Signature Hardware 443752 Installation guide

Signature Hardware
Brand
Signature Hardware
Model
443752
Category
Sanitary ware
Type
Installation guide
HOLLYN PUSH-BUTTON SHOWER SYSTEM
GETTING STARTED
BEFORE YOU BEGIN
We recommend consulting a professional if you are
unfamiliar with installing plumbing fixtures. Signature
Hardware accepts no liability for any damage to the
plumbing, floor, walls, tub, or for personal injury during
installation.
Observe all local plumbing and building codes.
Unpack and inspect the item for shipping damage. If any
damage is found, contact our Customer Relations team
at 1-866-855-2284.
Ensure that you have gathered all the required
materials that are needed for the installation.
For the following installation instructions, it is
assumed that the wall has been opened and that the
existing shower set has been removed.
Before you begin, the main water supply to your home
should be shut off.
TOOLS AND MATERIALS:
Plumbers
Tape
Adjustable
Wrench
Phillips
Screwdriver
1Hollyn Push-Button Shower Installation Instructions
Tape Measure
Drill
Hex Wrench
Wood Blocking
Soldering Kit
(for copper pipe)
½” Test Plug
Level
Pencil or
Marker
Hacksaw
HOLLYN PUSH-BUTTON SHOWER SYSTEM
VALVE INSTALLATION
3. Wrap the pipe couplings with plumber’s tape and
connect them to the valve body.
1. To prepare for installation, wood blocking should be
installed between the two studs where the valve will
mount. Be careful not to set the valve too far back into
the wall. Use the sticker on the side of the valve for
guidance.
Important: Take into consideration the thickness of
the finished wall materials, such as tile, when calculating
measurements.
2. The valve’s first joint contains an upper and lower
outlet. Wrap the provided plug with plumber’s tape and
plug one of the two outlets indicated in the diagram
below. Plug the outlet that will not be used.
2Hollyn Push-Button Shower Installation Instructions
4. Connect the inlet and outlet pipes as shown in the
diagram below.
plumber’s
tape
plug
first outlet
valve body
pipe coupling
outlet
inlet
HOLLYN PUSH-BUTTON SHOWER SYSTEM
6. Drill holes at each of the six marked mounting hole
locations using an 8 mm drill bit.
5. Use a level to adjust the valve body. Mark the location
of the mounting holes on the wood blocking.
3Hollyn Push-Button Shower Installation Instructions
8. Use a level to ensure that the valve is mounted
straight. Make adjustments as needed.
7. Insert the provided anchors into each of the drilled
holes. Affix the valve using self-tapping screws.
anchor
self-tapping
screws
HOLLYN PUSH-BUTTON SHOWER SYSTEM
11. Plug the outlets and open the two switches on the
left. Flush the water and check for leaks. Then, replace
the protective cover.
9. Flush the water lines to get rid of any dirt or debris,
then connect the water feed lines. Hot water should be
connected to the upper inlet, cold water to the lower
inlet.
4Hollyn Push-Button Shower Installation Instructions
12. Proceed to the installation of your wall and all
finished wall materials, including tile.
hot water
cold water
10. Remove the protective cover from the valve body.
turn on the switch. Flush the water and check for any
leaks.
switch
cap
protective
cover
flush water
flush water
switch closed
Slightly shake the cap on
the switch. If it is loose, then
the switch is closed. If tight,
then it is open.
flush water
flush water
switch open
hand shower
outlet
protective
cap
cut opening to remove
cap and connect hand
shower later.
plug
cut opening for valve.
leave room on all sides
for future maintenance.
reference lines for
finished wall
this side against
wall
front side
positioning
bar
upper surface
of cap
threaded adapter
this side against
wall
upper surface of cap even
with front side of positioning bar
HOLLYN PUSH-BUTTON SHOWER SYSTEM
15. Replace with shorter adjustable threaded adapters
and caps.
13. Remove all protective covers and caps once the
finished wall is completed.
5Hollyn Push-Button Shower Installation Instructions
16. With the switch open, place the positioning bar
against the wall as shown. Adjust the cap heights so
that they align with the front side of the positioning bar.
14. With the switch open, place the positioning bar
against the wall as shown. If the upper surface of the
cap is lower than the front side of the positioning bar,
adjust the cap height so that it is even with the front
side. Then, do as shown in step 17. If the upper surface
of the cap is higher than the front side of the positioning
bar, do as shown in step 15.
protective
cover
shorter threaded
adapters
HOLLYN PUSH-BUTTON SHOWER SYSTEM
17. Place the trim plate onto the installed valve body.
Wrap the hand shower’s threaded adapter with plumb-
er’s tape and thread it into its outlet.
6Hollyn Push-Button Shower Installation Instructions
19. Attach the control handle to the installed valve body.
Ensure that the slot mark on the spindle, the stop collar,
the safety button, and the 38°C mark are all aligned.
Tighten the M4 screw then insert the screw cap.
18. Test the buttons to ensure they are working
properly with the fitment of the trim plate. When a
button is pressed, it should extend approximately 1/4”
from the trim plate.
trim plate
threaded
adapter
button
handle
safety button
spindle
cartridge
slot mark
stop collar
slot (only visible when
the handle is off)
20. Install the hand shower cradle.
hand shower
cradle
set screw
SHOWER HEAD INSTALLATION
1. To prepare for installation, wood blocking should be
installed between the two studs where the valve will
mount. Be careful not to set the valve too far back into
the wall. Use the sticker on the side of the valve for
guidance.
Important: Take into consideration the thickness of
the finished wall materials, such as tile, when calculating
measurements.
2. Apply plumber’s tape to the threads of the two plugs,
straight connector, and pipe elbow. Screw the two plugs,
straight connector, and pipe elbow into the shower
holder as shown.
Shower holder
Elbow
Plumber’s tape
Straight Connector
Plug
HOLLYN PUSH-BUTTON SHOWER SYSTEM
21. Connect the hand shower and hose to the cradle.
7Hollyn Push-Button Shower Installation Instructions
22. Test the functionality of the hand shower. Check for
any leaks.
hose
hand shower
HOLLYN PUSH-BUTTON SHOWER SYSTEM
8Hollyn Push-Button Shower Installation Instructions
3. Use the four holes on the shower holder as a guide to
mark mounting hole locations on the wall, as shown in
the diagram below. Use a level to ensure an even
installation.
4. At each of the four marked mounting hole locations,
drill an 8mm diameter hole.
Pencil
6. Tighten screws and use the level to ensure the
shower holder remains straight, as shown in the
diagram below.
5. Insert an anchor into each of the four drilled
mounting holes, then affix the shower holder to the
wall using self-tapping screws.
Self-tapping screw
Phillips screwdriver
Anchor
HOLLYN PUSH-BUTTON SHOWER SYSTEM
9Hollyn Push-Button Shower Installation Instructions
8. Put on the protective cover, as shown.
7. Clean pipes to get rid of dirt and turn on water to test
pressure. Then, check for leaks.
Protective cover
9. Use the pipe bracket as a guide to mark the two
mounting hole locations on the wall, as shown in the
diagram below.
10. At both of the marked mounting hole locations,
drill an 8mm diameter hole. Then, insert the anchors
into the two holes.
Pipe bracket
Reinforcing rod
HOLLYN PUSH-BUTTON SHOWER SYSTEM
10Hollyn Push-Button Shower Valve Installation Instructions
11. Attach the bracket to the wall using self-tapping
screws.
12. Proceed to wall installations, including tile. Use
markings on the protective cover for guidance.
IMPORTANT: COMPLETE THE CONSTRUCTION OF
YOUR WALL, INCLUDING ANY FINISHED WALL
MATERIALS SUCH AS TILE, BEFORE PROCEEDING
WITH THE REMAINDER OF THE INSTALLATION.
STOP
13. Pull off the protective cover and unscrew the two
plugs.
HOLLYN PUSH-BUTTON SHOWER SYSTEM
11Hollyn Push-Button Shower Installation Instructions
Filtering net
Pipe nipple
14. Wrap plumbers tape around the pipe nipples and
screw them into the wall.
15. Attach the shower head to the wall. Then, fasten
with the M6 screw.
1. Apply plumber’s tape to the threads of the two plugs,
straight connector, and pipe elbow. Screw the two
plugs, straight connector, and pipe elbow into the
shower holder as shown.
16. After installation, run the water to remove any
debris or dirt.
INSTALLATION: WAY 2
Shower holder
Elbow
Plumber’s tape
Straight Connector
Plug
2. Attach the mounting plate to the plug and tighten
with a S7 wrench. Then, put on the protective cover
over the plug.
3. Use the four holes on the shower holder and the four
holes on the mounting plate as a guide to mark mount-
ing hole locations on the wall, as shown in the diagram
below. Use a level to ensure an even installation.
Mounting plate
Plug
Protective Cover
5. Insert an anchor into each of the drilled mounting
holes, then affix the mounting plate to the wall using
self-tapping screws.
4. At each of the marked mounting hole locations, drill
an 8mm diameter hole.
Hole
Drill
Slot
Rough wall
Self-tapping screw
Phillips screwdriver
Anchor
HOLLYN PUSH-BUTTON SHOWER SYSTEM
12Hollyn Push-Button Shower Installation Instructions
6. To ensure an even installation use a level, then tighten
the shower holder and locating plate.
7. To test the pressure, turn on the water and make
sure there are no leaks.
Horizontal alignment
9. At both of the marked mounting hole locations, drill an
8mm diameter hole. Then, insert the anchors into the two
holes.
8. Use the pipe bracket as a guide to mark the two mount-
ing hole locations on the wall, as shown in the diagram
below.
Reinforcing rod
Pipe bracket
Hole
HOLLYN PUSH-BUTTON SHOWER SYSTEM
13Hollyn Push-Button Shower Installation Instructions
10. Attach bracket to wall using self-tapping screws.
11. Fill in the slot with cement and proceed to wall installa-
tion, including tile.
Cement
IMPORTANT: COMPLETE THE CONSTRUCTION OF
YOUR WALL, INCLUDING ANY FINISHED WALL
MATERIALS SUCH AS TILE, BEFORE PROCEEDING
WITH THE REMAINDER OF THE INSTALLATION.
STOP
12. Pull off the protective cover and unscrew the two plugs.
HOLLYN PUSH-BUTTON SHOWER SYSTEM
14Hollyn Push-Button Shower Installation Instructions
15Hollyn Push-Button Shower Installation Instructions
15. After installation, run the water to remove any
debris or dirt.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15

Signature Hardware 443752 Installation guide

Signature Hardware
Brand
Signature Hardware
Model
443752
Category
Sanitary ware
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents