2. RTS
  3. Oki - kp 32

RTS Oki - kp 32 User manual

  • Hello! I am an AI chatbot trained to assist you with the RTS Oki - kp 32 User manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
Quick Start Guide
OKI - OMNEO Keypanel Interface KP-32 Classic
Included:
• OMNEOKeypanelModule
• Rearpanel,OKIoption,KP-32Classic
• 3-Screw,4-40x.25LG
• QuickStartGuide,KP-32
• OKIDocumentationResourceDisk
• WarrantyCard
• SafetyInstructionsST-CO
Requirements:
Youmusthavethefollowing:
• PhillipsScrewdriver
• HexDriver(2sizes–4-40and6-32)
Firmware Requirements
• KP-32ClassicFirmwareversion2.4.0
• KP-32BootLoaderversion0.1.0
IMPORTANT Thekeypanelbootloadermustbedone
beforethermwareisupdated.And,the
rmwaremustbeupgradedbeforeyouinstall
theOKImoduleintothekeypanel.
OKI Installation – KP-32 Classic
Important: Verifyyouhaveupdatedthebootloader
ontheKP-32Classickeypanelbefore
addingtheOKImodule.(seeBootloader
Upgradeonback).
Toinstall the OKI board set for the KP-32 Classic
keypanel,dothefollowing:
1. PowerofftheKP-32Classickeypanel.
2. UsingaPhillipsscrewdriver,removethefour (4)
corner screwsfromthebackpanel.
Note: Steps3and4areonlynecessaryifyouhavean
RCoptioninstalled.
3. Usingahexnutdriver,removethe14 hex screws
fromthebackpanel.
4. Usingthesamescrewdriver,removetheeight (8)
pan head screwsfrombackpanel.
5. UsingaPhillipsscrewdriver,removethe13 at
head screwsfrom top,bottomandbackpanel.
F01U273975Rev04 07/2014
Quick Start Guide
OKI - OMNEO Keypanel Interface KP-32 Classic
6. CarefullyattachtheOKI board set J1 to the
KP-32 Classic main board J4,asshownbelow.
Important: TheOKIboardsetafxestothechassis
insteadofthemotherboard.Ensureall
connectorsareushtothechassisbefore
replacingthescrews.
7. Carefullyreplacetheback panelontheKP-32
Classic.
8. Usethetwo (2) pan head screws provided to
stabilize the OKI board to the chassis.
NOTE: Steps10and11areonlynecessaryifyouhave
anRCoptioninstalled.
9. Replacethe14 hex screws.
10. Replacetheeight (8) pan head screws.
11. Replacethe10 at head screws.
12. Replacethe four (4) corner pan head screwsthat
attachthebackpanel.
13. PowerontheKP 32 CLD.
NOTE: IfyouarenotusinganRCcard,usetheRC
covertocovertheRCplateholes.
Upgrade the KP-32 Boot Loader Version to
version V0.1.0
Important: Thisupgrademustbedonebefore
upgradingthermwareoftheKP-32unit.
Toupgrade the KP-32 Boot Loader,dothefollowing:
1. OnthebackpaneloftheKP-32keypanel,turnDIP
switch 8 On.
2. Power on theunit.
A message indicating “This panel needs a rmware
download” appears.
3. InAZedit,fromtheStatusmenu,selectSoftware
Versions.
The Software Versions popup menu appears.
4. FromtheSoftwareVersionspopupmenu,select
Keypanels.
The Keypanel Version Information window appears.
5. FromtheKeypanelVersionInformationwindow,nd
andselectthespecic KP-32.
NOTE:NoticetheVersioncolumnisthemessage
“NEEDSDOWNLOAD”appearsnexttothe
versionstringofthekeypanel.
6. Right-clickKP-32 versionyouwanttoupgrade.
A popup menu appears.
7. Fromthepopupmenu,selectDownload
Firmware....
The Firmware Download navigation window
appears.
8. Navigatetoandselectyourrmware le(i.e.,
KP32CLD.hex).
9. ClickOpen.
The Download Device Firmware window appears.
10. ClickBegin Download.
The Download begins and a popup message
appears.
11. ClickOK.
The KP-32 rmware download nishes.
NOTE:Thiscantakeupto30minutestocomplete.Use
theKeypanelVersionInformationwindowto
followtheprogressofthedownload(thenumber
andpercentageofchunkscompleted).Also,the
rmwareprogressionisdisplayedontheKP-32
displaywindowuntilthedownloadiscomplete.
12. OnthebackpaneloftheKP-32keypanel,turnDIP
switch 8 Off.
13. Power cycletheunit.
Important: Thekeypanelrmwaremustbeupdated
beforeyouinstalltheOKImoduleintothe
keypanel.
For the most current user documentation,
rmware, and software, visit
www.rtsintercoms.com.
/