Samsung 305t Quick start guide

Brand: Samsung

Model: 305t

Type: Quick start guide

This manual is also suitable for

305TPLUS

LCD MONITOR

quick start guide

305TPLUS

Please make sure the following items are included with your monitor.

If any items are missing, contact your dealer.

Contact a local deale

to bu

tional items.

Unpacking

Manual

Quick Setup Guide

Warranty Card

(Not available in all

locations)

User's Guide

Cable

DVI-D

(

Dual link

)

Cable

Power Cord

Sold se

aratel

USB Cable

(

A-B T

e cable

)

Front

1. Brightness button

[]

Push the button to adjust brightness.

▼

: The screen is getting dark.

▲

: The screen is getting bright.

2. Power button

[]

/ Power indicator

Turns the monitor on/off.

/ The blue light is on in its normal working condition and blinks

when setting the adjustments of the monitor.

See PowerSaver described in the manual for further information regarding power saving

functions. For energy conservation, turn your monitor off when it is not needed, or when

leaving it unattended for long periods.

Rear

(The configuration at the back of the monitor may vary from product to product.)

1. DOWN :

Connect the

DOWN

port of the USB monitor and a USB

device with the USB cable.

2. UP :

Connect the

port of the monitor and the USB port of the

computer with the USB cable.

To use DOWN, you have to connect the

UP to the PC.

Make sure to use the USB cable supplied with

this monitor to connect the monitor's UP port

and

our com

uter's USB

ort.

DVI IN

Connect the DVI-D (Dual link) Cable to the

DVI IN

port on the

back of your monitor.

By using DVI-D (Dual link), you can expect

twice faster speed and improved signal

quality than those of DVI-D (single link).

It is strongly recommended using DVI-D (Dual

link) Cable for the best quality and speed.

1. ON [ | ] / OFF [O]

Switch the monitor on and off.

2. POWER

Connect the power cord for your monitor to the

POWER

port

on the back of the monitor.

Kensington Lock

The Kensington lock is a device used to physically fix the

system when using it in a public place.

(The locking device has to be purchased separately.)

For using a locking device, contact where you

purchase it.

Stand Stopper

Remove the fixing pin on the stand to lift the monitor up and

down.

See Connecting the Monitor for further information regarding cable connections.

Connectin

the Monitor

Connect the power cord for your monitor to the

POWER

port on the back of the monitor.

Plug the power cord for the monitor into a nearby outlet.

Using the DVI (Digital) connector on the video card.

Connect the DVI-D (Dual link) Cable to the

DVI IN

Port on the back of your Monitor.

[ DVI IN]

Turn on your computer and monitor. If your monitor displays an image, installation is

completed.

Connectin

USB

You can use a USB device such as a mouse, keyboard, Memory Stick, or external hard

disk drive by connecting them to the

DOWN

port of the monitor without connecting

them to the PC.

The USB port of the monitor supports High-Speed Certified USB 2.0.

High speed Full speed Low speed

Data Rate 480 Mbps 12 Mbps 1.5 Mbps

Power Consumption

2.5W

(Max., each port)

2.5W

(Max., each port)

2.5W

(Max., each port)

Connect the

port of the monitor and the USB port of the computer with the USB cable.

Connect the

DOWN

port of the USB monitor and a USB device with the USB cable.

The use procedures are as the same as those for using an external device connecting to the

PC.

z You can connect and use a keyboard and mouse.

z You can play a file from a media device.

(Examples of media devices: MP3, digital camera, etc.)

z You can run, move, copy or delete the files on the storage device.

(Examples of storage devices: external memory, memory card, memory reader, HDD-type

MP3 player, etc.)

z You can use other USB devices that can be connected to a computer.

To use

DOWN

port, you have to connect the UP (Upstream Cable) to the PC.

Make sure to use the USB cable supplied with this monitor to connect the

monitor's UP port and your computer's USB port.

When connecting a device to the DOWN port of the monitor, connect the

device using a cable appropriate to the device.

(For the purchase of the cable and external devices, ask the service center of

the corresponding product.)

The company is not liable for problems or damages to an external device

caused by using an unauthorized cable for the connection.

Some products do not follow the USB standard, and it may cause a

malfunction of the device.

If the device malfunctions even if it is connected to the computer, contact the

service center of the device/computer.

Usin

the Stand

Slidin

stand

Stand Stoppe

Swivel stand

Using ( ),You can swivel the monitor left and right at an angle of 90° to set the monitor

lengthwise. The rubber under the stand is to avoid the monitor slide.

Tilt an

Using ( ), You can adjust the tilt anlgle within a range of 3° forward to 25° backward for the

most comfortable viewing angle.

Attaching a Base

This monitor accepts a 200 mm x 100 mm / 100 mm x 100 mm VESA-compliant Mounting

interface pad.

Monitor

Mounting interface pad (Sold separately)

1. Turn off your monitor and unplug its power cord.

2. Lay the LCD monitor face-down on a flat surface with a cushion beneath it to protect the

screen.

3. Remove four screws and then remove the stand from the LCD monitor.

4. Align the Mounting interface pad with the holes in the rear cover mounting pad and secure it

with four screws that came with the arm-type base, wall mount hanger or other base.

z Do not use screws longer than the standard dimension, as they may damage the inside

of the Monitor.

z For wall mounts that do not comply with VESA standard screw specifications, the length

of the screws may differ depending on their specifications.

z Do not use screws that do not comply with the VESA standard screw specifications.

Do not fasten the screws too tightly, as this may damage the product or cause the

product to fall, leading to personal injury.

Samsung is not liable for these kinds of accidents.

Samsung is not liable for product damage or personal injury when a non-VESA or non-

specified wall mount is used or the consumer fails to follow the product installation

instructions.

z To mount the monitor on a wall, you should purchase the wall mounting kit that allows

you to mount the monitor at least 10 cm away from the wall surface.

Contact the nearest Samsung Service Center for more information. Samsung

Electronics will not be responsible for damages caused by using a base other than

those specified.

Please use Wall Mount according to the International standards.

Check List

Before calling for service, check the information in this section to see if you can remedy any

problems yourself. If you do need assistance, please call the phone number on the

Information section or contact your dealer.

Symptom Check List Solutions

No images on the

screen. I cannot turn

on the monitor.

Is the power cord connected

properly?

Check the power cord connection

and supply.

If the power is on, reboot the

computer to see the initial

screen(the login screen),

which can be seen.

If the initial screen (the login screen)

appears, boot the computer in the

applicable mode (the safe mode for

Windows ME/XP/2000) and then

change the frequency of the video

card.

(Refer to Preset Timing Modes)

Note : If the initial screen (the login

screen) does not appear, contact

the Service Center or your dealer.

There is no image on the

screen.

Is the power indicator on the

monitor blinking at 1 second

intervals?

The monitor is in PowerSaver mode.

press any key on the keyboard to

activate the monitor and restore the

image on the screen.

The screen shows

strange colors or just

black and white.

Is the screen displaying only

one color as if looking at the

screen through a cellophane

paper?

Check the signal cable connection.

Make sure the video card is fully

inserted in it's slot.

Have the screen colors

become strange after

running a program or due to

a crash between

applications?

Reboot the computer.

Has the video card been set

properly?

Set the video card by referring to the

video card manual.

The screen suddenly

has become

unbalanced.

Have you adjusted the

resolution or frequency to the

monitor?

Adjust the resolution and frequency

at the video card.

(Refer to Preset Timing Modes).

LED is blinking but no

images on the screen.

Is the frequency properly

adjusted when checking the

Display Timing on the menu?

Adjust the frequency properly by

referring to the video card manual

and Preset Timing Modes.

(The maximum frequency per

resolution may differ from product to

product.)

There are only 16

colors shown on the

screen.

The screen colors

have changed after

changing the video

card.

Have the Windows colors

been set properly?

Windows ME/2000/XP :

Set the colors properly at the

Control Panel

→

Display

→

Settings

Has the video card been set

properly?

Set the video card by referring to the

video card manual.

I cannot use the

2560x1600 resolution

with the monitor.

Does the graphics card on

your computer support the

2560x1600 resolution?

If your graphics card does not support the

2560x1600 resolution, then you can only

use the 1280x800 resolution with your

monitor.

To use the 2560x1600 resolution, replace

your graphics card with one that supports

that resolution.

Check the following items if there is trouble with the monitor.

1. Check if the power cord and the video cables are properly connected to the computer.

2. Check if the computer beeps more than 3 times when booting.

(If it does, ask the service center to check the main board of the computer.)

3. If you installed a new video card or if you assembled the PC, check if the installed the adapter

(video) driver.

4. Check if the scanning ratio of the video screen is set at 60Hz +/- 2Hz.

(Do not exceed 60 Hz when using the maximum resolution.)

5. If you have problems in installing the adapter (video) driver, boot the computer in Safe Mode,

remove the Display Adapter at the "

Control Panel

→

System

→

Device Administrator

" and then

reboot the computer to reinstall the adapter (video) driver.

If problems repeatedly occur, contact an authorized Service Center.

Q & A

Question

Answer

How can I change the

frequency?

The frequency can be changed by reconfiguring the video card.

Note that video card support can vary, depending on the version

of the driver used. (Refer to the computer or the video card

manual for details.)

How can I adjust the resolution? Windows ME/XP/2000 : Set the resolution at the Control

Panel

→

Display

→

Settings.

* Contact the video card manufacturer for details.

How can I set the Power Saving

function?

Windows ME/XP/2000 : Set the function at BIOS-SETUP of the

computer or the screen saver. (Refer to Windows/Computer

Manual).

How can I clean the outer

case/LCD Panel?

Disconnect the power cord and then clean the monitor with a soft

cloth, using either a cleaning solution or plain water.

Do not leave any detergent or scratches on the case. Do not let

any water enter the monitor.

Samsung 305t Quick start guide

Brand: Samsung

Model: 305t

Type: Quick start guide

This manual is also suitable for

305TPLUS

Download PDF

report

Samsung 305t Quick start guide

This manual is also suitable for

Samsung 305t Quick start guide

Related papers

Other documents