Fibaro FGBHFS-101 User manual

FGBHFS-101
Fibaro
Brand
Fibaro
Model
FGBHFS-101
Type
User manual

This manual is also suitable for

INSTRUCTION MANUAL
FIBARO SYSTEM
FLOOD SENSOR
Technical support
Should youneed any assistance in connecting or configuring your Home Center, please use our guides
and technical presentations which can be found on our website:
http://www.baro.com/en/support
Flood sensor Temperature sensor
Functional features
Tilt sensorSignal and
light alarm
Download FIBARO app for smartphone
Start the device
Twist and open the casing.
STEP 1
Take off the casing.
STEP 2
B
ee
p
!
Remove the battery blocker
“I’m ready”.
STEP 3
Start the device
You will hear a beep while LED
diode blinks red.
Check if the battery
is placed correctly.
STEP 4
Your Flood Sensor is ready to be added to
the Home Center.
Flood Sensormust be in range of the Home Center because it requires
a direct communication with the controller.
Start inclusion mode
Start your FIBARO application.
Go to Settings.
STEP 5
Start inclusion mode
STEP 7
STEP 6
Press “Next”.
Press “add device”.
Inclusion mode has been launched
Add your device
Quickly, triple click the button in order
to add your device to the system.
STEP 8
Processing your congurations
Quickly, triple click the button
in order to wake up the device.
STEP 9
Wake up the device
Sometimes waking up the device is not required
so it will be omitted automatically.
The device has been added
Name the device
and assign it to the room.
STEP 10
STEP 11
Hold the button for about 10-15 seconds
until LED diode blinks violet.
STEP 12
Release the button, and press it again.
Network range test
It is recommended to check if the device’s destination
is in range of your Home Center.
The quality of the network range will be
indicated by different colours
of the LED diode.
Network range test – quality indicator
Direct
communication
Routed
communication
Limited
communication
No signal! The device
will not work correctly!
Press the button in order to
leave testing mode.
STEP 13
Close and twist the cover.
STEP 14
Close the casing
Installation
1. FIBARO Flood Sensor should be installed in all
spaces, where’s the risk of flood:
• In the bathroom,
• In the kitchen,
• At the basement.
3. A built-in temperature sensor lets you
monitor e.g. floor’s temperature.
2. Additional security informs about accidental
location change (every time it changes its location
in information is being sent to Home Center).
During the installation it is recommended to wake up the device.
Adding a probe
If the sensor cannot fit the space which is in danger of flooding
you can install a wired probe* that will get to difficult
to access spaces.
*The probe is not included in the
Flood Sensor set.
Here install the probe
www.fibaro.com
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20

Fibaro FGBHFS-101 User manual

FGBHFS-101
Fibaro
Brand
Fibaro
Model
FGBHFS-101
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers