Aries S223043-2 Installation guide

Aries
Brand
Aries
Model
S223043-2
Category
Car kits
Type
Installation guide

Aries S223043-2 side bars are a great addition to any vehicle, providing both style and functionality. Made from durable stainless steel, these side bars are built to last and can withstand even the toughest conditions. They are also easy to install, with all the necessary hardware included.

With their 4" oval design, the Aries S223043-2 side bars provide a wide step area, making it easy to get in and out of your vehicle. They also feature a non-slip surface to ensure your footing is secure, even in wet or icy conditions.

In addition to their practical benefits, the Aries S223043-2 side bars also enhance the look of your vehicle. Their sleek design and polished finish will complement any vehicle style.

Aries S223043-2 side bars are a great addition to any vehicle, providing both style and functionality. Made from durable stainless steel, these side bars are built to last and can withstand even the toughest conditions. They are also easy to install, with all the necessary hardware included.

With their 4" oval design, the Aries S223043-2 side bars provide a wide step area, making it easy to get in and out of your vehicle. They also feature a non-slip surface to ensure your footing is secure, even in wet or icy conditions.

In addition to their practical benefits, the Aries S223043-2 side bars also enhance the look of your vehicle. Their sleek design and polished finish will complement any vehicle style.

PA
GE 1 • S223043-2-INS-RB • 877.287.8634 • NEED ASSISTANCE? • ARIESAUTOMOTIVE.COM
Level of Difficulty
Easy
Parts List
1 Driver / left side bar
1 Passenger / right side bar
6 Mounting bracket, universal
18 Flat washer, M8
18 Flat washer, M8 nylon
18 Nylock nut, M8 x 1.25, CL8.8
12 Flat washer, 10mm
12 Lock washer, 10mm
12 Hex bolt, 10mm
INSTALLATION MANUAL
S223043-2
Tools Required
Ratchet Level
Socket, 13mm Socket, 16mm
Scan
for helpful
install tips
Notes and Maintenance
Before you begin installation, read all instructions thoroughly.
Proper tools will improve the quality of installation and reduce the time required.
To protect the product, wax after installing. Regular waxing is recommended to
add a protective layer over the finish. Do not use any type of polish or wax that may
contain abrasives that could damage the finish.
For stainless steel and aluminum, polish may be used to clear small scratches
and scuffs on the finish. Mild soap may be used also to clean the product.
Product Image
Brackets
Front
Rear
ARI
ESAUTOMOTIVE.COM • NEED ASSISTANCE? • 877.287.8634 • S223043-2-INS-RB • PAGE 2
Step 1
Starting on the driver side, locate the
three mounting locations on the inside
of the rocker panel.
There will be three 8mm studs in
each location to secure the brackets.
Step 2
Locate the six mounting brackets. The
mounting brackets are universal and will
fit on both the driver and passenger sides.
Step 3
Starting at the front, place a nylon
washer over the factory bolts, followed
by the bracket.
Note: It is important to install the nylon
washers first to prevent a corrosion
effect from the aluminum body and steel
bracket.
Step 4
Add an 8mm flat washer, and
secure with a nylock nut.
Snug the hardware with a
13mm socket, but do not fully tighten.
PA
GE 3 • S223043-2-INS-RB • 877.287.8634 • NEED ASSISTANCE? • ARIESAUTOMOTIVE.COM
Step 5
Repeat steps 3 and 4 to install the
middle and rear brackets on the driver
side mounting locations.
Snug the hardware,
but do not fully tighten.
Step 6
Carefully place the side bar onto the
brackets and ensure the rivet nuts on
the bottom of the side bar line up with
the brackets.
Attach the side bar to the brackets
using the supplied 10mm hex bolt,
lock washers and flat washers.
Snug the hardware,
but do not fully tighten.
Step 7
With all the hardware installed, we
recommend tightening all of the vehicle
connections first, followed by the side
bar connections.
Check for level and adjust if necessary.
Once aligned, tighten all hardware.
Repeat this entire process
on the passenger side.
Step 8
Remember to do periodic inspections
to make sure that all hardware is secure
and tight.
To protect your investment, we
recommend you apply a layer of
nonabrasive wax.
Congratulations on the installation of
your brand new Aries 4" oval side bars.
  • Page 1 1
  • Page 2 2
  • Page 3 3

Aries S223043-2 Installation guide

Aries
Brand
Aries
Model
S223043-2
Category
Car kits
Type
Installation guide

Aries S223043-2 side bars are a great addition to any vehicle, providing both style and functionality. Made from durable stainless steel, these side bars are built to last and can withstand even the toughest conditions. They are also easy to install, with all the necessary hardware included.

With their 4" oval design, the Aries S223043-2 side bars provide a wide step area, making it easy to get in and out of your vehicle. They also feature a non-slip surface to ensure your footing is secure, even in wet or icy conditions.

In addition to their practical benefits, the Aries S223043-2 side bars also enhance the look of your vehicle. Their sleek design and polished finish will complement any vehicle style.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents