Baby Jogger Graco Infant Safe Seat Step 1 Operating instructions

Category
Strollers
Type
Operating instructions
T-Shaped Bar
U-Shaped Bar
Straight Support Bar
Spring Support Bar
Car Seat Adaptor
Instructions
The Single Car Seat Adaptor is designed to be used with
the mounting brackets on the frame of your City Micro,
City Mini, City Classic, City Elite, F.I.T., Summit 360, or
Summit XC single stroller. This car seat adaptor is only
compatible with these stroller models.
This Kit Includes:
2 Adaptor Brackets
1 T-Shaped Support Bar
1 U-Shaped Support Bar
1 Straight Support Bar
1 Spring Support Bar
NOTE: Before you start, please refer to the
Table of Contents on page 2 to ensure you
follow the proper instructions for your car seat.
8575 Magellan Parkway, Suite 1000 • Richmond, VA 23227 • T: 800-241-1848 • F: 804-262-6277 • www.babyjogger.com
The sample product shown on this manual may differ slightly from your production quality Car Seat Adaptor.
This will not affect the assembly or functionality of your Baby Jogger product.
Adaptor Brackets
2
Baby Trend, Britax Chaperone, Cosco, Evenflo, Graco
3
4
5
6
7
Uses the 2 Adaptor Brackets and the
U-shaped Support Bar (facing up)
Baby Trend Expedition
Baby Trend Flex Loc
Baby Trend Gabriella
Baby Trend Stride Sport
Baby Trend StrideZ
Britax Chaperone
Cosco Sprint
Evenflo Aura Elite
Evenflo Embrace 5
Evenflo Embrace LX
Evenflo Journey Premier
Evenflo Nestino Odyssey
Graco Infant SafeSeat Step 1
Graco SnugRide
Graco SnugRide 2
Graco SnugRide 32
Graco SnugRide 35
Peg Perego Primo Viaggio SIP
Peg Perego Primo Viaggio SIP 30/30
Britax Companion
Safety 1st Designer 22
Eddie Bauer Adventurer
Maxi Cosi Cabrio
Maxi Cosi Mico
4 Place your car seat onto the
U-shaped Support Bar. Adjust
the U-shaped Support Bar to
the proper length by sliding the
U-shaped Support Bar in or out,
using the car seat to ensure
proper distance. The car seat
should be supported by the
Adaptor Brackets.
1 Insert Adaptor Brackets into the
corresponding mounting brackets
on your stroller. The Adaptor Brackets
are secure when they click into place.
NOTE: The right and left mounting
brackets on your stroller are
determined by standing in front
of and facing the stroller.
2 Open the compression locks on
the Car Seat Adaptor by flipping
the red latches up.
5 Once the car seat is properly
positioned, close the compression
locks by flipping the red latches
down to hold Support Bars
in place.
3 Insert the U-shaped Support Bar
with the curved end pointing up.
6 Secure your car seat onto the
stroller using the safety belt on
the Car Seat Adaptor Brackets.
NOTE: Always securely fasten the Bracket Adaptor
safety belt over the car seat before operation.
Table of Contents
3
6 Place the T-shaped Bar onto the
car seat and fasten to U-shaped
Support Bar using D-Ring and
Velcro strap.
Britax CompanionPeg Perego
Uses the 2 Adaptor Brackets, the U-shaped
Support Bar (facing up) and the T-shaped Bar
Uses the 2 Adaptor Brackets, the U-shaped
Support Bar (facing down), the Straight
Support Bar and the Spring Support Bar
1 Insert right Adaptor
Bracket into the
corresponding mounting
bracket on your stroller.
The Adaptor Brackets
are secure when they
click into place.
NOTE: The right and
left mounting brackets
on your stroller are
determined by
standing in front of
and facing the stroller.
1 Insert Adaptor Brackets into the
corresponding mounting brackets
on your stroller. The Adaptor
Brackets are secure when they
click into place.
NOTE: The right and left
mounting brackets on your
stroller are determined by
standing in front of and
facing the stroller.
5 Connect the Spring Support
Bar by compressing and
guiding it into the open
holes on the U-Shaped
Support Bar.
2 Insert the Straight
Support Bar into the
holes on the inside of
the Adaptor Brackets
and attach left Adaptor
Bracket to mounting
bracket.
3 Open the compression
locks on the Car Seat
Adaptor by flipping the
red latches up.
2 Open the compression locks on
the Car Seat Adaptor by flipping
the red latches up.
3 Insert the U-shaped Support Bar
with the curved end pointing up.
4 Place your car seat onto the
U-shaped Support Bar. Adjust
the U-shaped Support Bar to
the proper length by sliding
the U-shaped Support Bar in
or out, using the car seat to
ensure proper distance. The
car seat should be supported
by the Adaptor Brackets.
7 Once the car seat
is properly positioned,
close the compression
locks by flipping the red
latches down to hold
Support Bars in place.
8 Secure your car seat onto
the stroller using the
safety belt on the Car
Seat
Adaptor Brackets.
4 Insert the U-shaped
Support Bar with the
curved end pointing down.
5 Once the car seat is properly
positioned, close the compression
locks by flipping the red latches
down to hold Support Bars
in place.
7 Secure your car seat onto the
stroller using the safety belt on
the Car Seat Adaptor Brackets.
4
NOTE: Always securely fasten the Bracket Adaptor
safety belt over the car seat before operation.
NOTE: Always securely fasten the Bracket Adaptor
safety belt over the car seat before operation.
5
6 Place your car seat onto
the U-shaped Support
Bar, making sure that
the Spring and Straight
Support Bars engage the
locking mechanisms
where applicable. Adjust
the U-shaped Support
Bar to the proper length
by sliding the U-shaped
Support Bar in or out,
using the car seat to
ensure proper distance.
The car seat should be
supported by the Adaptor
Brackets.
6
3 Secure your car seat onto the stroller using the safety belt on the
Car Seat Adaptor Brackets.
Maxi CosiSafety 1st & Eddie Bauer
Uses the 2 Adaptor Brackets ONLYUses the 2 Adaptor Brackets, the
U-shaped Support Bar (facing up) and
the Spring Support Bar
1 Insert Adaptor Brackets into the corresponding mounting brackets
on your stroller. The Adaptor Brackets are secure when they click
into place.
NOTE: The right and left mounting brackets on your stroller
are determined by standing in front of and facing the stroller.
2 Place your car seat onto the Adaptor Brackets until it clicks into place.
The car seat should be supported by the Adaptor Brackets.
4 Connect the Spring Support Bar
by compressing and guiding it
into the open holes on the
U-shaped Support Bar.
7 Secure your car seat onto the
stroller using the safety belt on
the Car Seat Adaptor Brackets.
1 Insert Adaptor Brackets into the
corresponding mounting brackets
on your stroller. The Adaptor
Brackets are secure when they
click into place.
NOTE: The right and left
mounting brackets on your
stroller are determined by
standing in front of and
facing the stroller.
5 Place your car seat onto the
U-shaped Support Bar, making
sure that the Spring Support
Bar engages the locking
mechanism where applicable.
Adjust the U-shaped Support Bar
to the proper length by sliding the
U-shaped Support Bar in or out,
using the car seat to ensure
proper distance. The car seat
should be supported by the
Adaptor Brackets.
2 Open the compression locks on
the Car Seat Adaptor by flipping
the red latches up.
3 Insert the U-shaped Support Bar
with the curved end pointing up.
6 Once the car seat is properly
positioned, close the compression
locks by flipping the red latches
down to hold Support Bars
in place.
NOTE: Always securely fasten the Bracket Adaptor
safety belt over the car seat before operation.
NOTE: Always securely fasten the Bracket Adaptor
safety belt over the car seat before operation.
7
Other Available Accessories
Child Tray
Available for single & double strollers. Features cup holder
and easy to clean surface. Child Tray for double requires
use of belly bar.
Belly Bar
Available for single & double strollers. Provides child with
a soft padded area to hold on to when the stroller is in use.
Belly Bar Console
Provides additional storage space for your child’s snacks
and toys.
Rain Canopy
Available for single & double strollers. Made from a BPA &
PVC Free material.
Bug Canopy
Available for single & double strollers. Made from a finely
woven mesh.
Liquid Holster
A self-leveling beverage holder. Fits most round or
square tubing.
Foot Muff
For children 6-18 mo. Keeps legs & feet warm in
inclement weather.
Carry Bag
Available for single & double strollers. Protects your
stroller during transport or storage.
Plush Stroller Hand Muff
Keeps your hands warm and dry while pushing your stroller.
Features a soft and plush interior and weatherproof exterior.
Glider Board
Attaches to rear axle of single or double Baby Jogger stroller
to allow your toddler to ride along. Holds up to 45 lbs.
Bassinet/Pram
A traditional hard based pram with plush padding and
protective sun canopy. Compatible with single strollers only.
Rain Canopy - Bassinet/Pram
Completely encloses the top and sides of the Bassinet/Pram
while providing ventilation in inclement weather. Made from
BPA and PVC Free material.
Cooler Bag
Designed to help keep food or drinks cold. Holds six
12 oz. cans.
MP3 Console
Plug your MP3 player into the console and play music for
you or your child. Features a large storage compartment
and cup holder.
Universal Parent Console
Features a cup holder, insulated cooler pouch and an
additional storage compartment.
Umbrella Holder
Compatible with most full sized umbrellas.
Wheel Bag
Allows you to store your stroller wheels together in
one place.
8575 Magellan Parkway, Suite 1000 • Richmond, VA 23227 • T: 800-241-1848 • F: 804-262-6277 • www.babyjogger.com
For the most up to date information on our list of compatible car seats, please visit the FAQ section
of our website or call Baby Jogger customer service at 800-241-1848.
Car seat models or brands sold internationally are not always confirmed to be compatible with
Baby Jogger’s car seat adaptors. If you need assistance determining the compatibility of your international
car seat, please visit our website to locate the distributor nearest you.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5

Baby Jogger Graco Infant Safe Seat Step 1 Operating instructions

Category
Strollers
Type
Operating instructions

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI