AireRyder LK51215OR Installation guide

AireRyder
Brand
AireRyder
Model
LK51215OR
Category
Household fans
Type
Installation guide
ASSEMBLY AND INSTALLATION
INSTRUCTIONS
WARNING: BE SURE TO SHUT OFF POWER AT THE MAIN FUSE OR CIRCUIT
BREAKER BOX BEFORE INSTALLING OR SERVICING THIS FIXTURE.
NOTE: 1. Before installing, consult local electrical codes for wiring and grounding requirements.
2. The combined weight of your ceiling fan and light kit cannot exceed 35 pounds unless
additional support is provided for the fan.
LK51215
1. Remove the switch box cover from the switch box of
the fan by loosing the three switch box screws.
2. Unscrew the center plug from the switch box cover
and discard it. (Fig.1)
3. Slip the short nipple up through the pull chain, and
secure it into the coupling with hex nut. (Fig.3)
4. Slip the tube, small cap with the open side facing
upward and the big cap with the open side facing
downward up through the pull chain and the short
nipple, secure them together with a hex nut.
5. Thread the fixture wire through the switch box cover.
(Fig.1)
6. For fan style that is shown in Fig.1: Attach the nipple
of the light kit to the hole of the switch box cover, then
thread the wires through the washer and hex nut,
then secure them tightly.
7. For fan style that is shown in Fig.2: Thread the fixture
wire through the switch box, then attach the light kit
to the switch box and secure it with two set screws
(6x32 20mmL).
8. Cut the redundant wires if necessary. Pull out the wires from the switch box. Make wire connections
using the wire nuts:
---The black wire from the light kit to the black (or blue) wire from the switch box.
---The white wire from the light kit to the white wire from the switch box.
Carefully put the wires back into the switch box.
9. Attach the switch box cover back to the switch box using the three switch box screws.
10. Install bulbs (included). See relamping label at socket area or packaging for maximum allowed wattage.
11. Slip the glass shade and decorative ring up through the pull chain and the short nipple, secure them with
a hex nut.
12. Slip the cover up through the pull chain and the short nipple, secure it with finial.
13. Turn on the power at the main fuse or circuit breaker box.
(You can control the light with the pull chain)
LK51215 --- Page 1
Coupling
Pull Chain
Big Cap
Glass Shade
Hex Nut
Short Nipple
Tube
Small Cap
Hex Nut
Decorative Ring
Hex Nut
Cover
Finial
For Light Kit:
Light Kit
E26 medium base spiral
fluorescent Bulb
(Max.13W, incluced)
Fig.1
Motor
Switch Box
White Wire
White Wire
Hex Nut
Screw
Switch Box Cover
Nipple
Light Kit
Wire Nut
Washer
Center Plug
Black or Blue Wire
Black Wire
Fig.3
Motor
(6 x 32 20mmL)
Set Screw
Fig.2
Nipple
Screw
Black or Blue Wire
Wire Nut
Black Wire
Motor
Switch Box Cover
White Wire
Terminal (Groove)
Terminal (Tongue)
White Wire
Switch Box
090406
F A N C OF A N C O
1. Take out the parts from the hardware package For
Semi-Flush.
2. Attach two screws to the mounting strap, and secure
it with two lock nuts. Adjust the length of the screws
if necessary.
3. Attach the mounting strap to the outlet box by using
two mounting screws.
4. Thread the fixture wires through the coupling, hex nut,
long nipple, big tube, cap, canopy, metal pad, washer,
grounding pad and another hex nut.
5. Secure the coupling onto the stem on the top of the
light kit. Then screw the long nipple into the coupling,
then secure it with a hex nut.
6. Slip the big tube, cap with the open side facing downward
and the canopy down through the long nipple, secure them
together with a metal pad, washer, grounding pad and hex nut.
7. Follow steps 3~4 as For Light Kit.
8. Cut the redundant wires if necessary. Pull out the outlet wires
and the house grounding wire from the outlet box. Make wire
connections using the wire nuts:
---Connect the black wire from fixture to the
black wire from power source.
---Connect the white wire from fixture to the
white wire from power source.
---Attach the fixture grounding wire to the
mounting strap with the green grounding
screw. Then connect it to the house
grounding wire with the wire nut.
Carefully put wires back into the outlet box.
9. Attach the fixture canopy to the mounting strap,
and secure it with the bolt nuts.
10. Follow steps 10~13 as For Light Kit.
For Semi-Flush
LK51215 --- Page 2
090406
F A N C OF A N C O
Outlet Box
House Grounding Wire
Wire Nut
Screw
Mounting Strap
Green Grounding Screw
Hex Nut
Grounding Pad
Washer
Metal Pad
Canopy
Bolt Nut
Cap
Big Tube
Long Nipple
Hex Nut
Coupling
Lock Nut
Mounting Screw
Stem
Light Kit
E26 medium base spiral
fluorescent Bulb
(Max.13W, incluced)
Coupling
Big Cap
Glass Shade
Hex Nut
Pull Chain
Short Nipple
Tube
Small Cap
Hex Nut
Decorative Ring
Hex Nut
Cover
Finial
  • Page 1 1
  • Page 2 2

AireRyder LK51215OR Installation guide

AireRyder
Brand
AireRyder
Model
LK51215OR
Category
Household fans
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents