Weight

Weight with packaging

18.2 lb (8.25 kg)

Weight with stand assembly and cables

14.22 lb (6.45 kg)

Weight without stand assembly

(For wall mount or VESA mount considerations -

no cables)

9.97 lb (4.52kg)

Weight of stand assembly

3.88 lb (1.76 kg)

Temperature



Operating

0°to40°C

Non-operating

Storage: -20°to60°C(-4°to140°F)

Shipping: -20°to60°C(-4°to140°F)

Humidity

Operating

10% to 80% (non-condensing)

Non-operating

Storage: 5% to 90% (non-condensing)

Shipping: 5% to 90% (non-condensing)

Altitude

Operating

3,657.60 m (12,000 ft) max

Non-operating

12,192 m (40,000 ft) max

Thermal dissipation

88.77 BTU/hour (maximum)

75.12 BTU/hour (typical)

VESA Modes

Horizontal Sync

Vertical Sync

Video

Power Indicator

Power Consumption

Normal

Active

Blue

22 W (typical)

The OSD will only function in the normal operation mode. When any button is pressed in Active-off mode, one of the following messages will be displayed:

Activate the computer and the monitor to gain access to the OSD.

* Zero power consumption in OFF mode can only be achieved by disconnecting the main cable from the monitor.

Pin Assignments

VGA Connector

DVIConnector

operation

Active-off mode

Inactive

Blanked

Amber

Less than 0.3 W

Switch off

-

-

-

Off

Less than 0.3 W



NOTE: This monitor is ENERGY STAR

-compliant as well as TCO '03 power management compatible.

Number

15-pin Side of the Connected Signal Cable

Video-Red

Video-Green

Video-Blue

GND

Self-test

GND-R

GND-G

GND-B

Computer 5V/3.3V

GND-sync

GND

DDC data

H-sync

V-sync

DDC clock

DisplayPort Connector

Number

24-pin Side of the Connected Signal Cable

TMDS RX2-

TMDS RX2+

TMDS Ground

Floating

DDC Clock

DDC Data

Floating

TMDS RX1-

TMDS RX1+

TMDS Ground

Floating

+5V/+3.3V power

Selftest

Hot Plug Detect

TMDS RX0-

TMDS RX0+

TMDS Ground

Floating

TMDS Ground

TMDS Clock+

TMDS Clock-

Number

20-pin Side of the Connected Signal Cable

ML0(p)

GND

ML0(n)

ML1(p)

GND

ML1(n)

ML2(p)

GND

ML2(n)

Plug and Play Capability

You can install the monitor in any Plug and Play-compatible system. The monitor automatically provides the computer system with its Extended Display

Identification Data (EDID) using Display Data Channel (DDC) protocols so the system can configure itself and optimize the monitor settings. Most monitor

installations are automatic; you can select different settings if desired. For more information about changing the monitor settings, see Operating the Monitor.

Universal Serial Bus (USB) Interface

This section gives you information about the USB ports that are available on the left side of your monitor.

USB Upstream Connector

USB Downstream Connector

ML3(p)

GND

ML3(n)

GND

AUX(p)

GND

AUX(n)

HPD

Re-PWR

PWR

NOTE: This monitor supports High-Speed Certified USB 2.0 interface.

Transfer speed

Data Rate

Power Consumption

High speed

480 Mbps

2.5W(Max.,eachport)

Full speed

12 Mbps

2.5W(Max.,eachport)

Low speed

1.5 Mbps

2.5W(Max.,eachport)

Pin Number

4-pin Side of the Connector

DMU

VCC

DPU

GND

Pin Number

4-Pin Side of the Signal Cable

VCC

DMD

DPD

GND

USB Ports

l 1 upstream - back

l 4 downstream - 2 on back; 2 on left side

LCD Monitor Quality and Pixel Policy

During the LCD Monitor manufacturing process, it is not uncommon for one or more pixels to become fixed in an unchanging state which are hard to see and

do not affect the display quality or usability.For more information on Dell Monitor Quality and Pixel Policy, see Dell Support site at: support.dell.com.

Maintenance Guidelines

Cleaning Your Monitor

For best practices, follow the instructions in the list below while unpacking, cleaning, or handling your monitor:

l To clean your antistatic screen, lightly dampen a soft, clean cloth with water. If possible, use a special screen-cleaning tissue or solution suitable for the

antistatic coating. Do not use benzene, thinner, ammonia, abrasive cleaners, or compressed air.

l Use a lightly-dampened,warmclothtocleanthemonitor.Avoidusingdetergentofanykindassomedetergentsleaveamilkyfilmonthemonitor.

l If you notice white powder when you unpack your monitor, wipe it off with a cloth.

l Handleyourmonitorwithcareasadarker-colored monitor may scratch and show white scuff marks more than a lighter-coloredmonitor.

l To help maintain the best image quality on your monitor, use a dynamically changing screen saver and turn off your monitor when not in use.



  

Back to Contents Page

NOTE:USB2.0functionalityrequiresaUSB2.0-

capablecomputer

NOTE:

The monitor's USB interface works only when the monitor is on or in power save mode. If you turn off the monitor and then turn it on, the attached peripherals may

take a few seconds to resume normal functionality.

WARNING: Read and follow the safety instructionsbeforecleaningthemonitor.

WARNING:Beforecleaningthemonitor,unplugthemonitorpowercablefromtheelectricaloutlet.

Back to Contents Page



Appendix

Dell™P2210FlatPanelMonitorUser'sGuide

Safety Instructions

FCC Notice (U.S. Only) and Other Regulatory Information

Contacting Dell



WARNING: Safety Instructions

For information on safety instructions, see the Product Information Guide.

FCC Notices (U.S. Only) and Other Regulatory Information

For FCC notices and other regulatory information, see the regulatory compliance website located at www.dell.com\regulatory_compliance.

Contacting Dell

For customers in the United States, call 800-WWW-DELL (800-999-3355).

Dell provides several online and telephone-based support and service options. Availability varies by country and product, and some services may not be

available in your area. To contact Dell for sales, technical support, or customer service issues:



Back to Contents Page

WARNING: Use of controls, adjustments, or procedures other than those specified in this documentation may result in exposure to shock,

electrical hazards, and/or mechanical hazards.

NOTE:

If you do not have an active Internet connection, you can find contact information on your purchase invoice, packing slip, bill, or Dell product catalog.

Visit support.dell.com.

Verify your country or region in the Choose A Country/Region drop-downmenuatthebottomofthepage.

Click Contact Us on the left side of the page.

Select the appropriate service or support link based on your need.

Choose the method of contacting Dell that is convenient for you.

Back to Contents Page

Setting Up Your Monitor

Dell™P2210FlatPanelMonitor

IfyouhaveaDell™desktoporaDell™portablecomputerwithinternetaccess

1. Go to http://support.dell.com,enteryourservicetag,anddownloadthelatestdriverforyourgraphicscard.

2. After installing the drivers for your Graphics Adapter, attempt to set the resolution to 1680 x 1050 again.

Back to Contents Page

NOTE:

Ifyouareunabletosettheresolutionto1680x1050,pleasecontactDell™toinquireaboutaGraphicsAdapterthatsupportstheseresolutions.

Back to Contents Page

Setting Up Your Monitor

Dell™P2210FlatPanelMonitor

IfyouhaveanonDell™desktop,portablecomputer,orgraphicscard

In Windows XP

1. Right-click on the desktop and click Properties.

2. Select the Settings tab.

3. Select Advanced.

4. Identify your graphics controller supplier from the description at the top of the window (e.g. NVIDIA, ATI, Intel etc.).

5. Refer to the graphic card provider website for updated driver (for example, http://www.ATI.com OR http://www.NVIDIA.com ).

6. After installing the drivers for your Graphics Adapter, attempt to set the resolution to 1680 X 1050 again.

In Windows Vista

or Windows

1. Right-click on the desktop and click Personalization.

2. Click Change Display Settings.

3. Click Advanced Settings.

4. Identify your graphics controller supplier from the description at the top of the window (e.g. NVIDIA, ATI, Intel etc.).

5. Refer to the graphic card provider website for updated driver (for example, http://www.ATI.com OR http://www.NVIDIA.com ).

6. After installing the drivers for your Graphics Adapter, attempt to set the resolution to 1680 X 1050 again.

Back to Contents Page

NOTE: If you are unable to set the resolution to 1680 x 1050, please contact the manufacturer of your computer or consider purchasing a graphics

adapterthatwillsupportthevideoresolutionof1680x1050.

Back to Contents Page



Operating the Monitor

Dell™P2210FlatPanelMonitorUser'sGuide

Using the Front Panel Controls

Using the On-Screen Display (OSD) Menu

Setting the Maximum Resolution

Using the Dell Soundbar (Optional)

Using the Tilt, Swivel, and Vertical Extension

Rotating the monitor

Adjusting the Rotation Display Settings of Your System

Using the Front Panel

Use the control buttons on the front of the monitor to adjust the characteristics of the image being displayed. As you use these buttons to adjust the controls,

an OSD shows the numeric values of the characteristics as they change.

The following table describes the front panel buttons:

Front panel Button

Description



Shortcut

key/

PresetModes

Use this button to choose from a list of preset color modes.

Shortcut key /

Brightness/Contrast

Use this button to directly access the "Brightness/Contrast" menu or to increase the values of the selected menu

option.

Use the MENU button to launch the on-screen display (OSD) and select the OSD Menu. See Accessing the Menu

System.

Exit

Use this button to go back to the main menu or exit the OSD main menu.

Using the On-Screen Display (OSD) Menu



Accessing the Menu System

1. Push the button to launch the OSD menu and display the main menu.

Main Menu for analog (VGA) Input

Main Menu for digital (DVI) Input

Main Menu for display (DP) Input

Power

(withpowerlight

indicator)

Use the Power button to turn the monitor on and off.

The Blue LED indicates the monitor is on and fully functional. An amber LED indicates DPMS power save mode.



NOTE: IfyouchangethesettingsandtheneitherproceedtoanothermenuorexittheOSDmenu,themonitorautomaticallysavesthosechanges.The

changes are also saved if you change the settings and then wait for the OSD menu to disappear.

2.Push the and buttons to move between the setting options. As you move from one icon to another, the option name is highlighted. See the

followingtableforacompletelistofalltheoptionsavailableforthemonitor.

3.Push the buttononcetoactivatethehighlightedoption.

4.Push and button to select the desired parameter.

5. Push to enter the slide bar and then use the  and buttons, according to the indicators on the menu, to make your changes.

6.Select the option to return to the main menu or exit the OSD menu.

NOTE: AUTO ADJUST is only available when you use the analog (VGA) connector.

Icon

Menu and

Submenus

Description



Brightness/Contrast

Use this menu to activate Brightness/Contrast adjustment.

Brightness

Brightness adjusts the luminance of the backlight.

Push the button to increase brightness and push the button to decrease brightness (min 0 ~ max 100).

Contrast

Adjust Brightness first, and then adjust Contrast only if further adjustment is necessary.

Push the button to increase contrast and push the button to decrease contrast (min 0 ~ max 100).

The Contrast function adjusts the degree of difference between darkness and lightness on the monitor screen.

Dynamic Contrast

Dynamic Contrast adjusts the contrast ratio to 10000:1.

Push the button to select the Dynamic Contrast "On" or "Off" .



Auto Adjust

Even though your computer recognizes your monitor on startup, the Auto Adjustment

function optimizes the display settings for use

with your particular setup.

Auto Adjustment allows the monitor to self-

adjust to the incoming video signal. After using Auto Adjustment, you can further tune

your monitor by using the Pixel Clock

(Coarse) and Phase (Fine) controls under Image Settings.



NOTE: Inmostcases,AutoAdjustproducesthebestimageforyourconfiguration.

NOTE: Auto Adjust option is only available when you are using the analog (VGA) connector.

Input Source

Use the Input Source menu to select between different video signals that may be connected to your monitor.



Auto Select

Push to select the Auto Select, the monitor will auto detect either VGA input or DVI-D input.

VGA

Select VGA input when you are using the analog (VGA) connector. Push to select the VGA input source.

DVI-D

Select DVI-D input when you are using the Digital (DVI) connector. Push to select the DVI input source.

DisplayPort

Select DisplayPort input when you are using the DisplayPort (DP) connector. Push

to select the DisplayPort input source.



Color Settings

Use the Color Settings to adjust the color setting mode and color temperature.

There are different color setting sub-menus for VGA/DVI-D and Video input.



Input Color Format

Choose the RGB option if monitor is connected to a computer or a DVD using a VGA or DVI cable. Choose the YPbPr option if monitor is

connected to a DVD by a YPbPr to VGA or YPbPr to DVI cable or if the DVD color output setting is not RGB.



Mode Selection

You can choose Graphics or Video according to the input signal.

l Graphics: Select this mode if your monitor is connected to your computer.

l Video: Select this mode if your monitor is connected to a DVD player.





Preset Modes

When you select Graphics, you can choose Standard, Multimedia, Game, Warm, Cool, or Custom (RGB);

l Standard: Loads the monitor's default color settings. This is the default preset mode.

l Multimedia: Loads color settings ideal for multimedia applications.

l Game: Loads color settings ideal for most gaming applications.

l Warm: Increase the color temperature. The screen appears warmer with a red/yellow tint.

l Cool: Decreases the color temperature. The screen appears cooler with a blue tint.

l Custom (RGB)

: Allows you to manually adjust the color settings. Press the and buttons to adjust the three colors (R, G, B)

values and create your own preset color mode.

When you select Video, you can choose Movie, Game, Sports, or Nature preset:

l Movie: Loads color settings ideal for movies. This is the default preset mode.

l Game: Loads color settings ideal for game.

l Sports: Loads color settings ideal for sports.

l Nature: Loads color settings ideal for nature.



Hue

This feature can shift color of video image to green or purple. This is used to adjust the desired flesh tone color. Use or to adjust the

hue from '0' to '100' .

Press to increase the green shade of the video image.

Press to increase the purple shade of the video image.

NOTE: Hue adjustment is available only for video input.



Saturation

This feature can adjust the color saturation of the video image. Use or to adjust the saturation from '0' to '100'.

Press to increase the monochrome appearance of the video image.

Press to increase the colorful appearance of the video image.

NOTE: Saturation adjustment is available only for video input.



Reset Color Setting

Reset your monitor color settings to the factory settings.

Page is loading ...

Dell P2210T User manual

Brand: Dell

Model: P2210T

Category: TVs & monitors

Type: User manual

Download PDF

report

Dell P2210T User manual

Dell P2210T User manual

Related papers

Other documents