AireRyder LK51213OBB Installation guide

AireRyder
Brand
AireRyder
Model
LK51213OBB
Category
Household fans
Type
Installation guide

AireRyder LK51213OBB is a light kit that can be installed on a ceiling fan or as a semi-flush mount. It includes an E26 medium base spiral fluorescent bulb with a maximum wattage of 13W. The light kit comes with a pull chain for easy operation and a glass shade for a stylish look. It is easy to install, with detailed instructions provided in the manual. The light kit is compatible with most ceiling fans and can also be used as a standalone light fixture. Whether you need to brighten up your living room, bedroom, or office, the AireRyder LK51213OBB is a great choice.

AireRyder LK51213OBB is a light kit that can be installed on a ceiling fan or as a semi-flush mount. It includes an E26 medium base spiral fluorescent bulb with a maximum wattage of 13W. The light kit comes with a pull chain for easy operation and a glass shade for a stylish look. It is easy to install, with detailed instructions provided in the manual. The light kit is compatible with most ceiling fans and can also be used as a standalone light fixture. Whether you need to brighten up your living room, bedroom, or office, the AireRyder LK51213OBB is a great choice.

ASSEMBLY AND INSTALLATION
INSTRUCTIONS
WARNING: BE SURE TO SHUT OFF POWER AT THE MAIN FUSE OR CIRCUIT
BREAKER BOX BEFORE INSTALLING OR SERVICING THIS FIXTURE.
NOTE: 1. Before installing, consult local electrical codes for wiring and grounding requirements.
2. The combined weight of your ceiling fan and light kit cannot exceed 35 pounds unless
additional support is provided for the fan.
LK51213
1. Remove the switch box cover from the switch
box of the fan by loosing the three switch box
screws.
2. Unscrew the center plug from the switch box
cover and discard it.
3. Thread the fixture wire through the switch box
cover.
4. Attach the switch box cover to the light kit, then
secure it with a washer and hex nut.
5. Thread the pull chain through a hex nut and the
short nipple. Screw the short nipple into the
coupling and secure it with a hex nut.
6. Cut the redundant wires if necessary. Pull out
the wires from the switch box. Make wire
connections using the wire nuts:
---The black wire from the light kit to the black
(or blue) wire from the switch box.
---The white wire from the light kit to the white
wire from the switch box.
Carefully put the wires back into the switch box.
7. Attach the switch box cover back to the switch box
using the three switch box screws.
8. Install bulbs (included). See relamping label at socket
area or packaging for maximum allowed wattage.
9. Slip the glass shade up through the pull chain and the short nipple, secure them with a rubber
pad, metal pad and hex nut.
10. Slip the cover up through the pull chain and the short nipple, secure it with finial.
11. Turn on the power at the main fuse or circuit breaker box.
(You can control the light with the pull chain)
Center Plug
Black Wire
Wire Nut
Black or Blue Wire
White Wire
White Wire
Switch Box
Motor
Hex Nut & Washer
Stem
Switch Box Cover
Switch Box Screw
For Light Kit:
LK51213 --- Page 1
Light Kit
Hex Nut
Rubber Pad
Metal Pad
Cover
Finial
Short Nipple
Glass Shade
Pull Chain
Hex Nut
Coupling
E26 medium base spiral
fluorescent Bulb
(Max.13W, incluced)
090406
F A N C OF A N C O
1. Take out the parts from the hardware package For
Semi-Flush.
2. Attach two screws to the mounting strap, and secure
it with two lock nuts. Adjust the length of the screws
if necessary.
3. Attach the mounting strap to the outlet box by using
two mounting screws.
4. Follow step 5 as For Light Kit.
5. Thread the fixture wires through the coupling, hex nut,
long nipple, big tube, cap, canopy, metal pad, washer,
grounding pad and another hex nut.
6. Secure the coupling onto the stem on the top of the
light kit. Then screw the long nipple into the coupling,
then secure it with a hex nut.
7. Slip the big tube, cap with the open side facing downward
and the canopy down through the long nipple, secure them
together with a metal pad, washer, grounding pad and hex
nut.
8. Cut the redundant wires if necessary. Pull out
the outlet wires and the house grounding wire
from the outlet box. Make wire connections
using the wire nuts:
---Connect the black wire from fixture to the
black wire from power source.
---Connect the white wire from fixture to the
white wire from power source.
---Attach the fixture grounding wire to the
mounting strap with the green grounding
screw. Then connect it to the house
grounding wire with the wire nut.
Carefully put wires back into the outlet box.
9. Attach the canopy to the mounting strap, and
secure it with the bolt nuts.
10. Follow steps 8~11 as For Light Kit.
For Semi-Flush
LK51213 --- Page 2
E26 medium base spiral
fluorescent Bulb
(Max.13W, incluced)
090406
F A N C OF A N C O
Outlet Box
House Grounding Wire
Wire Nut
Screw
Mounting Strap
Green Grounding Screw
Hex Nut
Grounding Pad
Washer
Metal Pad
Canopy
Bolt Nut
Cap
Big Tube
Long Nipple
Hex Nut
Coupling
Lock Nut
Mounting Screw
Stem
Light Kit
Hex Nut
Rubber Pad
Metal Pad
Cover
Finial
Short Nipple
Glass Shade
Pull Chain
Hex Nut
Coupling
  • Page 1 1
  • Page 2 2

AireRyder LK51213OBB Installation guide

AireRyder
Brand
AireRyder
Model
LK51213OBB
Category
Household fans
Type
Installation guide

AireRyder LK51213OBB is a light kit that can be installed on a ceiling fan or as a semi-flush mount. It includes an E26 medium base spiral fluorescent bulb with a maximum wattage of 13W. The light kit comes with a pull chain for easy operation and a glass shade for a stylish look. It is easy to install, with detailed instructions provided in the manual. The light kit is compatible with most ceiling fans and can also be used as a standalone light fixture. Whether you need to brighten up your living room, bedroom, or office, the AireRyder LK51213OBB is a great choice.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents