Nordic POBA4750 is a powerful and versatile tool designed to make pruning and cutting tasks easier and more efficient. With its sturdy construction and sharp blades, it can effortlessly cut through branches up to 15 mm (hardwood) and 20 mm (softwood), making it ideal for maintaining your garden or orchard.
Nordic POBA4750 is a powerful and versatile tool designed to make pruning and cutting tasks easier and more efficient. With its sturdy construction and sharp blades, it can effortlessly cut through branches up to 15 mm (hardwood) and 20 mm (softwood), making it ideal for maintaining your garden or orchard.
OPERATING MANUAL
18V CORDLESS
BRANCH CUTTER
BC-L0118
2
NORDIC
PRODUCT SPECIFICATION
Voltage: 18V
Charger Voltage: 100-240V/50-60Hz
Max Cutting Dia: 28mm (fresh branch)
One-handed / Lightweight Design, Laser cut blade, Soft-grip handle
GENERAL POWER TOOL SAFETY WARNINGS
Read all safety warnings and instructions. Failure to heed warnings and follow instructions may result in
electric shock, fire and/or serious injury.
Keep safety warnings and instructions for future reference.
The term “power tool” in the safety warnings refers to your mains operated (corded) power tool or battery-
operated (cordless) power tool.
2.1 WORKING AREA
• Keep working area clean and well lit. Untidy and dark areas can lead to accidents.
• Do not operate power tools in potentially explosive surroundings, for example, in the presence of inflammable liquids,
gases or dust. Power tools create sparks which may ignite the dust or fumes.
• Keep children and bystanders at a distance when operating a power tool. Distractions can cause you to lose control of it.
2.2 ELECTRICAL SAFETY
• Always check that the power supply corresponds to the voltage on the rating plate.
• Power tool plugs must match the outlet. Never modify the plug in any way. Do not use adapter plugs with earthed
power tools. Unmodified plugs and matching outlets will reduce the risk of an electric shock.
• Avoid body contact with earthed surfaces such as pipes, radiators, kitchen ranges and refrigerators. There is an
increased risk of an electric shock if your body is earthed.
• Do not expose power tools to rain or wet conditions. If water gets inside a power tool, it will increase the risk of an
electric shock.
• Do not damage the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep the cord away
from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of an electric shock.
• When operating a power tool outdoors, use an extension cable suitable for outdoor use. Using a cord suitable for
outdoor use reduces the risk of an electric shock.
• If operating a power tool in a damp location is unavoidable, use a power supply protected by a residual current
device (RCD). Using an RCD reduces the risk of an electric shock.
2.3 PERSONAL SAFETY
3
NORDIC
• Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool
when you are tired or under the influence of drugs, alcohol or medication. A moment of inattention when operating
a power tool may result in serious personal injury.
• Use safety equipment. Always wear eye protection. Using safety equipment such as a dust mask, non-skid safety
shoes, a hard hat, or hearing protection whenever it is needed will reduce the risk of personal injury.
• Avoid accidental starts. Ensure the switch is in the off position before inserting the plug. Carrying power tools with
your finger on the switch or plugging in power tools when the switch is in the on position makes accidents more
likely.
• Remove any adjusting keys or spanners before turning on the power tool. A spanner or key left attached to a
rotating part of the power tool may result in personal injury.
• Do not reach out too far. Keep your feet firmly on the ground at all times. This will enable you retain control over the
power tool in unexpected situations.
• Dress properly. Do not wear loose clothing or jewelery. Keep your hair, clothing and gloves away from the power
tool. Loose clothes, jewelery or long hair can become entangled in the moving parts..
• If there are devices for connecting dust extraction and collection facilities, please ensure that they are attached and
used correctly. Using such devices can reduce dust-related hazards.
2.4 POWER TOOL USE AND CARE
• Do not expect the power tool to do more than it can. Use the correct power tool for what you want to do. A power
tool will achieve better results and be safer if used in the context for which it was designed.
• Do not use the power tool if the switch cannot turn it on and off. A power tool with a broken switch is dangerous and
must be repaired.
• Disconnect the plug from the power source before making adjustments, changing accessories, or storing power
tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.
• Store power tools, when not in use, out of the reach of children and do not allow people who are not familiar with
the power tool or these instructions to operate it. Power tools are potentially dangerous in the hands of untrained
users.
• Maintain power tools. Check for misalignment or jammed moving parts, breakages or any other feature that might
affect the operation of the power tool. If it is damaged, the power tool must be repaired. Many accidents are caused
by using poorly maintained power tools.
• Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to jam
and are easier to control.
• Use the power tool, accessories and cutting tools, etc., in accordance with these instructions and in the manner
intended for the particular type of power tool, taking into account the working conditions and the work which needs
to be done. Using a power tool in ways for which it was not intended can lead to potentially hazardous situations.
2.5 SERVICE
Your power tool should be serviced by a qualified specialist using only standard spare parts. This will
4
NORDIC
ensure that it meets the required safety standards.
Special safety instructions for Cordless Branch Cutter
• This appliance is not intended for use by persons (including children) with reduced physical, sensory
or mental capabilities, or lack of experience and knowledge, unless they have been given supervision
or instruction concerning use of the appliance by a personresponsible for their safety.
• Children should be supervised to ensure thatthey donot play with the appliance.
• Minors should never be allowed to operate the tool; it should never be left unattended and when not
in use should be stored in a locked place out of the reach of children.
• Don’t use the machine or perform battery charging operations in the rain.
• Don’t leave the machine in rain or wet locations.
• Keep bystanders well away from your work area.
• Be careful not to catch foreign matter between the blades. If the blades are jammed with foreign
matter, immediately switch off the machine. Then remove the foreign matter from the blades.
• Take care, avoid cutting electrical wires that may be hidden.
• Keep your free hand away from the cutting area. Never touch the blades. They are very sharp and you
may cut yourself.
• Be vigilant when operating to ensure that the fingers on the hand used to hold or move twigs to be
pruned are not exposed to the cutting blade.
• Don’t force the machine to make it cut. You could slip and injure yourself or cut something else
unintentionally.
• Always check the blades carefully before operation.
• Handle the blades with extreme care to prevent cuts or injury from the blades.
• Remove the battery after each use and before attempting to perform inspection or maintenance.
• Always wear protective gloves when using, adjusting or cleaning the machine.
• Only use the machine for it’s intended use (see “Intended Use”).
ADDITIONAL SAFETY INSTRUCTIONS
FOR BATTERIES AND CHARGERS
Use only batteries and chargers applicable for this machine.
4.1 BATTERIES
5
NORDIC
• Never attempt to open for any reason.
• Do not store in locations where the temperature may exceed 40 °C.
• Charge only at ambient temperatures between 4 °C and 40 °C.
• When disposing of batteries, follow the instructions given in the section “Protecting the environment”.
• Do not cause short circuits. If connection is made between the positive (+) and negative (-) terminal directly or via
• Do not heat. If batteries are heated to above 100 °C, sealing and insulating separators and other polymer
components may be damaged resulting in electrolyte leakage and/or internal short circuiting leading to heat
generation causing rupture or file. Moreover do not dispose of the batteries in fire, explosion and/or intense burning
may result.
• Under extreme conditions, battery leakage may occur. When you notice liquid on the battery, proceed as follows:
• Carefully wipe the liquid off using a cloth. Avoid skin contact.
• In case of skin or eye contact, follow the instructions below:
1. Immediately rinse with water. Neutralize with a mild acid such as lemon juice or vinegar.
2. In case of eye contact, rinse abundantly with clean water for at least 10 minutes.
3. Consult a physician.
Fire hazard! Avoid short-circuiting the contacts of a detached battery. Do not incinerate the battery.
4.2 CHARGERS
• Never attempt to charge non-rechargeable batteries.
• Have defective cords replaced immediately.
• Do not expose to water.
• Do not open the charger.
• Do not probe the charger.
• The charger is intended for indoor use only.
SYMBOLS
In this manual and/or on the machine the following symbols are used:
Denotes risk of personal injury or damage to the tool.
6
NORDIC
Read manual before use
Wear eye protection
Wear ear protection
Wear safety gloves
Wear respiratory protection
In accordance with essential requirements of the European directive(s)
Class II - The machine is double insulated; Earthing wire is therefore not necessary (only for
charger)
Ambient temperature 40°C max. (Only for battery)
Do not expose charger and battery pack to water
Use battery and charger only in closed rooms
Do not incinerate battery pack or charger
7
NORDIC
6. INTENDED USE
• This machine is intended for domestic use in pruning branches and plants with a thickness up to 15 mm
(hardwood) and 20 mm (softwood).
• NOTICE: DO NOT CUT OTHER MATERIAL SUCH AS WIRE, STEEL WIRE, STONE, PLASTIC, AND SO ON.
7. BEFORE YOU START
7.1 Installing the battery (Fig. 2a/2b)
Press the both side of the batterypack as shown in Fig. 2a and push the batterypack into the mount
provided. When the batterypack is positioned as in Fig. 2b, make sure that the batterypack latch in place!
To remove thebattery pack, proceed in reverse order.
7.2 Charging the battery (Fig.3)
1. Take the battery pack out of the equipment.Do this by pressing the both side of the batterypack.
2. Check that your mains voltage is the same asthat marked on the charger rating plate. Connect thepower
plug of the charging unit to a socketoutlet, then insert the charging unit to battery pack.The red LED was
always light.
3. The charging unit will end the charging automatically when the battery is fully charged(after approx. 3~5
hours). The green LED thenlights up and the red LED light out.
The battery pack can become a little warm duringthe charging. This is normal. If the battery packfails to
charge, the green and red LED in the battery light up. check:
• whether there is voltage at the socket outlet
• whether there is good contact at the charging contacts
If the battery pack still fails to charge, send
• the Battery charger
• and the battery packto our customer service center.
To ensure that the battery pack provides long service,you should take care to recharge it promptly.You
must recharge the battery pack when younotice that the power of the cordless pruner drops. Never fully
discharge the battery pack.This will cause it to develop a defect.
8
NORDIC
8. OPERATION
WARNING: Before any work on the machine (e. g. maintenance, changing the tool, etc.) as well as during its
transport and storage, Safety lock-off in the offposition. There is danger of injury when the On/Off switch
is unintentionally actuated.
To close the blade 1(Fig. 1) activate the safety lock-off (Fig. 1 / Item 4) by pushing it forward and pressing
the ON/OFF switch (Fig. 1 /Item 3) at the same time. To open the blade 1, let go of the ON/OFF switch(Fig.
1 / Item 3).
Never operate the machine in an awkward posture.This may cause serious injury.
Keep your free hand away from the cutting area. Never touch the blades. They are very sharp and you may
cut yourself. Always wear protective gloves while pruning.
8.1 Changing the blade(Fig.4a-4c)
Warning! Remove battery from pruner before Changing the blade.
Always wear protective gloves when Changing the blade.
Never attempt to operate the machine withoutthe blade, spacer or screw correctly secured
to prevent damage to the machine.
To remove the blade 1, Use a Hexagon wrench socket key (not provided) to remove the blade nut 12 which
secures the blade. Remove the blade wave washer 10 and the washer 9 then remove the blade screw
11(Fig.4a). Removethe blade 1 along 45 ° direction (Fig.4b).
To Insert the blade 1, Be careful not to allow any foreign matter to become attached to the blade gear and
do not damage it. FirstInsert part of the tooth of the blade 1 into the case as shown(Fig.4c), then rotate the
blade 1until the hole of the blade 1 is aligned to the hole of the aluminum gearbox.Incorrect location of the
blade will damage the machine. Refit the blade screw then refit the washer 9 and the wave washer 10, at
last tighten the blade nut 12.Do not over tighten.
9. CLEANING AND MAINTENANCE
Cleaning, maintenance andordering of spare parts
Warning!Always wear protective gloves when using, adjustingor cleaning the machine.
9.1 Cleaning
• Keep all safety devices, air vents and themotor housing free of dirt and dust as far aspossible. Wipe the
equipment with a cleancloth or blow it with compressed air at lowpressure.
9
NORDIC
• We recommend that you clean the device immediately each time you have finishedusing it.
• Clean the equipment regularly with a moistcloth and some soft soap. Do not usecleaning agents or
solvents; these couldattack the plastic parts of the equipment. Ensurethat no water can seep into the
device.
• A few drops of oil (e.g. sewing machine oil)will improve the cutting performance of the blades, but never
apply any grease to the blades.
Important!
Never clean the tool under running water- and particularly never with high pressure -because of the
potential danger to personsand property. Keep your cordless pruner in a dry and frostproofplace. Choose
a place that children areunable to enter.
9.2 Maintenance
• To achieve good results you should keep theblades sharp at all times. The tool should be thoroughly
cleaned bothbefore and after use.
• There are no parts inside the equipmentwhich require additional maintenance.
9.3 Ordering replacement parts:
Please quote the following data when ordering
replacement parts:
• Type of machine
• Article number of the machine
• Identification number of the machine
11. ENVIRONMENT
Should your appliance need replacement after extended use, do not dispose of it
With the household refuse, but in an environmentally safe way.
Waste produced by electrical machine items should not be handled like normal
Household rubbish. Please recycle where recycle facilities exist. Check you’re your Local Authority or
retailer for recycling advice.
10
NORDIC
2.1 LAYOUT FIG 1A/1B/4A
1: Blade - moving
2: Blade - fixed
3: ON/OFF switch
4: Safety lock-off
5: Blade guard
6: Battery
7: Battery charger
8: Cord
9: The blade washer
10: The blade wave washer
11: The blade screw
12: The blade nut
11
NORDIC
5.1 INSTALLING THE BATTERY (FIG 2A/2B)
Press the both side of the battery pack as shown
in Fig 2a and push the battery pack into the mount
provided. When the battery pack is positioned as
in Fig 2b, make sure that the battery pack latch is
in place! To remove the battery pack, proceed in
reverse order.
5.2 CHARGING THE BATTERY (FIG 3)
1: Take the battery pack out of the equiptment. Do
this by pressing the both side of the battery pack.
2: Check that your mains voltage is the same as
that marked on the charger rating plate. Connect
the power plug of the charging unit to a socket
outlet then insert the charging unit to battery pack.
The red LED was always light.
3: The charging unit will end the charging
automatically when the battery is fully charged
(after approx 3~5 hours) The green LED then lights
up and the red LED light out.
The battery pack can become a little warm during
the charging. This is normal. If the battery pack
fails to charge, the green and red LED in the battery
pack light up.
Check: whether there is voltage at the socket
outlet, whether there is a good contact at the
charging contacts
If the battery pack still fails to charge, send the
battery charger and the battery pack to our
customer service center.
To ensure the battery pack provides long service
to you. You must recharge the battery when you
notice that the power of the cordless pruner drops.
12
NORDIC
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
Nordic POBA4750 is a powerful and versatile tool designed to make pruning and cutting tasks easier and more efficient. With its sturdy construction and sharp blades, it can effortlessly cut through branches up to 15 mm (hardwood) and 20 mm (softwood), making it ideal for maintaining your garden or orchard.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
SereneLife PSPR190 Owner's manual
-
SereneLife PSPR170 Owner's manual
-
Northern Industrial Tools ET2701 Owner's manual
-
Black & Decker BCASK861D User manual
-
Alpina Garden MT2148Li Operating instructions
-
Black & Decker BCASK8967D2 User manual
-
Craftsman 315115160 Owner's manual
-
BLACK DECKER BCPP18 Cordless Power Pruner User manual
-
Scotts LSS10272PS User manual
-
Ryobi P2500 User manual
