Lightolier IS:R7029 User manual

Type
User manual

Lightolier IS:R7029 is a wall washer/downlight reflector designed for easy installation and maintenance. It features an adjustable inside reflector that allows for precise positioning of the light beam, making it ideal for illuminating walls, ceilings, and other surfaces. The reflector is made of anodized or Alzak aluminum, which provides excellent reflectivity and durability. The fixture is also equipped with a locking ring that ensures a secure fit and prevents accidental movement.

Here are some of the key features and benefits of the Lightolier IS:R7029:

  • Easy to install and maintain
  • Adjustable inside reflector for precise light beam positioning

Lightolier IS:R7029 is a wall washer/downlight reflector designed for easy installation and maintenance. It features an adjustable inside reflector that allows for precise positioning of the light beam, making it ideal for illuminating walls, ceilings, and other surfaces. The reflector is made of anodized or Alzak aluminum, which provides excellent reflectivity and durability. The fixture is also equipped with a locking ring that ensures a secure fit and prevents accidental movement.

Here are some of the key features and benefits of the Lightolier IS:R7029:

  • Easy to install and maintain
  • Adjustable inside reflector for precise light beam positioning
INSTALLATION OF CALCULITE A-LAMP WALL WASHER/DOWNLIGHT REFLECTOR
INSTRUCTION SHEET FOR ITEMS:
IS:R7029
P7006, P7007, P7008, Q7006, Q7007, Q7008, R7029, R7030, R7031,
0888
S7029, S7030, S7031, T7032, T7033, ~034, U7032, U7033, U7034
READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING FIXTURE.
This fixture is intended for installation in accordance with the National Electrical Code and local or federal code specifications. To prevent
electrical shock, turn off electricity at fuse box before proceeding.
Retain these instructions for maintenance referance.
L MOUNTING SPRING
FIG. 1
I
WARNING—(RISK OF FIRE)DO NOT iNSTALLlNsuLATlON wlTHIN3 INCHESOF FlxTuRE SIDESOR
WIRINGCOMPARTMENT,NOR
ABOVE FlxTURE IN SUCH A MANNER SO AS TO ENTRAP HEAT.
I
A. INSTALL INSIDE REFLECTOR (FIG. 1)
NOTE:
For overlapping trim installation slip on WHITE
TRIM RING over INSIDE REFLECTOR, as shown in Fig.
2 and 3. For flangeless trim installation, WHITE TRIM
RING is not required.
1.
2.
To install INSIDE REFLECTOR in REFLECTOR/
HOUSING with SCREWS (Fig. 4), push INSIDE
REFLECTOR up into REFLECTOR/HOUSING. Align
keyslots in LOCKING RING and insert onto the
SCREWS on REFLECTOR/HOUSING. Rotate INSIDE
REFLECTOR clockwise so that CUT OUT WINDOW is
always opposite the wall to be lighted. Now, tighten
the SCREWS so that INSIDE REFLECTOR is held
firmly against ceiling surface.
To install INSIDE REFLECTOR in REFLECTOR/
HOUSING with THUMB SCREWS (Fig. 5), push
INSIDE REFLECTOR up into REFLECTOR/HOUSING.
Rotate INSIDE REFLECTOR so that CUT OUT
WINDOW is always opposite the wall to be lighted.
Now, tighten the THUMBSCREWS so that INSIDE
REFLECTOR is held firmly against ceiling surface.
B.CARE AND MAINTENANCE OF “ALZAK”
REFLECTOR
If handling of reflectors with anodized or Alzak finish is
required, the use of clean white or plastic film gloves is
recommended to avoid fingerprints.
Anodized or Alzak surfaces can be cleaned by the
following methods:
;.
3.
Wipe-of with a soft, clean, dry, lint-free cloth.
Wipe off with a clean cloth dampened in mild
detergent solution. Rinse, then wipe dry with lint-free
cloth or paper towel.
Wipe off with a clean cloth dampened with a
solution of wetting agent and water (such as 2 oz.
per gallon “Pluronic L62-LF by Wyandotte Products),
or a liquid wax such as Glass Wax”. Then wipe dry.
Avoid gritty cleaning agents.
FIG. 2
WHITE _“
TRIM
RING
FIG. 3
REFLECTORI
HOUSING
7
FIG. 4
,-. ....=
I
~ LOCKING RING
9
REFLECTORI
HOUSING
i=
THUMBSCREW
/
‘\
. \,
CUT OUT ‘–~
‘<
WINDOW
?~
INSIDE
REFLECTOR
i L.-~ ~
——.—
FIG. 5
U.S. Pat. No. 4,039,822
  • Page 1 1

Lightolier IS:R7029 User manual

Type
User manual

Lightolier IS:R7029 is a wall washer/downlight reflector designed for easy installation and maintenance. It features an adjustable inside reflector that allows for precise positioning of the light beam, making it ideal for illuminating walls, ceilings, and other surfaces. The reflector is made of anodized or Alzak aluminum, which provides excellent reflectivity and durability. The fixture is also equipped with a locking ring that ensures a secure fit and prevents accidental movement.

Here are some of the key features and benefits of the Lightolier IS:R7029:

  • Easy to install and maintain
  • Adjustable inside reflector for precise light beam positioning

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI