Gianni Industries PBT-930 Installation guide

Gianni Industries
Brand
Gianni Industries
Model
PBT-930
Category
Security device components
Type
Installation guide

This manual is also suitable for

GEM’s NEW line of LED illuminated push plate exit
buttons are designed to provide maximum visibility.
The PBT-930 model features a field selectable green/
red illumination (Blue/red is available for PBT-950).
The full-featured PBT-940WT and PBT-960WT offer
a HOPPING CODE RF wireless transmitter for wired/
wireless retrofit applications and also come with a
wireless controller for up to 15 units.
Features
PBT-950 Series - LED Push Plate Exit Buttons
General Descriptions
1 Determine the wire access location and drill a hole
2
3
4
5
6
Power Input
12/24 VDC/AC
Single pole double throw (SPDT)
Installation Steps
1
2
3
1
2
3
1
2
3
(
Red)(Push)(Green)
(
Green)(Push)(Red)
1
2
3
Copyright © All Rights Reserved. P-MU-PBT-950 Published: 2019.08.30
Installation Instructions
HOPPING CODE RF wireless transmitter remote
function available for PBT-940WT & PBT-960WT
Stainless and impact resistant illuminated surface
mount box
Super-bright, high efficiency LED technology
LED Red/Green & Red/Blue illuminations to show
door locked/unlocked status
Jumper Settings for LED Illuminations
76.2(3”)
76.2(3”)
&
2 mm
Wrench
PCB!Board
M3x18 Screws x2
4x25 Screws x4
Bottom Box
Front Cover
133
(5.24”)
76.2 (3”)
76.2 (3”)
133 (5.24”)
of sufficient size, or use center knock-out plug.
Drill the 4 required mounting holes 1/8” min (3.2mm).
There are 4 indents provided on 3” (76.2mm) centers
for your convenience.
Pull wiring through access hole, and mount the box
to wall using 4 screws (4x25 screws).
Remove circuit board from package and locate into
the box with terminal strip at top. Wire as per Diagram
(1) below.
Connect power and test for proper operation.
Screw in two M3x18 screws provided with the exit
button into the threaded center inserts, then attach
wires to the front cover and install the front cover over
screws. Using the Allen key (provided), locate the
screws and tighten (by hand only). Complete the
installation.
2
3
1
6
5
4
Output
* Factory default setting: Jumper at JP1 & JP2 position.
1
2
3
1
2
3
DescriptionsPosition
Jumper at JP1 & JP2 position
Jumper at JP2 & JP3 position
(Blue)
(
Blue)
+
NO
COM
NC
Cable
Diagram (1)
The LED switches from Red to
Green (or Blue) after you push
the exit button.
The LED switches from Green
(or Blue) to Red after you push
the exit button.
Specifications
PBT-926
PBT-920
133x133x30mm
GE
M
R
PBT-925 PBT-925BLED
PBT-925GLED
0.5A/120VAC or 1A/24VDC
Copyright © All Rights Reserved. P-MU-PBT-950 Published: 2019.08.30
Dimensions
(LxWxD)
MODELS
Products
Faceplate
Material
Voltage
LED Red
Illumination
LED Blue
Illumination
Contacts
Contact Rating
Hopping Code
RF Wireless
RF Wireless
Controller
LED Green
Illumination
133x133x30mm
PBT-940WT
G
E
M
R
PBT-930
NO./COM./NC. (SPDT)
G
E
M
R
PBT-950
0.5A/120VAC or 1A/24VDC
12/24 VAC/DC
G
E
M
R
PBT-960WT
G
E
M
R
Dimensions
MODELS
Products
Faceplate
Voltage
LED Red
LED Blue
Contacts
Contact Rating
Hopping Code
RF wireless
RF Wireless
LED Green
PBT-926BLED
NO./COM./NC. (SPDT)
PBT-926GLED
12/24 VAC/DC
15A/125 or 250VAC
Stainless Steel
Stainless Steel
(LxWxD)
Material
Illumination
Illumination
Illumination
Controller
62
83
Warranty
Transmitter
Copyright © All Rights Reserved. P-MU-PBT-950 Published: 2019.08.30
Operating Voltage: 12~24 VAC/DC
Current Draw: Pull in: 50mA/12 VDC ,Holding: 20mA/12 VDC
Pull in: 70mA/24 VDC, Holding: 40mA/24 VDC
Output: 1 relay (N.O./COM/N.C.)
Contact Rating: 3A @ 12VDC
Buzzer: The controller starts beeping when the battery is lower than 9.2VDC
LED Indicator: Green indicates power status | Red indicates input and
output status
Relock Time Setting: 1, 3, 5, 10 seconds
Quantities of remote transmitter devices: Up to 15 pcs
Dimensions: 83(L)X 62(W) X 30(D) mm
Transmitting Frequency: 433 KHz
Distance: 50~60 meters
Embedded Modules: Hopping Code IC
WIRELESS
CONTROLLER
The product is warranted against defects in material and workmanship while used in normal service for a period of 1-year
from the date of sale to the original client. The GEM policy is one of continual development and improvement; therefore
GEM reserves the right to change specificaions without notice.
PBT-940WT/960WT Specifications
(Receiver)
Operating Voltage: 12/24 VAC/DC
Current Draw: Pull in: 100mA/12 VDC ,Holding: 80mA/12 VDC
Pull in: 145mA/24 VDC, Holding: 115mA/24 VDC
G
E
M
R
  • Page 1 1
  • Page 2 2
  • Page 3 3

Gianni Industries PBT-930 Installation guide

Gianni Industries
Brand
Gianni Industries
Model
PBT-930
Category
Security device components
Type
Installation guide
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents