Setting the week plan
In a ring around the clock you’ll find
the seven days of the week, divided
into one-hour segments.
Decide when you want comfort or
setback temperature for each day, and
position the sliders accordingly:
For comfort temperature, the sliders
point towards the centre; for setback
temperature, they point out.
ECL Comfort 100C quick guide
Remove tape on the back.
Position on inside of the
ECL Comfort cover.
*087R9764*
*vikmb102*
ECL Comfort 100C
VI.KM.B1.02
2005.03
Clock and scheduleClock and schedule
ECL Comfort 100C quick guide
Remove tape on the back.
Position on inside of the
ECL Comfort cover.
*087R9764*
*vikmb102*
ECL Comfort 100C
VI.KM.B1.02
2005.03
Setting the week plan
In a ring around the clock you’ll find
the seven days of the week, divided
into one-hour segments.
Decide when you want comfort or
setback temperature for each day, and
position the sliders accordingly:
For comfort temperature, the sliders
point towards the centre; for setback
temperature, they point out.
Temperature setting
Heat curve
displacement or
room temperature
(if room sensor
is installed:
Range 12–28 °C,
“0” is 20 °C
0
+8
-8
Mode selector
Manual operation
Comfort temperature
Scheduled
Setback temperature
Standby
Temperature setting
Heat curve
displacement or
room temperature
(if room sensor
is installed:
Range 12–28 °C,
“0” is 20 °C
0
+8
-8
Mode selector
Manual operation
Comfort temperature
Scheduled
Setback temperature
Standby
Setting the clock
Week day Minute hand
1
8
1
2
6
1
8
1
2
6
1
8
1
2
6
1
8
1
2
6
1
8
1
2
6
1
8
1
2
6
1
8
1
2
6
12
3
6
9
White arrow Sliders
Turn the minute hand until the white
arrow points to the current week day
and hour in the outer ring. Do not turn
the outer ring itself.
Please note!
Do not turn anti-clockwise!
Setting the clock
Week day Minute hand
1
8
1
2
6
1
8
1
2
6
1
8
1
2
6
1
8
1
2
6
1
8
1
2
6
1
8
1
2
6
1
8
1
2
6
12
3
6
9
White arrow Sliders
Turn the minute hand until the white
arrow points to the current week day
and hour in the outer ring. Do not turn
the outer ring itself.
Please note!
Do not turn anti-clockwise!
XXXXXXXXXXX
ECL Comfort 100C
Temperature Heat curve
reduction slope
You can choose how many degrees
below comfort temperature you want
the room temperature to be reduced,
during time periods with setback
temperature.
Battery holder Heat curve slope
-20 -10 0 10 20-30
20
30
40
50
60
1.2
0.6
0.2
1.8 2.2
10
o
C
o
C
You can set the heat curve slope in a
range from 0.2 to 2.2.
Note:
The slope is factory-set to 1.2.
Battery holder Heat curve slope
-20 -10 0 10 20-30
20
30
40
50
60
1.2
0.6
0.2
1.8 2.2
10
o
C
o
C
You can set the heat curve slope in a
range from 0.2 to 2.2.
Note:
The slope is factory-set to 1.2.
ECL Comfort 100C
Temperature Heat curve
reduction slope
You can choose how many degrees
below comfort temperature you want
the room temperature to be reduced,
during time periods with setback
temperature.
Power back-up for the analog clock
To ensure power back-up, there is a
battery placed above the clock. This
battery is normally not in use, but it
is recommended that you replace it
every two years. Use an Alcaline AAA
1.5 V type.
Installation date:
Date replaced:
1
2
3
4
5
6
7
8
Power back-up for the analog clock
To ensure power back-up, there is a
battery placed above the clock. This
battery is normally not in use, but it
is recommended that you replace it
every two years. Use an Alcaline AAA
1.5 V type.
Installation date:
Date replaced:
1
2
3
4
5
6
7
8
Service settingsService settings
-
1
-
2
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Danfoss ECL Comfort 100C Operating instructions
-
-
-
-
-
-
-
-
-