Hikvision ADS-24S-12 1224GPCN Quick start guide

Video Intercom Main Unit

Quick Start Guide

Scan to get detailed User Manual

Video Intercom Main Unit·Quick Start Guide

ii

Quick Start Guide

This quick start guide is intended for users of main unit(DS-KD8003-IME1).

Main unit is an important component of module door station. It can work both alone

and together with other function modules.

It includes instructions on how to use the Product. The software embodied in the

Product is governed by the user license agreement covering that Product.

About this Manual

This Manual is subject to domestic and international copyright protection. Hangzhou

Hikvision Digital Technology Co., Ltd. (“Hikvision”) reserves all rights to this manual. This

manual cannot be reproduced, changed, translated, or distributed, partially or wholly,

by any means, without the prior written permission of Hikvision.

Trademarks

and other Hikvision marks are the property of Hikvision and are

registered trademarks or the subject of applications for the same by Hikvision and/or its

affiliates. Other trademarks mentioned in this manual are the properties of their

respective owners. No right of license is given to use such trademarks without express

permission.

Disclaimer

TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, HIKVISION MAKES NO WARRANTIES,

EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES OF

MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, REGARDING THIS MANUAL.

HIKVISION DOES NOT WARRANT, GUARANTEE, OR MAKE ANY REPRESENTATIONS REGARDING THE

USE OF THE MANUAL, OR THE CORRECTNESS, ACCURACY, OR RELIABILITY OF INFORMATION

CONTAINED HEREIN. YOUR USE OF THIS MANUAL AND ANY RELIANCE ON THIS MANUAL SHALL BE

WHOLLY AT YOUR OWN RISK AND RESPONSIBILITY.

TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, IN NO EVENT WILL HIKVISION, ITS

DIRECTORS, OFFICERS, EMPLOYEES, OR AGENTS BE LIABLE TO YOU FOR ANY SPECIAL,

CONSEQUENTIAL, INCIDENTAL, OR INDIRECT DAMAGES, INCLUDING, AMONG OTHERS, DAMAGES

FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, SECURITY BREACHES, OR LOSS OF DATA

OR DOCUMENTATION, IN CONNECTION WITH THE USE OF OR RELIANCE ON THIS MANUAL, EVEN IF

HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY OR CERTAIN

DAMAGES, SO SOME OR ALL OF THE ABOVE EXCLUSIONS OR LIMITATIONS MAY NOT APPLY TO YOU.

Video Intercom Main Unit·Quick Start Guide

iii

Support

Should you have any questions, please do not hesitate to contact your local dealer.

Video Intercom Main Unit·Quick Start Guide

iv

Regulatory Information

FCC Information

Please take attention that changes or modification not expressly approved by the party

responsible for compliance could void the user’s authority to operate the equipment.

FCC compliance: This equipment has been tested and found to comply with the limits

for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio frequency energy and,

if not installed and used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the interference by one

or more of the following measures:

—Reorient or relocate the receiving antenna.

—Increase the separation between the equipment and receiver.

—Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

—Consult the dealer or an experienced radio/TV technician for help.

FCC Conditions

This device complies with part 15 of the FCC Rules. Operation is subject to the following

two conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including interference that may

cause undesired operation.

EU Conformity Statement

This product and - if applicable - the supplied accessories too are

marked with "CE" and comply therefore with the applicable

harmonized European standards listed under the EMC Directive

2014/30/EU, LVD Directive 2014/35/EU, the RoHS Directive

2011/65/EU.

2012/19/EU (WEEE directive): Products marked with this symbol

cannot be disposed of as unsorted municipal waste in the European

Union. For proper recycling, return this product to your local supplier

upon the purchase of equivalent new equipment, or dispose of it at

designated collection points. For more information see:

www.recyclethis.info

Video Intercom Main Unit·Quick Start Guide

v

2006/66/EC (battery directive): This product contains a battery that

cannot be disposed of as unsorted municipal waste in the European

Union. See the product documentation for specific battery

information. The battery is marked with this symbol, which may

include lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg).

For proper recycling, return the battery to your supplier or to a

designated collection point. For more information see:

www.recyclethis.info

Video Intercom Main Unit·Quick Start Guide

vi

Safety Instruction

These instructions are intended to ensure that user can use the product correctly to

avoid danger or property loss.

The precaution measure is divided into Warnings and Cautions:

Warnings: Neglecting any of the warnings may cause serious injury or death.

Cautions: Neglecting any of the cautions may cause injury or equipment damage.

Warnings

 The working temperature of the device is from -40º C to 60º C.

 All the electronic operation should be strictly compliance with the electrical safety

regulations, fire prevention regulations and other related regulations in your local

region.

 Please use the power adapter, which is provided by normal company. The power

consumption cannot be less than the required value.

 Do not connect several devices to one power adapter as adapter overload may cause

over-heat or fire hazard.

 Please make sure that the power has been disconnected before you wire, install or

dismantle the device.

 When the product is installed on wall or ceiling, the device shall be firmly fixed.

 If smoke, odors or noise rise from the device, turn off the power at once and unplug

the power cable, and then please contact the service center.

 If the product does not work properly, please contact your dealer or the nearest

service center. Never attempt to disassemble the device yourself. (We shall not

assume any responsibility for problems caused by unauthorized repair or

maintenance.)

 The power supply must conform to LPS. The recommended adaptor models and

manufacturers are shown as below. Use the attached adaptor, and do not change the

adaptor randomly.

Model

Manufacturer

Standard

ADS-24S-12 1224GPCN

Shenzhen Honor Electronic

Co., Ltd.

GB

KPL-060F-VI

Channel Well Technology

Co., Ltd.

GB

Warnings Follow

these safeguards to

prevent serious

injury or death.

Cautions Follow these

precautions to prevent

potential injury or

material damage.

Video Intercom Main Unit·Quick Start Guide

vii

Cautions

 Do not drop the device or subject it to physical shock, and do not expose it to high

electromagnetism radiation. Avoid the equipment installation on vibrations surface or

places subject to shock (ignorance can cause equipment damage).

 Do not place the device in extremely hot (refer to the specification of the device for

the detailed operating temperature), cold, dusty or damp locations, and do not

expose it to high electromagnetic radiation.

 Do not aim the device at the sun or extra bright places. A blooming or smear may

occur otherwise (which is not a malfunction however), and affecting the endurance of

sensor at the same time.

 Please use a soft and dry cloth when clean inside and outside surfaces of the device

cover, do not use alkaline detergents.

 Please keep all wrappers after unpack them for future use. In case of any failure

occurred, you need to return the device to the factory with the original wrapper.

Transportation without the original wrapper may result in damage on the device and

lead to additional costs.

 Improper use or replacement of the battery may result in hazard of explosion.

Replace with the same or equivalent type only. Dispose of used batteries according to

the instructions provided by the battery manufacturer.

 The warranty does not apply to the product defects and failures arisen as a result of

improper mounting (in contradiction herewith).

 When the proper mounting instructions are not met, water might get in and destroy

the electronics.

   
Video Intercom Main Unit·Quick Start Guide 
viii 
 
Table of Contents 
Appearance .................................................................................................. 1 
Terminal and Wiring ..................................................................................... 2 
1 Terminal Description ................................................................................................ 2 
2 Wiring Description ................................................................................................... 3 
2.1 Door Lock Wiring ............................................................................................... 3 
2.2 Door Magnetic Wiring ....................................................................................... 4 
2.3 Exit Button Wiring ............................................................................................. 4 
Installation ................................................................................................... 6 
1 Configure Sub Module Address ............................................................................... 6 
2 One-Module Installation .......................................................................................... 7 
2.1 One-Module Surface Mounting ........................................................................ 7 
2.2 One-Module Flush Mounting .......................................................................... 11 
3 Two-Module Installation ........................................................................................ 15 
3.1 Two-Module Surface Mounting ...................................................................... 15 
3.2 Two-Module Flush Mounting .......................................................................... 20 
4 Three-Module Installation ..................................................................................... 25 
4.1 Three-Module Surface Mounting .................................................................... 25 
4.2 Three-Module Flush Mounting ....................................................................... 30 
5 More-than-Three Module Installation ................................................................... 36 
5.1 More-than-Three Module Surface Mounting .................................................. 36 
5.2 More-than-Three Module Flush Mounting ..................................................... 42 
Remote Operation ...................................................................................... 51 
1 Activate Device ...................................................................................................... 51 
2 Edit Network Parameters ....................................................................................... 52 
3 Add Device ............................................................................................................. 53 
4 Call Resident .......................................................................................................... 54 
4.1 Dial via Main Unit ............................................................................................ 54 
4.2 Dial via Nametag Module ................................................................................ 55 

Video Intercom Main Unit·Quick Start Guide

1

1 Appearance

Figure 1-1 Main Unit Appearance

Table 1-1 Appearance Description

No.

Description

1

Microphone

2

Low Illumination IR Supplement Light

3

Built-in Camera

4

Loudspeaker

5

Call Button

6

Nametag

7

TAMPER

8

Network Interface

9

Module-connecting Interface(output)

10

Terminals

 Nametag area supports insert customized name card.

The suggested card size is: 58 (L) x 11.7(W) mm.

 The module connecting interface is used to connect other function module, such as

nametag module, keypad module, card reader module, etc. All these modules are

known as sub module.

Video Intercom Main Unit·Quick Start Guide

2

2 Terminal and Wiring

2.1 Terminal Description

Figure 2-1 Terminals and Interfaces

Table 2-1 Descriptions of Terminals and Interfaces

No.

Interface

Description

A1

NC1

Door Lock Relay Output (NC)

A2

NO1

Door Lock Relay Output (NO)

A3

COM

Common Interface

A4

NC2

Door Lock Relay Output (NC)

A5

NO2

Door Lock Relay Output (NO)

A6

GND

Grounding

A7

12V DC

Power Supply Output

A8

GND

Grounding

B1

AIN2

For the access of Door Magnetic2

B2

AIN1

For the access of Door Magnetic1

B3

AIN3

For the access of Exit Button 1

B4

AIN4

For the access of Exit Button 2

B5

485-

Module-connecting Interface

B6

485+

Video Intercom Main Unit·Quick Start Guide

3

No.

Interface

Description

B7

12V OUT

B8

GND

C

LAN

PoE Network Interface(Supports IEEE

802.3af/at-Compliant Devices)

2.2 Wiring Description

2.2.1 Door Lock Wiring

Figure 2-2 Door Lock Wiring

 Terminal NC1/COM is set as default for accessing magnetic lock/electric bolt; terminal

NO2/COM is set as default for accessing electric strike.

 Lock should be powered by itself. Max. voltage and current for relay is 30V and 1A.

Video Intercom Main Unit·Quick Start Guide

4

2.2.2 Door Magnetic Wiring

Figure 2-3 Door Magnetic Wiring

AIN1 and AIN2 are defaulted to connect door magnetic. Door magnetic connected to

AIN1 detects status of the lock that connected to NC1/NO1; Door magnetic connected

to AIN2 detects the status of the lock connected to NC2/NO2.

2.2.3 Exit Button Wiring

Figure 2-4 Exit Button Wiring

Video Intercom Main Unit·Quick Start Guide

5

AIN3 and AIN4 are set as default for connecting exit button. Exit button connected to

AIN3 opens the lock connected to NC1/NO1; Exit button connected to AIN4 controls the

lock that connected to NC2/NO2.

Video Intercom Main Unit·Quick Start Guide

6

3 Installation

Before you start:

 Make sure the device in the package is in good condition and all the assembly parts

are included.

 Sub module must work along with the main unit.

 Set the sub module address before start the installation steps.

 Make sure the place for surface mounting is flat.

 Make sure all the related equipment is power-off during the installation.

 Tools that you need to prepare for installation:

Drill (ø6), cross screwdriver (PH1*150 mm), and gradienter.

 Buy corresponding accessory package for installation. The accessory package model

and its suitable installation method as below:

Package

Model

Mounting Method

Note

DS-KD-ACW1

One-Module Surface Mounting

Install the device according

to the instructions.

Not all the lines in the

accessory package will be

used.

DS-KD-ACW2

Two-Module Surface Mounting

DS-KD-ACW3

Three-Module Surface Mounting

DS-KD-ACF1

One-Module Flush Mounting

DS-KD-ACF2

Two-Module Flush Mounting

DS-KD-ACF3

Three-Module Flush Mounting

3.1 Configure Sub Module Address

You need to set the sub module address via DIP before installation.

Steps:

1. Remove the rubber cover on the sub module rear panel to expose the DIP switch.

Video Intercom Main Unit·Quick Start Guide

7

Figure 3-1 DIP Switch

2. Set the sub module address according to the DIP rules, and install the rubber cover

back.

 Digit 1, 2, 3, 4 are used to coding the sub module address; Digit 5, 6, 7 are reserved;

Digit 8 is a resistance (120Ω) is you set it as on.

 Valid sub module address range is 1 to 8. The No. should be unique for sub modules

that connected to the same main unit.

The sub module address and corresponding switch status as below.

Sub Module

Address

1

2

3

4

.5

6

7

8

Digit 1

ON

OFF

ON

OFF

ON

OFF

ON

OFF

Digit 2

OFF

ON

OFF

ON

OFF

Digit 3

OFF

ON

OFF

Digit 4

OFF

ON

3.2 One-Module Installation

3.2.1 One-Module Surface Mounting

Mounting Frame

Video Intercom Main Unit·Quick Start Guide

8

Figure 3-2 Front and Side View

 The dimension of one module mounting frame is: 117(L)×107(W)×32.7(D) mm.

 The dimensions above are for reference only. The actual size can be slightly different

from the theoretical dimension.

Steps:

1. Paste the installation Sticker 1 onto the wall. Make sure the sticker is placed leveled

via measuring with the gradienter.

2. Chisel 4 holes with drill align to the screw holes on the sticker.

The suggested size of hole is 6 (diameter) × 25 (depth) mm.

The suggested length of cables left outside is 100 mm.

Video Intercom Main Unit·Quick Start Guide

9

Figure 3-3 Chisel Screw Hole

3. Remove the sticker and insert the expansion sleeves into the screw holes.

4. Fix the mounting frame onto the wall with 4 expansion bolts.

Video Intercom Main Unit·Quick Start Guide

10

Figure 3-4 Fix the Mounting Frame

 The mounting frame should be placed exactly as below for this step. The tamper plate

should be at the low-right.

5. Connect the cables to the corresponding interfaces of the main unit and insert it into

the frame.

Video Intercom Main Unit·Quick Start Guide

11

Figure 3-5 Insert the Main unit

6. Use the hexagon wrench in the package fix the cover onto the frame.

Figure 3-6 Fix the Cover

3.2.2 One-Module Flush Mounting

Gang Box

Video Intercom Main Unit·Quick Start Guide

12

Figure 3-7 Front and Side View

Figure 3-8 Appearance Description

Page is loading ...

Hikvision ADS-24S-12 1224GPCN, KPL-060F-VI Quick start guide

Related papers

Other documents