RTS Oki - kp 32 cld User manual

RTS
Brand
RTS
Model
Oki - kp 32 cld
Type
User manual

This manual is also suitable for

Quick Start Guide
OKI - OMNEO Keypanel Interface KP 12 CLD
Included:
• OMNEOKeypanelModule
• RearPanel,KP12CLD,Expansion
• 2-Screw,4-40x.25LG.
• 3-Screw,PH,4-40x3/16LG.
• SafetyInstructionsST-CO
• OKIQuickStartGuide
• OKIDocumentationResourceDisk
Requirements:
Youmusthavethefollowing:
• PhillipsScrewdriver
• HexNutDriver
Firmware Requirements
• KP12CLDversion1.30
IMPORTANT Thekeypanelrmwaremustbeupdatedbefore
youinstalltheOKImoduleintothekeypanel.
Reference View - OKI KP 12 CLD
Description
1.J1&J2 RJ-45Connectors(2)
2.J3 LCFiberConnector(Optional)
OKI Installation – KP 12 CLD
Toinstall the OKI board set for the KP 12 CLD,dothe
following:
NOTE:Becauseallthechangesaremadetothe
expansionbox,removetheexpansionboxfrom
theKP12CLDunit.
1. PowerofftheKP12CLDunit.
2. Removetheexpansion boxfromtheKP12CLD
unit.
NOTE:Steps3and4areonlynecessaryifanRCoption
isinstalled.
3. Usingahexnutdriver,removethe12 hex screws
fromtheKP12CLDexpansionbox.
4. Usingthesamescrewdriver,removetheeight (8)
pan head screwsfromtheKP12CLDexpansion
box.
5. UsingaPhillipsscrewdriver,removethesix (6) at
head screwsfrom KP12CLDexpansionbox.
F01U280811Rev01 01/2013
Quick Start Guide
OKI - OMNEO Keypanel Interface KP 12 CLD
6. RemovetheKP 12 CLD expansion box cover.
7. Ifinstalled,removetheRVON standoffs.
8. Replacethestandoffswiththeprovidedpan head
screws (3).
Caution: EnsurethatallRJ-45connectorsonthe
boardareushwiththechassisopenings.
9. Usingtheprovidedpanheadscrews(2),secure
theOKI board set to the OKI KP 12 CLD
expansion box replacement cover.
NOTE:ItiseasiertoinstalltheOKIboardsettothe
OKIKP12CLDexpansionboxbackpanel
whiletheboardsetandthechassisarelaying
upsidedown,seepicturebelow.
NOTE: AligntheredstripeonthecablewithPin1.
10. Attachone end of the provided ribbon cable to
J2ontheOKIboardset.
11. Attachtheother end of the ribbon cable to J5
ontheKP12CLDexpansionboxmainboard.
12. Replacetheexisting cover with the OKI KP 12
CLD expansion box cover.
Caution: EnsurethatallRJ-45connectorsonthe
boardareushwiththechassisopenings.
13. Replacetheeight (8) pan head screws.
14. Replacethesix (6) at head screws.
15. Replacethe12 hex screws.
16. Usingtheexistingscrews,securetheOKI KP 12
CLD expansion box covertothechassis.
17. RemounttheKP 12 CLD expansion boxtothe
KP12CLDunit.
  • Page 1 1
  • Page 2 2

RTS Oki - kp 32 cld User manual

RTS
Brand
RTS
Model
Oki - kp 32 cld
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents