Scotts LSS10272PS User manual

Brand: Scotts

Model: LSS10272PS

Type: User manual

This manual is also suitable for

Model PR17216PS

OWNER’S MANUAL

Cordless 7.2 Volt Lithium Pruner with Pole

Thank you for your purchase.

DO NOT RETURN THIS PRODUCT TO THE STORE. OPERATING, ASSEMBLY,

PARTS, SERVICE QUESTIONS? GO TO SCOTTS.AMERICANLAWNMOWER.COM

OR CALL 1-800-618-7474 BETWEEN 8:00 AM—5:00 PM EST FOR ASSISTANCE.

SAVE THIS MANUAL FOR FUTURE REFERENCE

This product has been engineered and manufactured to our high standard for dependability, ease of operation, and

operator safety. Properly cared for, it will give you years of rugged, trouble-free performance.

WARNING: To reduce the risk of injury, the user must read and understand the owner’s manual

before using this product.

CA Compliant Charger Included (Model No. HYCH0900400U)

BATTERY MUST BE

CHARGED BEFORE FIRST

USE. TWO TO THREE INITIAL

CHARGING/DISCHARGING

CYCLES MAY BE REQUIRED

TO ACHIEVE MAXIMUM RUN

TIME/CAPACITY.

TO REDUCE RISK OF INJURY: Before any use

be sure everyone using this product reads and

understands all safety instructions and other

information contained in this manual.

WARNING: Personal Injury and Damage! Keep

your hands and feet away from the cutting tool,

especially when the products are switched on!

Never adjust the cutting head when the product is

in the “on” position. Do not touch moving blades.

Save these instructions and review frequently prior

to use and in instructing others.

WARNING: When using electric appliances, basic

safety precautions should always be followed to

reduce risk of fire, electric shock, and personal

injury, including the following:

READ ALL INSTRUCTIONS

AVOID DANGEROUS ENVIRONMENTS - Do

not use this product in the rain or in damp or wet

conditions. Do not operate in gaseous or explosive

atmospheres. Motors in these products normally

spark, and the sparks might ignite fumes.

DRESS PROPERLY- Don’t wear loose clothing or

jewelry and wear protective hair covering to contain

long hair. They can be caught in moving parts.

Use of rubber gloves and protective footwear is

recommended when working outdoors.

USE SAFETY GLASSES - Wear safety glasses

with side shields or goggles that are marked to

comply with ANSI Z87.1 standard when operating

this product. Use face or dust mask if environment is

dusty.

DANGER: Risk of cut. Keep hands away from

blades.

USE RIGHT APPLIANCE - Do not use this product

for any job except that for which it is intended.

WARNING: Switch off before adjusting or cleaning.

CAUTION: The blades continue to move for a few

seconds after the tool is switched off.

AVOID UNINTENTIONAL STARTING - Do not carry

this product with finger on switch.

IMPORTANT! Any use which is not expressly

permitted in the manual may result in damage to

the tool and place the use in serious danger.

Please carefully read the restrictions in the

operating instructions.

IMPORTANT! Before each use check for damaged

or worn parts. Check for alignment of moving parts,

binding of moving parts, breakage, mounting and

any other condition that may affect its operation.

Any part that is damaged should be properly

repaired or replaced. For assistance call our

customer service help line at 1-800-618-7474.

STORE INDOORS-When not in use, this product

should be stored indoors in a dry location out of

reach of children.

STAY ALERT - Watch what you are doing. Use

common sense. Do not operate this product when

you are tired or under the influence of drugs, alcohol

or medications.

DANGER: If blade jams on any electrical cord or

line, DO NOT TOUCH THE BLADE! IT CAN

BECOME ELECTRICALLY LIVE AND VERY

DANGEROUS. Release the unit in the safest

manner possible. Disconnect the damaged

electrical cord or line from the power source. If

possible, do so safely, if in doubt, call an electrician

or the electrical contractor for assistance. Failure to

heed this Danger can result in serious personal

injury and possible death.

LIGHTING - Only operate this tool in daylight or

good artificial light.

DON’T OVERREACH - Keep proper footing and

balance at all times.

DANGER: Make sure trigger switch is off and

safety button is not pushed when clearing jammed

material from blades.

MAINTAIN TOOL WITH CARE-Keep blades sharp

and clean for best performance and to reduce the

risk of injury. Keep handle dry, clean and free from

oil and grease.

KEEP CHILDREN AWAY - All visitors, children and

pets should stay at a safe distance from the work

area.

WARNING: California Proposition 65:

This product contains chemicals known to the State

of California to cause cancer, birth defects or other

reproductive harm.

WARNING: Cancer and Reproductive Harm -

www.P65Warnings.ca.gov.

CAUTION: Always hold the pole pruner with your

right hand on the rear handle and your left hand on

the front aluminum pole. Holding the pole pruner

with your hands in the wrong positions increases

the risk of injury and must therefore be avoided.

CAUTION: Always wear suitable working clothes to

prevent injuries to the head, hands and feet. For

this purpose wear a helmet, safety goggles (or

visor), high boots (or strong shoes and long

trousers made of tough fabric) and work gloves.

CAUTION: Plan an escape route from falling

branches in advance. Make sure that this escape

route is free of obstacles which could restrict or

prevent free movement. Keep in mind that freshly

cut grass or bark is slippery.

CAUTION: Hold the tool by insulated gripping

surfaces only, because the pole pruner may

contact hidden wiring or its own cord.

CAUTION: Never stand below the branch to be

cut. Potential risk of injury from falling branches

projectiles!

CAUTION: The machine is not protected against

electric shock when coming into contact with

high-voltage lines.

IMPORTANT SAFETY WARNINGS

GENERAL SAFETY

Model PR17216PS

Precautions that involve your safety.

CAUTION! Read the instruction manual and follow the warning and safety instructions!

CAUTION! Always wear eye protection.

Do not use in rain or electrical storms.

WARNING! Wear protective gloves!

WARNING! Keep bystanders away. Danger of injury from flying debris!

Always maintain a sufficiently safe distance. Beware of thrown objects. The distance between the machine

and bystanders should be at least 15 meters.

WARNING! Wear safety footwear!

CAUTION! Wear ear protection

Keep sufficient distance away from electrical power lines.

Waste electrical products should not be disposed of with household waste. Please recycle

where facilities exist. Check with your Local Authority or retailer for recycling advice.

EXPLANATION OF SYMBOLS

Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper

interpretation of these symbols will allow you to operate the product better and safer.

CHARGING THE BATTERY

 The battery must be fully charged before using

for the first time. The charging time is 3 to 5

hours. (See page 5 for instructions.)

 Use appliances only with specifically designated

battery packs. Use of any other battery

packs may create a risk of injury and fire.

 To protect the lithium battery against deep

discharging, when the battery is flat, the tool

will automatically switch off via a protective

circuit.

If the On/Off switch is used continually at this point,

the lithium battery can be damaged. Do not try to

continue to use the tool before recharging the

battery.

GENERAL SAFETY

FCC Warnings:

Please note that changes or modifications to this

product not expressly approved by the party

responsible for compliance could void the user's

authority to operate the equipment.

NOTE: This equipment has been tested and found to

comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against

harmful interference in a residential installation. This

equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful

interference to radio communications.

However, there is no guarantee that interference will

not occur in a particular installation. If this equipment

does cause harmful interference to radio or television

reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to

correct the interference by one or more of the

following measures:

-- Reorient or relocate the receiving antenna.

-- Increase the separation between the equipment and

receiver.

-- Connect the equipment into an outlet on a circuit

different from that to which the receiver is connected.

-- Consult the dealer or an experienced radio/TV

technician for help.

Model PR17216PS

PRODUCT SPECIFICATIONS

Model: PR17216PS

Input: 7.2V DC, 2.0 Ah

Battery capacity: 2000mAH

Standard Cut Capacity: 0.7 in (18 mm )

Charger (adaptor) input: 100-120V, 50/60Hz AC

Battery charging time: 3 - 5 hours

Weight: 4.2 lb (1.9 kg)

PARTS LIST

1 Blade – moving

2 Blade – fixed

3 On/Off trigger switch

4 Safety lock button

5 Blade guard

6 Battery

7 Charger

Pruner bracket

Power connector

Telescopic pole

Handle safety lock button

Handle On/Off trigger

switch

Clamp coupling

Rotating angle button

8 Pruner cover

Model PR17216PS

GENERAL INSTRUCTIONS

PACKING LIST

- Pruner

- Telescopic Pole

- Pruner Bracket

- Blade Guard

- Battery Charger

- Battery

- Owner’s Manual

UNPACKING

Carefully remove the product from the box. Make sure

that all items listed in the packing list are included.

Inspect all items carefully to make sure no breakage

or damage occurred during shipping.

Do not discard the packing material until you have

carefully inspected and satisfactorily operated the tool.

WARNING: If any parts are damaged or missing

please do not operate this product until the parts are

replaced. Failure to heed this warning could result in

serious personal injury. Call our customer service help

line at 1-800-618-7474 for assistance.

BEFORE STARTING THE EQUIPMENT

INSTALLING THE BATTERY

Press the both side of the battery pack as shown in

Fig.1 and push the battery pack into the mount

provided. When the battery pack is positioned as in

Fig. 2, make sure that the battery pack is locked in

place! To remove the battery pack, proceed in reverse

order.

CHARGING PROCEDURE (Fig.3)

1. Take the battery pack out of the equipment. Do

this by pressing the both

side of the battery pack.

2. Make sure the wall outlet

in your home is normal

household voltage

(AC120V, 60 Hz). Insert

the battery charger plug

into the wall outlet.

3. Insert the charger cable

into the charging inlet on

the battery.

STARTING AND STOPPING

Starting:

1. Push the safety lock button and press the

on/off trigger switch at the same time.

2. Release the safety lock button.

Stopping:

1. Release the on/off trigger switch.

OPERATING INSTRUCTIONS

WARNING: Before any work on the machine (e.

g. maintenance, changing the tool, etc.) as well

as during its transport and storage, ensure

safety lock-off is in the off position. There is

danger of injury when the On/Off switch is

unintentionally actuated.

To close the moving blade, activate the safety

lock-off by pushing it forward and pressing the ON/

OFF switch at the same time. To open the blade,

let go of the ON/OFF switch.

Never operate the machine in an awkward

posture. This may cause serious injury.

Keep your free hand away from the cutting

area. Never touch the blades. They are very

sharp and you may cut yourself. Always wear

protective gloves while pruning.

CHANGING BLADE (Fig.4-6)

Warning: Remove battery from pruner before

Changing the blade.

Always wear protective gloves when Changing

the blade.

Never attempt to operate the machine without

the blade, spacer or screw correctly secured to

prevent damage to the machine.

To remove the moving blade (1), use a Hexagon

wrench socket key (not provided) to remove the

blade nut (2) which secures the blade. Remove the

blade wave washer(3) and the washer (4) then

remove the blade bolt (5). Remove the moving

blade (1) along 45 ° direction.

Model PR17216PS

Fig.1

Fig.2

 During the charging process, it is normal for the

battery pack to warm up.

 Only charge the battery between 0°-37.8°C (32°

-100°F).

 After prolonged use, allow the battery to cool

down before recharging.

 To ensure that the battery pack provides long

service, you should take care to recharge it

promptly. You must recharge the battery pack

when you notice that the power of the cordless

pruner drops. Never fully discharge the battery

pack. This will cause battery damage.

4. The red LED charging indicator lights up to tell

you that the battery pack is on charge. The

battery is fully charged when the red LED is no

longer lit, and green LED lights up.

Fig.3

GENERAL INSTRUCTIONS

To Insert the moving blade (1), be careful not to

allow any foreign matter to become attached to

the blade gear and do not damage it. First Insert

part of the tooth of the blade into the case as shown,

then rotate the blade (1) until the hole of the blade

(1) is aligned to the hole of the aluminum gearbox.

Incorrect location of the blade will damage the

machine. Install the blade bolt then install the

washer (4) and the wave washer (3). Attach the

blade nut (2) and tighten. Do not over tighten.

Model PR17216PS

3 4

USING THE EXTENTION AND ROTATION FEATURE ON

THE CONNECTING POLE

Extend or shorten the

length of the telescopic pole

by loosening the clamp

coupling for telescopic pole

and pull in or push out the

lower section to achieve the

correct length. Then tighten

the coupling.

Adjusting the angle of pruner in the vertical direction

Press the rotating button on both sides for the angle of tilt

adjustment . Set the pruner to the desired tilt. Release the

button and allow the pruner to lock into position to lock the

angle of tilt. Four different locking angles are possible. The

adjusting range is from 0 ° to 90 °.

Adjusting the angle of pruner in the horizontal direction

Holding the connecting pole with one hand, and the pruner

bracket with the other. Rotate the pruner bracket firmly to the

desired angle. The adjusting range is from -90 ° to +90 °.

CONNECTING THE POLE

Using the telescopic long handle. You can prune the

branches farther away .

Holding the connecting pole with one hand, and the front

of the pruner with the other, push the battery pack of the

pruner in to the pruner bracket until the pruner is fully in

place. Close the pruner cover and tighten the butterfly

bolt. Then connect the power connector to the battery

pack on the pruner.

To take apart, proceed in the reverse order.

Butteryfly bolt

Fig.4

Fig.5

Fig.6

Model PR17216PS

MAINTENANCE / CLEANING / STORAGE

MAINTENANCE:

CAUTION: Blades can cause injury. Do not press

the safety lock of the pruner during maintenance

work.

Note: To ensure long and reliable service, regularly

carry out the following maintenance:

 Check for obvious defects such as a damaged

or loose blade, housing, or components.

 If the tool should stop working properly, repair

should be carried out by a qualified individual,

using identical replacement parts.

CAUTION: Never clean the pruner in water

(especially running water), as there is a risk of

personal injury and damage to the pruner.

To obtain good cutting results, always make sure

the blades are sharp, and clean them from time to

time with a soft dry cloth.

A few drops of oil (e.g. sewing machine oil) will

improve the cutting performance of the blades, but

never apply any grease to the blades.

There are no parts inside the equipment which

require additional maintenance.

CLEANING / STORAGE

 Clean the exterior of the tool thoroughly

using a soft brush and cloth. Do not use water,

solvents, or polishes.

 After use, cover the blades with the guard

provided.

 Charge the battery 3 to 5 hours before storing.

 If the tool is to be stored for an extended period

of time or during winter storage, charge the

battery at least once every three months to

protect it from damage.

 Store the tool in a dry secure place out of reach

of children.

 Do not place any other objects on top of the

tool.

 This tool must not be stored in temperatures

over 40°C (104°F) or under direct exposure to

sunlight.

 Do not store the tool in places with static

electricity.

PARTS AND SERVICE

For parts or service, please call 1-800-618-7474 or visit us online at scotts.americanlawnmower.com.

Be sure to provide all relevant information when you call or visit.

REPAIR PARTS (KITS/ ITEMS)

The model/ serial number of this tool is found on a plate or label attached to the housing. Please

record the serial number in the space provided below.

MODEL NUMBER PR17216PS__

SERIAL NUMBER_______________

CALL US FIRST !!

Call us first with questions about operating or maintaining your product

at 1.800.618.7474 between 8:00 a.m. – 5:00 p.m. Eastern

Standard Time, or get assistance on scotts.americanlawnmower.com.

BATTERY DISPOSAL

Remove the battery pack from the product. Cover the terminals with heavy duty adhesive tape. Do not attempt to destroy or disassemble battery pack

or remove any components. This product contains lithium-ion batteries which must be recycled or disposed of properly. Local, state or federal laws

may prohibit disposal of these batteries in ordinary trash.

The RBRC seal on the li-ion battery pack indicates that the costs to recycle the battery pack at the end of its useful life has already been paid

by The Great States Corporation American Lawn Mower Company. It is illegal to place spent li-ion batteries in the local municipal solid waste

or in the trash. RBRC in cooperation with The Great States Corporation American Lawn Mower Company has provided an environmentally

friendly and easy way to recycle spent li-ion batteries. Just contact your local recycling center or call 1-800-8BATTERY for information on

where to drop off the spent battery.

Always mention the model number when ordering kits/items for this tool.

No. Kit/Item Number Description No.

1 PR-PAK Pole assembly kit 2

Kit/Item Number

LSS-PR-CHK

Description

Charger

In a continued commitment to improve quality, the Manufacturer reserves the right to

make component changes or design changes when necessary.

OWNER’S MANUAL

PR17216PS Cordless 7.2V Lithium Pruner with Pole

Rev. 11/26/2018

WARRANTY POLICY

Scotts Warranty policy

 2 Year limited warranty on all Scotts electric hand tools from date of purchase when used for personal, household, or family use.

The Great States Corp. (GSC)warrants to the original owner that this Scotts product and service part is free from defects in materials and

workmanship and agrees to repair or replace any defective product or part for the warranty period as stated above.

 Warranty voided if used for commercial or industrial purposes or any other improper use as determined by GSC.

 Warranty does not include repairs necessary due to operator’s abuse or negligence (including overloading the product beyond

capacity or immersion in water), or the failure to assemble, operate, maintain or store the product according to the instructions in the

owner’s manual.

 This warranty does not cover

 Wear items, including but not limited to - drive belts & gears, tines, cutting blades, mower blades, saw chains, mulching

blades, blower fans, spool covers, trimmer line, blower and vacuum tubes, guide bars, high pressure hoses, wheels,

handles, augers, worn bags, power cables, and other items subject to wear over time.

 Wear on batteries, including but not limited to – drops, wear and breakage on charger, exposure to extreme temperature

swings (hot or cold), battery left on charger too long, battery left uncharged for too long, and misuse or abuse of the battery.

 This warranty does not cover damage caused by cold, heat, rain, excessive humidity or other environmental extremes.

 This warranty does not cover normal deterioration of the exterior finish or normal wear and tear on the products including, but not

limited to scratches, cracks, dents, or damage caused by outside chemicals.

 This warranty is not transferable and only applies to new products sold directly from an authorized retailer. This warranty does not

apply to any product, new or used, purchased through unauthorized third-party channels. For information on authorized dealers,

contact our customer support hotline at 1-800-618-7474 (Mon-Fri 8am-5pm Est)

 Any incidental, indirect or consequential loss, damage, or expense that may result from any defect or malfunction of the products is

not covered by the warranty.

 The warranty does not include installation, assembly or normal adjustments explained in the operator’s manual. The expense of

delivering the product to the vendor and the expense of returning the product or replacement parts to the owner is not covered by

the warranty.

Additional Warranty Limitations

Some states do not allow the exclusion or limitation on how long an implied warranty lasts, so the above limitation may not apply to you.

Products sold damaged or incomplete, sold ―as is, or sold as reconditioned are not covered under the warranty.

Damage or liability caused by shipping, improper handling, improper assembly, incorrect voltage, improper wiring, improper maintenance,

improper modification or the use of accessories and/or attachments not specifically recommended is not covered by this warranty.

Proof of purchase, original dated sales receipt, must accompany all warranty claims.

For claims go to scotts.americanlawnmower.com or call our customer support hotline from 8am-5pm EST, Mon-Fri at

1-800-618-7474

American Lawn Mower Company

The Great States Corporation

7444 Shadeland Station Way

Indianapolis, IN 46256 USA

Phone 1-800-618-7474

scotts.americanlawnmower.com

Page is loading ...

Modèle n° PR17216PS

MANUEL DE L’UTILISATEUR

Merci pour votre achat.

NE RENVOYEZ PAS CE PRODUIT AU MAGASIN. AVEZ-VOUS DES QUESTIONS

CONCERNANT LE FONCTIONNEMENT, L’ASSEMBLAGE, LES PIÈCES OU LA RÉPARATION

DU PRODUIT? ALLER À SCOTTS.AMERICANLAWNMOWER.COM OU COMPOSEZ LE 1-800-

618-7474 DE 8 h 00 à 17 h 00, HEURE DE L’EST, POUR TOUTE ASSISTANCE.

CONSERVEZ CE MANUEL POUR POUVOIR LE CONSULTER ULTÉRIEUREMENT

Ce produit a été conçu et fabriqué selon nos normes élevées de fiabilité, de facilité d’utilisation et de sécurité de

l’utilisateur. Correctement entretenu, il vous procurera des années de service intensif et sans souci.

AVERTISSEMENT : afin d’éviter de se blesser, l’utilisateur doit lire et comprendre le manuel de

l’utilisateur avant d’utiliser ce produit.

Chargeur conforme à CA est inclus (Modèle n °HYCH0900400U)

LA BATTERIE DOIT ÊTRE

CHARGÉE AVANT LA

PREMIÈRE UTILISATION. DES

CYCLES INITIAUX DE CHARGE /

DÉCHARGE DE DEUX À TROIS

PEUVENT ÊTRE NÉCESSAIRES

POUR OBTENIR UN TEMPS /

CAPACITÉ MAXIMUM.

Page is loading ...

Scotts LSS10272PS User manual

Brand: Scotts

Model: LSS10272PS

Type: User manual

This manual is also suitable for

Download PDF

report

in other languages

français: Scotts LSS10272PS Manuel utilisateur
español: Scotts LSS10272PS Manual de usuario

Scotts LSS10272PS User manual

This manual is also suitable for

Scotts LSS10272PS User manual

in other languages

Related papers

Other documents