Lightolier Fluorescent Downlight and Wall Washer User manual

Brand: Lightolier

Model: Fluorescent Downlight and Wall Washer

Category: Wall clocks

Type: User manual

—

INSTALLATION OF COMPACT FLUORESCENT

DOWNLIGHTS AND WALL WASHERS

INSTRUCTION SHEET NO.

IS:8054CL

0891 Page 1 of 2

READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING FIXTURE. -

This fixture is intended for installation in accordance with the National Electrical Code and local

regulations. To assure full compliance with local codes and regulations,

check with your local electrical

inspector before installation. To prevent electrical shock, turn off electricity at fuse box before

proceeding. This fixture is intended for ceiling mounting and is suitable for damp locations.

Retain these Instructions for maintenance reference. -

INSTALLATION OF DOWNLIGHT

A. INSTALL WHITE TRIM RING

NOTE

Omit this sactlon If reflector is self-flenged.

1. For overlappin trim installation (Fig. 1), slip WHITE TRIM RING

over REFLEC#R, as shown in Fig. 2 and 3.

2. For flangeless trim installation (Fig. 4), WHITE TRIM RING is not

required.

B. SNABIN

Align TABS on SOCKET CUP with openings in REFLECTORand

push in SOCKET CUP until RETAINING SPRING snaps in (Fig. 5).

C. PUSH-UP REFLECTOR

Tilt REFLECTOR and insert SOCKET CUP into ceiling opening on

side opposite JUNCTION BOX. Pivot REFLECTOR and push it up

into ceiling (Fig. 6).

N~E To remove REFLECTOR, disengsge the SOCKET CUP by

depressing the RETAINING SPRING (Fig. 5). Turn REFLECTOR

counterolockwlse while pulling downward. After starting, use

both hands to ramov~ If desired. See Fig. 7.

D. LAMPING

lnserI lamp, tip first through hole in side of reflector opposite lamp

SOCKETS. Bring lamp to horizontal position, line up pins, and push

into socket (Fig.8). To relamp, carefully pull straight out of socket, tilt

base downward, and remove lamp.

INSTALLATION OF LENS WALL WASHER AND OPEN

WALL WASHER

NOTE. aafore Installingreflector,makesurethe mountingframe IS

Installedwith

JUNCTION BOX away from the wall to ba illuminated

(Fig. 10A or 10B).

FOR OPEN WALL WASHER

Remove two RETAINING SPRINGS that are near the JUNCTION BOX from

the MOUNTING FRAME (Fig 9).

Insert two new RETAINING SPRINGS, that are provided with the reflector

trim, into pocket of MOUNTING FRAME (Fig. 9A).

Then squeeze RETAINING SPRING into position with a plier (Fig. 9A).

FIG. 1

,,$y

.—.-

/“

REFLECTOR

OR LENS TRIM

WHITE

TRIM

RING

FIG. 2

FIG. 3

:: .:.

,4.,..,-.

,,. ..

FK3. 4

FIG. 5

TO REMOVE

““E=Jum

RETAINING

SPRING

REMOVED

1 m

FIG. 9 FIG. 9A

wREFLEcTOR

FIG. 6 FIG.

SOCKET

—

,.,,

—

,..

..+jf’

.,5-;:::’;+’

‘..:>~’ ,, ,.

,, ,,,

,,,,,,

,.:,

~x.,:s

FIG. 8

lNSTALIATION OF COMPACT FLUORESCENT

DOWN LIGHTS AND WALL WASHERS (CONT’D)

;2;~54CL

Page 2 of 2

A. SNAPIN

Align TABS on SOCKET CUP with openings in reflector and push in

SOCKET CUP until RETAINING SPRING snaps-in (Fig. 5).

B. INSTALL WHITE TRIM RING

NOTE Omit this section If reflector is self-flanged.

1.For overlapping trim installation (Fig. 1) slip WHITE RING over

LENS TRIM as shown in Fig. 2 and 3.

2. For flangeless trim installation (Fig. 4), WHITE TRIM RING is not

required.

C. PUSH-UP REFLECTOR FOR LENS WALL WASHER

1. Tilt REFLECTOR and insert SOCKET CUP into ceiling opening on

side opposite JUNCTION BOX. Push REFLECTOR up leaving

approximately one inch of the REFLE~R exposed below the

CEILING LINE (Fia. 10A).

LENS WALL WASHER

SOCKET CUP

r JUNCTION

BOX

REFL LEAVE APPROX.

1“ EXPOSED

TITE

Compress TORSl~NTITE SPRINGS on LENS TRIM by squeezing

with fingem. Insert into SLOTS in

REFLECTOR and push up into

REFLECTOR until flush with ceiling (Fig. 11).

NOTE To remove REFLEC70R, lift LENS and pull LENS TRIM down

u“

WALL TO BE ILLUMINATED

(Fig. 12), then disengage the SOCKET CUP by daprsssing the

RETAINING SPRING (Fig.5). lhrn REFLECTOR counterclockwise

while pulling downward. Aftar stafling, use both hands to remove.

See Fig. 7.

FIG. 10A

PUSH-UP REFLECTOR FOR OPEN WALL WASHER

1,Tilt

REFLECTOR and insert SOCKET CUP into ceiling opening on

OPEN WALL WASHER

side opposite JUNCTION BOX. Pivot REFLECTOR and push it up

into ceilina [Fia. 13).

-.-,

NOTE To remove REFLECTOR, disengage the SOCK~ CUP by

daprassing the RETAINING SPRING (Fig. 5). 7urn REFLEC70R

counteroiockwise while pulling downward. After starting, use

both hands to remove If dasired. Saa Fig. 7.

~ b

JUNCTION

BOX

D. LAMPING

Line up pins and push into socket. To relamp, carefully pull lamp

straight out.

CARE AND MAINTENANCE OF A12AK@ REFLECIOR

If handling of reflectors with anodized or Alzak finish is required, the

use of clean white or plastic film gloves is recommended to avoid

fingerprints.

Anodized or Alzak surfaces can be cleaned by the following methods

Wipe off with a soft, clean, dry, lint-free cloth.

Wipe off with a soft clean cloth dampened

in mild detergent

solution. Rinse then wipe dry with lint-free cloth or paper towel.

Wipe off with a clean cloth dampened with a solution of wetting

agent and water (such as 2 oz. per gallon “Pluronic L62-LF” by

Wyandotte Products). Then wipe dry.

Or use a liquid wash such as Glass Wax”. Avoid gritty cleaning

agents.

/-- ‘“’%lON

SOCKET

CUP

-Qi-REFLEcTOR

WALL TO BE ILLUMINATED

FIG. 10B

FIG. 11

FIG.

Lightolier Fluorescent Downlight and Wall Washer User manual

Brand: Lightolier

Model: Fluorescent Downlight and Wall Washer

Category: Wall clocks

Type: User manual

Download PDF

report

Lightolier Fluorescent Downlight and Wall Washer User manual

Lightolier Fluorescent Downlight and Wall Washer User manual

Related papers

Other documents