RTS Oki - kp 32 cld User manual

Brand: RTS

Model: Oki - kp 32 cld

Type: User manual

Quick Start Guide

OKI - OMNEO Keypanel Interface KP 12 CLD

Included:

• OMNEOKeypanelModule

• RearPanel,KP12CLD,Expansion

• 2-Screw,4-40x.25LG.

• 3-Screw,PH,4-40x3/16LG.

• SafetyInstructionsST-CO

• OKIQuickStartGuide

• OKIDocumentationResourceDisk

Requirements:

Youmusthavethefollowing:

• PhillipsScrewdriver

• HexNutDriver

Firmware Requirements

• KP12CLDversion1.30

IMPORTANT Thekeypanelrmwaremustbeupdatedbefore

youinstalltheOKImoduleintothekeypanel.

Reference View - OKI KP 12 CLD

Description

1.J1&J2 RJ-45Connectors(2)

2.J3 LCFiberConnector(Optional)

OKI Installation – KP 12 CLD

Toinstall the OKI board set for the KP 12 CLD,dothe

following:

NOTE:Becauseallthechangesaremadetothe

expansionbox,removetheexpansionboxfrom

theKP12CLDunit.

1. PowerofftheKP12CLDunit.

2. Removetheexpansion boxfromtheKP12CLD

unit.

NOTE:Steps3and4areonlynecessaryifanRCoption

isinstalled.

3. Usingahexnutdriver,removethe12 hex screws

fromtheKP12CLDexpansionbox.

4. Usingthesamescrewdriver,removetheeight (8)

pan head screwsfromtheKP12CLDexpansion

box.

5. UsingaPhillipsscrewdriver,removethesix (6) at

head screwsfrom KP12CLDexpansionbox.

F01U280811Rev02 01/2014

Quick Start Guide

OKI - OMNEO Keypanel Interface KP 12 CLD

6. RemovetheKP 12 CLD expansion box cover.

7. Ifinstalled,removetheRVON standoffs.

8. Replacethestandoffswiththeprovidedpan head

screws (3).

Caution: EnsurethatallRJ-45connectorsonthe

boardareushwiththechassisopenings.

9. Usingtheprovidedpanheadscrews(2),secure

theOKI board set to the OKI KP 12 CLD

expansion box replacement cover.

NOTE:ItiseasiertoinstalltheOKIboardsettothe

OKIKP12CLDexpansionboxbackpanel

whiletheboardsetandthechassisarelaying

upsidedown,seepicturebelow.

NOTE: AligntheredstripeonthecablewithPin1.

10. Attachone end of the provided ribbon cable to

J2ontheOKIboardset.

11. Attachtheother end of the ribbon cable to J5

ontheKP12CLDexpansionboxmainboard.

12. Replacetheexisting cover with the OKI KP 12

CLD expansion box cover.

Caution: EnsurethatallRJ-45connectorsonthe

boardareushwiththechassisopenings.

13. Replacetheeight (8) pan head screws.

14. Replacethesix (6) at head screws.

15. Replacethe12 hex screws.

16. Usingtheexistingscrews,securetheOKI KP 12

CLD expansion box covertothechassis.

17. RemounttheKP 12 CLD expansion boxtothe

KP12CLDunit.

RTS Oki - kp 32 cld User manual

RTS Oki - kp 32 cld User manual

RTS Oki - kp 32 cld User manual

Related papers

Other documents