—
INSTALLATION OF COMPACT FLUORESCENT
DOWNLIGHTS AND WALL WASHERS
INSTRUCTION SHEET NO.
\
IS:8054CL
0891 Page 1 of 2
READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING FIXTURE. -
This fixture is intended for installation in accordance with the National Electrical Code and local
regulations. To assure full compliance with local codes and regulations,
check with your local electrical
inspector before installation. To prevent electrical shock, turn off electricity at fuse box before
proceeding. This fixture is intended for ceiling mounting and is suitable for damp locations.
Retain these Instructions for maintenance reference. -
INSTALLATION OF DOWNLIGHT
A. INSTALL WHITE TRIM RING
NOTE
Omit this sactlon If reflector is self-flenged.
1. For overlappin trim installation (Fig. 1), slip WHITE TRIM RING
over REFLEC#R, as shown in Fig. 2 and 3.
2. For flangeless trim installation (Fig. 4), WHITE TRIM RING is not
required.
B. SNABIN
Align TABS on SOCKET CUP with openings in REFLECTORand
push in SOCKET CUP until RETAINING SPRING snaps in (Fig. 5).
C. PUSH-UP REFLECTOR
1.
Tilt REFLECTOR and insert SOCKET CUP into ceiling opening on
side opposite JUNCTION BOX. Pivot REFLECTOR and push it up
into ceiling (Fig. 6).
N~E To remove REFLECTOR, disengsge the SOCKET CUP by
depressing the RETAINING SPRING (Fig. 5). Turn REFLECTOR
counterolockwlse while pulling downward. After starting, use
both hands to ramov~ If desired. See Fig. 7.
D. LAMPING
lnserI lamp, tip first through hole in side of reflector opposite lamp
SOCKETS. Bring lamp to horizontal position, line up pins, and push
into socket (Fig.8). To relamp, carefully pull straight out of socket, tilt
base downward, and remove lamp.
INSTALLATION OF LENS WALL WASHER AND OPEN
WALL WASHER
NOTE. aafore Installingreflector,makesurethe mountingframe IS
Installedwith
JUNCTION BOX away from the wall to ba illuminated
(Fig. 10A or 10B).
FOR OPEN WALL WASHER
1.
2.
3.
Remove two RETAINING SPRINGS that are near the JUNCTION BOX from
the MOUNTING FRAME (Fig 9).
Insert two new RETAINING SPRINGS, that are provided with the reflector
trim, into pocket of MOUNTING FRAME (Fig. 9A).
Then squeeze RETAINING SPRING into position with a plier (Fig. 9A).
@
FIG. 1
,,$y
.—.-
1
..
..
/“
REFLECTOR
OR LENS TRIM
WHITE
TRIM
RING
FIG. 2
FIG. 3
@
:: .:.
Y.
.
,4.,..,-.
,,. ..
FK3. 4
FIG. 5
TO REMOVE
““E=Jum
RETAINING
SPRING
REMOVED
1 m
*
v
/
FIG. 9 FIG. 9A
wREFLEcTOR
FIG. 6 FIG.
SOCKET
n
—
,.,,
—
,..
..+jf’
.,5-;:::’;+’
‘..:>~’ ,, ,.
,, ,,,
,,,,,,
,.:,
~x.,:s
..
FIG. 8
7
lNSTALIATION OF COMPACT FLUORESCENT
DOWN LIGHTS AND WALL WASHERS (CONT’D)
;2;~54CL
Page 2 of 2
A. SNAPIN
Align TABS on SOCKET CUP with openings in reflector and push in
SOCKET CUP until RETAINING SPRING snaps-in (Fig. 5).
B. INSTALL WHITE TRIM RING
NOTE Omit this section If reflector is self-flanged.
1.For overlapping trim installation (Fig. 1) slip WHITE RING over
LENS TRIM as shown in Fig. 2 and 3.
2. For flangeless trim installation (Fig. 4), WHITE TRIM RING is not
required.
C. PUSH-UP REFLECTOR FOR LENS WALL WASHER
1. Tilt REFLECTOR and insert SOCKET CUP into ceiling opening on
side opposite JUNCTION BOX. Push REFLECTOR up leaving
approximately one inch of the REFLE~R exposed below the
CEILING LINE (Fia. 10A).
LENS WALL WASHER
SOCKET CUP
r JUNCTION
BOX
REFL LEAVE APPROX.
1“ EXPOSED
TITE
G
M
2.
Compress TORSl~NTITE SPRINGS on LENS TRIM by squeezing
\
with fingem. Insert into SLOTS in
REFLECTOR and push up into
REFLECTOR until flush with ceiling (Fig. 11).
NOTE To remove REFLEC70R, lift LENS and pull LENS TRIM down
u“
WALL TO BE ILLUMINATED
(Fig. 12), then disengage the SOCKET CUP by daprsssing the
RETAINING SPRING (Fig.5). lhrn REFLECTOR counterclockwise
while pulling downward. Aftar stafling, use both hands to remove.
See Fig. 7.
FIG. 10A
PUSH-UP REFLECTOR FOR OPEN WALL WASHER
1,Tilt
REFLECTOR and insert SOCKET CUP into ceiling opening on
OPEN WALL WASHER
side opposite JUNCTION BOX. Pivot REFLECTOR and push it up
into ceilina [Fia. 13).
-.-,
NOTE To remove REFLECTOR, disengage the SOCK~ CUP by
daprassing the RETAINING SPRING (Fig. 5). 7urn REFLEC70R
counteroiockwise while pulling downward. After starting, use
both hands to remove If dasired. Saa Fig. 7.
*K
~ b
JUNCTION
BOX
7
D. LAMPING
Line up pins and push into socket. To relamp, carefully pull lamp
straight out.
CARE AND MAINTENANCE OF A12AK@ REFLECIOR
If handling of reflectors with anodized or Alzak finish is required, the
use of clean white or plastic film gloves is recommended to avoid
fingerprints.
Anodized or Alzak surfaces can be cleaned by the following methods
1.
2.
3.
4.
Wipe off with a soft, clean, dry, lint-free cloth.
Wipe off with a soft clean cloth dampened
in mild detergent
solution. Rinse then wipe dry with lint-free cloth or paper towel.
Wipe off with a clean cloth dampened with a solution of wetting
agent and water (such as 2 oz. per gallon “Pluronic L62-LF” by
Wyandotte Products). Then wipe dry.
Or use a liquid wash such as Glass Wax”. Avoid gritty cleaning
agents.
/-- ‘“’%lON
SOCKET
CUP
-Qi-REFLEcTOR
--
WALL TO BE ILLUMINATED
FIG. 10B
FIG. 11
FIG.
13
FIG.
12
/
