Generation Lighting HS586BUBZLEDS830MPT Installation guide

Category
Coaxial cables
Type
Installation guide
Installation Instructions for
LED Pendants
980FSJLEDP
Adjust the Fixture Height
SOCKET ASSEMBLY
FIXTURE COAXIAL
CABLE
1
GP I :ENERAL RODUCT NFORMATION
This product is ETL listed and suitable only for indoor dry locations
and approved for use at any height above the finished floor.
1A
(H)
Fusion Jack
1.2
Fusion Jack LED Pendants
Feed the fixture coaxial cable through the glass shade. Slide the
glass shade down the cord and rest it onto the socket
assembly.
Cut the coaxial cable to the desired length.
1
2
SET SCREW
Back out (do not remove) the set screw on tip of the
connector with the provided Allen wrench.
ALLEN WRENCH
3
Back out (do not remove) the set screw on the conical
connector with the provided Allen wrench.
SET SCREW
ALLEN WRENCH
4
1B
1C
4
3
CONNECTOR
CAUTION - RISK OF FIRE
This product must be installed in accordance with
the applicable installation code by a person familiar
with the construction and operation of the product
and the hazards involved.
Use minimum 90°c supply conductors.
2
1D
Gently twist the end of the coaxial cable between thumb and
forefinger.
5
5
Tap the conical connector on a hard surface with the set screw
facing down, so the plate inside drops into place.
SURFACE
PLATE
1E
6
1F
7
Feed and push the coaxial cable into the conical connector.The
coaxial cable will come to a stop point after being inserted
3/4" into the conical connector.
CONICAL CONNECTOR
OUTER WRAPPED
WIRE STOPS HERE
7
INNER WIRE
STOPS HERE
1G
Keep pushing the coaxial cable into the connector while
rotating the connector to ease feeding the inner wire into the
tip of the connector.The outer wrapped wire will start
wrinkling while being inserted another 1/2" into the connector.
WRINKLE ON OUTER
WRAPPED WIRE
8
8
Look into the sight hole on the top of the connector to make
sure that the inner wire is contacting the end of the connector.
Hold the coaxial cable in place and tighten the set screw on tip
of the connector with the provided Allen wrench. Make sure
this set screw connection is tight.
SIGHT HOLE
ALLEN WRENCH
10
9
INNER WIRE
1H
9
10
1I
Firmly tighten the set screw on the conical connector.
11
11
Pull the coaxial cable toward the fixture to smooth the
wrinkles.
1J
12
12
3
Replacing the Lamp
If necessary, slide the stem up.
Lift the shade up to expose the socket.
Lower the shade onto the socket assembly.
If necessary, slide the stem back down in place.
Unscrew the old lamp.
NOTE: Use only your fingers to replace the lamp.
2C
LAMP
SHADE
SOCKET
Screw the new lamp into the socket.
SHADE
NOTE: To reduce the risk of a burn or electric shock
during relamping, disconnect the power to the fixture.
The lamp is rated at 6 watts at 12 volts.
2A 2C
2B
2D
1
3
4
5
2
3
4
2
6
4
SAVE THESE INSTRUCTIONS!
7400 Linder Ave, Skokie, IL 60077
800.323.3226 - 847.626.6300
www.lbllighting.com
© 2014 LBL Lighting.All rights reserved.The "LBL Lighting" graphic is a
registered trademark of LBL Lighting. LBL Lighting reserves the right to
change specifications for product improvements without notification.
A Generation Brands Company
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Generation Lighting HS586BUBZLEDS830MPT Installation guide

Category
Coaxial cables
Type
Installation guide

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI