Bennett Marine BCN6000 Installation guide

Bennett Marine
Brand
Bennett Marine
Model
BCN6000
Category
Motorcycle Accessories
Type
Installation guide

Bennett Marine BCN6000 is a state-of-the-art BOLT Control system designed to provide precise and reliable trim tab control for your boat. With its intuitive interface and advanced features, the BCN6000 empowers you to optimize your boat's performance and enhance your on-water experience.

Key capabilities of the BCN6000 include:

  • Intuitive helm display with clear and concise indicators for effortless trim tab adjustment
  • Auto Tab Retraction (ATR) feature automatically retracts trim tabs when the ignition is turned off, ensuring a smooth and efficient transition to trailering or storage
  • Diagnostics Relay Module continuously monitors system performance and provides alerts in case of any irregularities, giving you peace of mind on the water

Bennett Marine BCN6000 is a state-of-the-art BOLT Control system designed to provide precise and reliable trim tab control for your boat. With its intuitive interface and advanced features, the BCN6000 empowers you to optimize your boat's performance and enhance your on-water experience.

Key capabilities of the BCN6000 include:

  • Intuitive helm display with clear and concise indicators for effortless trim tab adjustment
  • Auto Tab Retraction (ATR) feature automatically retracts trim tabs when the ignition is turned off, ensuring a smooth and efficient transition to trailering or storage
  • Diagnostics Relay Module continuously monitors system performance and provides alerts in case of any irregularities, giving you peace of mind on the water
User Quick-start Guide
BCN Control Installation Instructions
• Before drilling any holes, read the entire instructions.
• Using the included template (below), mark the locations for
the 3/16" holes and the 1" center hole.
• Check carefully to ensure there are no obstructions behind
the console before drilling any holes.
• Using a 1" diameter hole-saw, drill the center hole. Use a
3/16" drill for the four mounting stud holes.
• Place the helm display keypad onto the console, feeding
the pre-connected wires through the 1" center hole while
inserting the screws into each of the four holes.
• Once the control plate is properly seated, use the 4 white
nylon thumb nuts provided to secure the display.
• Plug the 3 ft. wire harness on the display to the 3 ft. wire
harness on the BCN Diagnostics Relay Module (If cable
length is not long enough, an extension is available as part
number BHW40XX).
• Connect the orange wire to the power source for the gauges
at the helm. is will power the control with all other dash
devices.
• Connect the purple wire to the ignition switch (or any 12V
circuit that turns ON and OFF with ignition) for auto tab
retraction. is wire is used to initiate Auto Tab Retraction
(ATR) when the ignition is switched to the OFF position. If
ATR is not desired, this connection may be omitted.
Diagnostics Relay Module Installation
• Mount the Diagnostics Relay Module under the helm using
the mounting hardware (2 screws provided) to secure it
in place.
• Plug the (2) wire harnesses (BAW20XX) into the port and
starboard actuators at one end. en plug the other end of
the (2) wire harnesses (BAW20XX) to the port and starboard
plugs on the Diagnostics Relay Module (If cable length is not
long enough, an extension is available).
• Find a suitable dry location
• Mount using #8 x 1/2" screws
• Connect helm control
• Plug the port yellow/blue 20ft. twisted cable
(PN# BAW20XX) to the port connector on the BRC Rocker
Control.
• Plug the starboard yellow/blue 20ft. twisted cable
(PN# BAW20XX) to the starboard connector on the BRC
Rocker Control.
• Connect ground (black wire) to ground bus
• Connect power (orange wire) to a supply capable of a 20A
(12V), or 10A (24V)
• Control will power up when the orange wire is connected
• If the system is not functioning properly, refer to the
troubleshooting section on the reverse side.
BOLT Control (BCN6000) Installation & Quick-start Instructions
BCI or BCN Control Templates
Both templates on this page are identical. The second has been provided for dual station applications.
Must be printed/copied at 100% scale 1"
3
—
16
"
1
"
13
—
16
2
"
13
—
16
2
"
1
—
8
2
"
1
—
8
2
"
3
—
16
"
1
"
13
—
16
2
"
13
—
16
2
"
1
—
8
2
"
1
—
8
2
"
For information on installing a complete BOLT Trim Tab System, please visit BennettTrimTabs.com/BOLT-Install
Raises
Port Bow
Lowers
Starboard Bow
Raises
Starboard
Bow
Lowers
Port Bow
BCN Control Installation Drilling Templates
Both drilling templates below are identical. e second has been provided for dual station applications. Must be copied at 100% if replicated.
Verify template dimensions if
printed from the web or copied
Helm Display
BCN6700
Green Communications LED
Red Power LED
Starboard actuator up
(yellow), down (blue)
Port actuator up (yellow),
down (blue)
BCN6500
Verify template dimensions if
printed from the web or copied
BOLT Trim Tab System Wiring Diagram with BCN Control
ORANGE WIRE
CONNECT TO HELM POWER
PURPLE WIRE
CONNECT TO IGNITION POWER
GROUND
1
2
3
4
5
ORANGE WIRE
CONNECT TO 20A,(12V)
10A, (24V)
No.
PART NAME
SPEC SHEET
1
BQEACT-XX
BOLT
2
BQEMTREXTCABLE-X
Wire Harness
3
BQERM-XX
BQE
4
BQEDISPEXTCABLE-X
Wire Harness
5
BQEDISPLAY
BQE
HARDWARE KITS
PART NUMBER
DESCRIPTION
QTY REQ.
UPPER HINGE
HDWBQEUHF
Fixed Upper Hinge
1
HDWBQEUHB
Bennett Adjustable Upper Hinge
1
HDWBQEUHL
Lenco Adjustable Upper Hinge
1
LOWER HINGE
HDWBQELHB
Bennett Lower Hinge
1
HDWBQELHR
Rivet Clearance Lower Hinge
1
HDWBQELHL
Lenco Lower Hinge
1
CONNECTORS
HDWWPC16PLG2
Waterproof Connector Plugs
1
D
C
B
A
A
B
C
D
1
2
3
4
5
6
7
8
8
7
6
5
4
3
2
1
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
Bennett Marine Inc. ANY REPRODUCTION
IN PART OR AS A WHOLE WITHOUT THE
WRITTEN PERMISSION OF
Bennett Marine Inc IS PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
NEXT ASSY
USED ON
APPLICATION
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
1/16
ANGULAR: MACH
BEND
TWO PLACE DECIMAL
.01
THREE PLACE DECIMAL
.005
INTERPRET GEOMETRIC
TOLERANCING PER: ANSI Y-14
MATERIAL
FINISH
DRAWN
CHECKED
ENG APPR.
MFG APPR.
Q.A.
COMMENTS:
DATE
NAME
TITLE:
SIZE
B
DWG. NO.
REV
WEIGHT:
SCALE: 1:8
UNLESS OTHERWISE SPECIFIED:
SHEET 1 OF 4
BQE
Single/Single
DO NOT SCALE DRAWING
Bennett Marine
550 Jim Moran Blvd
Deerfield Beach, FL 33442
DOWN DOW N
UPUP
Have questions?
For information on installing a complete BOLT Trim Tab System, please visit BennettTrimTabs.com/BOLT-Install
1. Actuators
2. Diagnostics Relay Module
Extension Cable
3. Relay Module
4. Display Extension Cable
5. Helm Display
For dual station or dual actuator wiring
diagrams please visit
BennettTrimTabs.com/BOLT-Install
BQE123 r031406
We’re here to help.
For product support, please call 1-866-894-1626 (Option #3), or email BMI_Info@Yamaha-motor.com.
Bennett Marine is a Division of Yamaha Marne Systems Company, Inc. – Learn more at BennettTrimTabs.com
  • Page 1 1
  • Page 2 2

Bennett Marine BCN6000 Installation guide

Bennett Marine
Brand
Bennett Marine
Model
BCN6000
Category
Motorcycle Accessories
Type
Installation guide

Bennett Marine BCN6000 is a state-of-the-art BOLT Control system designed to provide precise and reliable trim tab control for your boat. With its intuitive interface and advanced features, the BCN6000 empowers you to optimize your boat's performance and enhance your on-water experience.

Key capabilities of the BCN6000 include:

  • Intuitive helm display with clear and concise indicators for effortless trim tab adjustment
  • Auto Tab Retraction (ATR) feature automatically retracts trim tabs when the ignition is turned off, ensuring a smooth and efficient transition to trailering or storage
  • Diagnostics Relay Module continuously monitors system performance and provides alerts in case of any irregularities, giving you peace of mind on the water
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents