Car Seat
Adapter Kit
Read these
instructions carefully
before use and
keep them for
future reference.
Your child’s safety may be
affected if you do not follow
these instructions.
For Use With:
• City-Single Stroller
• Q-Single Stroller
• Pram Accessory
Kit Includes
This Adapter Kit Includes:
1 – U-Shaped Support Bar
1 – T-Shaped Support Bar
1 – Spring Support Bar
1 – Straight Support Bar
2 – Adapter Brackets (1 – left, 1 – right)
U-Shaped Support Bar
This will be used to install
Peg Perego Primo Viaggio
SIP, Graco, Evenflo, and
Britax Companion car seats.
T-Shaped Support Bar
This will be used to install only
Britax Companion car seats.
Straight Support Bar
This will be used to install only Peg Perego
Primo Viaggio SIP.
Spring Support Bar
This will be used to install only Peg Perego
Primo Viaggio SIP.
Adapter Brackets
These will be used to
install the Pram, Peg
Perego Primo Viaggio SIP,
Graco, Evenflo, Britax
Companion, and Maxi
Cosi car seats.
1
To install the Pram you will need the following adapter part(s):
2 – Adapter Brackets (1 – left, 1 – right)
1. Remove the canopy and seat from stroller frame.
Please refer to the owner manual.
(Be sure to store fabric and hardware for later use.)
2. Secure Right Adapter Bracket to frame directly below the
folding mechanism making sure to align the notches in the
Adapter Bracket over the snap and rivets. (Fig. A)
Repeat to the left side.(Fig. B)
Note: Do not over tighten. Over tightening will damage
the product and void the warranty.
3. Place Pram onto Adapter Brackets, making sure child will be
facing toward stroller handle. Firmly press down on the Pram
until you hear a click which means it’s locked in place. (Fig. C)
Note: The Red compression locks and the support bars are
not applicable when using the Baby Jogger Pram
4. To remove Pram from the Adapter Brackets, press the two
buttons on the Pram handle and lift up carefully.
5. To retract canopy, push button on canopy hinge and push
canopy back out of the way. To use canopy in the extended
position, push button and pull canopy forward.
Note: To avoid safety belt strap catching on wheels, secure them
to each other in order to avoid hanging.
Pram
(Fig. A)
(Fig. B)
(Fig. C)
2
Peg Perego Primo Viaggio SIP
To install the Peg Perego Primo Viaggio SIP you will need the
following part(s):
2 – Adapter Brackets (1 – left, 1 – right)
1 – U-Shaped Support Bar
1 – Spring Support Bar
1 – Straight Support Bar
1. Remove the canopy and seat from stroller frame. Please refer to the
owner manual. (Be sure to store fabric and hardware for later use.)
2. Secure Right Adapter Bracket to frame directly below the
folding mechanism making sure to align the notches in the
Adapter Bracket over the snap and rivets. (Fig. A)
Repeat to the left side. (Fig. B)
Note: Do not over tighten. Over tightening will damage the product
and void the warranty.
3. Before tightening Left Adapter Bracket to frame, align the
Straight Support Bar into Adapter Bracket hole. (Fig. B)
Once in place tighten Left Adapter Bracket. (Fig. B)
4. Open the compression locks by flipping the Red Latches up to allow
U-Shape Support Bar to be inserted into Adapter Brackets. (Fig. C)
5. Insert the U-Shaped Support Bar with the curved end pointing down
into the Adapter Brackets.
6. Insert Spring Support Bar into front of U-Shaped Support Bar
by squeezing in. (Fig. E)
7. Place the car seat onto the U-Shape Support Bar making sure
that the Spring and Straight Support Bars engage the locking
mechanisms on the Peg Perego car seat. Adjust U-Shape Support
Bar to proper length by sliding U-Shape Support Bar in and out.
Use car seat to ensure proper distance. (Fig. C)
Close compression locks by flipping the Red latches down. (Fig. D)
8. Secure the car seat to stroller using Safety Belt. (Fig. F)
3
(Fig. A)
(Fig. B)
(Fig. C)
(Fig. D)
(Fig. E)
(Fig. F)
4
Graco/Evenflo Car Seat
To install a Graco/ Evenflo car seat you will need the following
adapter part(s):
2 – Adapter Brackets (1 – left, 1 – right)
1 – U-Shaped Support Bar
1. Remove the canopy and seat from stroller frame. Please refer to the
owner manual. (Be sure to store fabric and hardware for later use.)
2. Secure Right Adapter Bracket to frame directly below the folding
mechanism making sure to align the notches in the Adapter
Bracket over the snap and rivets. (Fig. A)
Repeat to the left side. (Fig. B)
Note: Do not over tighten. Over tightening will damage the product
and void the warranty.
3. Open the compression locks by flipping the Red Latches up
to allow U-Shape Support Bar to be inserted into Adapter
Brackets. (Fig. C)
4. Insert the U-Shaped Support Bar with the curved end pointing up
into the Adapter Brackets. (Fig. D)
5. Place car seat onto U-Shaped Support Bar. Adjust U-Shape
Support Bar to proper length by sliding frame in and out. Use car
seat to insure proper distance. Close compression locks by flipping
the red latches down. (Fig. E)
6. Secure the car seat to stroller using Safety Belt. (Fig. F)
Note: The Straight and Spring Support Bars are not applicable when
using a Graco or Evenflo car seat.
5
(Fig. A)
(Fig. B)
(Fig. C)
(Fig. D)
(Fig. E)
(Fig. F)
6
Britax Companion Car Seat
To install the Britax Companion car seat you will need the
following adapter part(s):
2 – Adapter Brackets (1 – left, 1 – right)
1 – U-Shaped Support Bar
1 – T-Shaped Support Bar
1. Remove the canopy and seat from stroller frame. Please refer to the
owner manual. (Be sure to store fabric and hardware for later use.)
2. Secure Right Adapter Bracket to frame directly below the
folding mechanism making sure to align the notches in the
Adapter Bracket over the snap and rivets. (Fig. A)
Repeat to the left side. (Fig. B)
Note: Do not over tighten. Over tightening will damage the product
and void the warranty.
3. Open compression locks by flipping the red latches up. (Fig. B)
4. Insert the U-Shaped Support Bar with the curved end pointing up
into Adapter Brackets. (Fig. D)
5. Place car seat onto U-Shaped Support Bar. Adjust U-Shape
Support Bar to proper length by sliding frame in and out.
Use car seat to insure proper distance. Close compression locks
by flipping the red latches down. (Fig. E)
6. Place the T-Bar onto car seat as shown and tighten strap using
D-Ring and Velcro. (Fig. F)
7. Secure the car seat to stroller using Safety Belt.
Note: The Straight Support Bar is not applicable when using the
Britax Companion car seat.
7
(Fig. A)
(Fig. B)
(Fig. C)
(Fig. D)
(Fig. E)
(Fig. F)
To install the Maxi Cosi car seat you will need the following
adapter part(s):
2 – Adapter Brackets (1 – left, 1 – right)
1. Remove the canopy and seat from stroller frame. Please refer to the
owner manual. (Be sure to store fabric and hardware for later use.)
2. Secure Right Adapter Bracket to frame directly below the
folding mechanism making sure to align the notches in the
Adapter Bracket over the snap and rivets. (Fig. A)
Repeat to the left side.(Fig. B)
Note: Do not over tighten. Over tightening will damage the product
and void the warranty.
3. Place car seat onto the Adapter Brackets, making sure the child
will be facing toward stroller handle. Firmly press down on the car
seat to lock into place. (Fig. C)
4. Secure the car seat to stroller using Safety Belt. (Fig. D)
Note: The red compression locks and support bars are not applicable
when using the Maxi Cosi car seat.
Maxi Cosi Car Seat
8
9
(Fig. A)
(Fig. B)
(Fig. C)
(Fig. D)
Our #1 goal is to make sure you are happy with
our product. If you have any comments or
suggestions, we would love to hear from you.
BJC CSA 6.20.06
1.800.241.1848
CustomerService@babyjogger.com
Baby Jogger is a Division of Dynamic Brands
8575 Magellan Parkway, Suite 1000 • Richmond, VA 23227
T: 800.241.1848 • F: 804.262.6277
www.babyjogger.com
Thank You!
/
