Metrologic MS1633 User manual

METROLOGIC INSTRUMENTS, INC.

MS1633 FocusBT

™

with

Bluetooth

®

Wireless Technology

Area Imaging Bar Code Scanner

Installation and User’s Guide

Copyright

work may be reproduced, transmitted, or stored in any form or by any means

without prior written consent, except by reviewer, who may quote brief

passages in a review, or provided for in the Copyright Act of 1976.

Trademarks

Metrologic is a registered trademark of Metrologic Instruments, Inc.

Products identified in this document are hereby acknowledged as

trademarks, registered or otherwise, of Metrologic Instruments, Inc. or their

respective companies.

The Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc.

and any use of such marks by Metrologic Instruments, Inc. is under license.

Other trademarks and trade names are those of their respective owners.

ii

TABLE OF CONTENTS

Introduction

Product Overview ............................................................................................. 1

Scanner and Accessories................................................................................. 2

Scanner Components....................................................................................... 3

Labels............................................................................................................... 4

Maintenance..................................................................................................... 5

Getting Started

Battery Tips and Cautions ................................................................................ 6

Charger Status Indicators................................................................................. 6

Charging the Battery ........................................................................................ 7

Battery Installation............................................................................................ 8

Low Battery Warning ........................................................................................ 8

Removing the Battery for Charging .................................................................. 8

Driver Installation

Driver Installation for USB Adapter with Bluetooth Technology........................ 9

Auto Reconnect Driver Setup......................................................................... 12

FocusBT Connection Configuration................................................................ 14

Establishing Communication via Bluetooth Technology

When FocusBT Acts as a Server to Other Devices........................................ 16

When FocusBT Acts as a Client to Other Devices ......................................... 17

When FocusBT is Used with an MS9535 Cradle............................................ 18

Range Gate Mode .......................................................................................... 18

Inventory Mode............................................................................................... 19

Stand Kits

Stand Components, MLPN 46-00147............................................................. 20

Hard Mounting the Stand................................................................................ 21

Assembling the Stand .................................................................................... 22

iii

TABLE OF CONTENTS

Scanner Operation

Two Default Modes of Operation.................................................................... 23

Audible Indicators........................................................................................... 24

Visual Indicators ............................................................................................. 25

Failure Modes................................................................................................. 26

Depth of Field by Minimum Bar Code Element Width .................................... 27

IR Activation Range........................................................................................ 28

Troubleshooting Guide ....................................................................................... 29

Design Specifications ......................................................................................... 33

Default Settings – Communication Parameters.................................................. 35

Configuration Modes .......................................................................................... 37

Upgrading the Flash ROM Firmware.................................................................. 38

Limited Warranty ................................................................................................ 39

Regulatory Compliance

Safety ............................................................................................................. 40

EMC ............................................................................................................... 41

Patents ............................................................................................................... 43

Index .................................................................................................................. 44

Contact Information and Office Locations........................................................... 46

1

INTRODUCTION

Product Overview

FocusBT™ is an Area Imager enabled with Bluetooth

®

wireless technology that

outperforms the competition by integrating advanced features to both hand-held

and presentation mode scanning such as FirstFlash

®

scanning, automatic aim

line, object detection and RangeGate

®

to optimize efficiency and productivity

while providing the freedom of mobility.

FocusBT has been designed with a removable battery pack for remote charging

to decrease down time caused by having a dead battery. Two battery packs are

supplied so the user can simultaneously scan while remotely charging the spare

battery. The benefits of this feature are 24/7 scanning and increased throughput

for all enterprise applications.

FocusBT is the industry leader in Area Imaging and the added benefits of

Bluetooth technology along with a rich feature set, make it the scanner of choice

for 2D wireless applications.

FocusBT

™

Interface

MS1633 – 5

BT Interface 1.2

Bluetooth technology Profile Supported:

SPP (Serial Port Profile)

Decoding and functional capability of the unit is restricted through the

use of license numbers provided by Metrologic. Units will not support

key features such as, but not limited to, the ability to decode PDF, 2D or

OCR fonts without the proper licenses. Desired licenses can be

specified at the time of sale or call a Metrologic representative for more

information. Standard models ship with the ability to read all 1D, PDF

and 2D bar codes. OCR fonts are disabled by default and must be

specifically requested at an additional cost.

www.metrologic.com 2

INTRODUCTION

Scanner and Accessories

BASIC KIT

Part # Description Qty.

MS1633 MS1633 FocusBT Area Imaging Bar Code Scanner 1

70-72018 Li-Ion Battery Pack 2

46-00358 Battery Charger 1

00-05176 USB BT adaptor 1

00-02544 MetroSelect

®

Single-Line Configuration Guide* 1

00-02281 Supplemental Configuration Guide* 1

46-00374 Software CD 1

00-02280 MS1633 FocusBT Installation and User’s Guide* 1

* Available on the Metrologic website - www.metrologic.com

OPTIONAL ACCESSORIES

Part # Description

AC to DC Power Transformer - 5.2VDC @ 2 A output.

46-46915 120V United States

46-46913 220V-240V Continental European

46-46912 220V-240V United Kingdom

46-46914 220V-240V Australia

46-46911 220V-240V China

00-02001 MS1633 Focus Stand (46-00147) Installation Guide

46-00147 Modular Presentation Stand

Other items may be ordered for the specific protocol being used. To order additional items,

contact the dealer, distributor or call Metrologic’s Customer Service Department at

1-800-ID-METRO or 1-800-436-3876.

3

INTRODUCTION

Scanner and Charger Components

Figure 1. Scanner and Charger Components

Item Description

1 Yellow LED See Visual Indicators (on page 25)

2 White LED See Visual Indicators (on page 25)

3 Blue LED See Visual Indicators (on page 25)

4 Speaker See Audible Indicators (on page 24)

5 Trigger

6 Red Window LED Aperture

7 Power Button See Charging the Battery (on page 8)

8 Blue Power LED See Charging the Battery (on page 7)

9 Battery Pack See Battery Installation (on page 8)

10 Lock See Battery Installation (on page 8)

11 Power Jack See Battery Installation (on page 8)

12 Charging Contacts See Battery Installation (on page 7)

13 Blue Power LED See Charger Status Indicators (on page 6)

14 White Charge LED See Charger Status Indicators (on page 6)

www.metrologic.com 4

INTRODUCTION

Labels

Each scanner has a label located on the underside of the head. This label

provides the unit’s model number, date of manufacture, serial number, CE and

caution information. The charger, the USB Adapter and the battery also have

labels with important safety and compliance information. The following figure

provides examples of these labels and their locations.

Figure 2. Label Locations and Samples

Caution:

To maintain compliance with applicable standards, all circuits connected to the scanner must

meet the requirements for SELV (Safety Extra Low Voltage) according to EN/IEC 60950-1.

To maintain compliance with standard CSA-C22.2 No. 60950-1/UL 60950-1 and norm

EN/IEC 60950-1, the power source should meet applicable performance requirements for a

limited power source.

5

INTRODUCTION

Maintenance

Smudges and dirt on the unit's window can interfere with the unit's performance.

If the window requires cleaning, use only a mild glass cleaner containing no

ammonia. When cleaning the window, spray the cleaner onto a lint free, non-

abrasive cleaning cloth then gently wipe the window clean.

If the unit's case requires cleaning, use a mild cleaning agent that does not

contain strong oxidizing chemicals. Strong cleaning agents may discolor or

damage the unit's exterior.

www.metrologic.com 6

GETTING STARTED

Battery Tips and Cautions

Before the FocusBT can be placed in operation the battery pack must be

charged for a minimum of 8 hours. After the initial preparation charge of

8 hours, the battery will only require 6 hours to come to a full charge when it

gives a Low Battery warning (see page 8). Follow the steps on page 7 to fully

charge the battery.

Once charged, the unit is able to handle 5400 continuous first pass readings over

a period of approximately 9 hours. After 30 seconds of no activity the scanner

will go into a sleep mode to conserve battery life.

Caution

Observe proper precautions when handling batteries.

Batteries may leak or explode if improperly handled. Observe the following

precautions when handling batteries for use in this product:

• Be sure the battery is turned off before replacing the battery.

• Be sure the battery is turned off when installed in the charger.

• Use only batteries approved for use in this equipment.

Do not mix old and new batteries or batteries of different types.

• Do not attempt to insert the battery upside down or backwards.

• Do not short or disassemble the battery.

• Do not expose the battery to flame or excessive heat.

• Do not immerse the battery in water or expose it to water.

• Do not transport or store with metal objects such as necklaces or hairpins.

• Batteries are prone to leakage when fully discharged.

To avoid damage to the product, be sure to remove the battery when no

charge remains.

• When not in use store the battery in a cool dry place.

• Discontinue use immediately should you notice any changes in the

battery, such as discoloration or deformation.

• Please recycle used batteries in accordance with local regulations.

Charger Status Indicators

There are two status indicators on the front of the charger located under the

Metrologic Logo. The following table lists how these indicators will illuminate

depending on the status of the charger.

CHARGER STATUS BLUE LED (PW) WHITE LED (CH)

Charging On Blinking

Fully Charged On Solid

Power On On OFF

Power Off OFF OFF

7

Figure

3

Figure 4

Figure 5

Figure 6

GETTING STARTED

Charging the Battery

Before the FocusBT can be placed in operation for the first time, the battery

must be charged for a minimum of 8 hours. After the initial preparation

charge of 8 hours, the battery will only require 6 hours to come to a full charge

when it gives a Low Battery warning (see page 8).

1. Check the AC input requirements of the

power supply to make sure the voltage

matches the AC outlet. The outlet

should be located near the charger and

easily accessible.

2. Plug the power supply into the socket

on the back of the charger.

A blue PW will illuminate near the

Metrologic logo indicating the charger is

receiving power.

3. Verify that the battery pack is not ON.

The blue power LED on the battery pack

should be OFF.

Warning!

Damage to the battery pack

can occur if it is charged while

turned ON.

4. Insert the battery pack into the charger

as shown in Figure 5.

A white CH will start to flash on and off

on the charger near the Metrologic logo.

If the white CH does not appear,

check to make sure the battery pack

is seated all the way in the charger

with the battery contacts facing the

contacts on the charger.

5. When the battery is completely

charged the charging indicator

(CH) will stop flashing and stay

illuminated.

www.metrologic.com 8

GETTING STARTED

Battery Installation

MS1633 FocusBT is a battery powered scanner. Before the FocusBT can be

placed in operation for the first time, the battery must be charged for a

minimum of 8 hours.

To install the battery:

1. Align the tabs of the charged battery pack with the slots on the scanner’s

handle

2. Then, slide the battery pack up toward the top of the scanner. There will be

a snap when the battery is installed correctly.

Figure 7. Steps for Installing the Battery

Low Battery Warning

When the battery is low the unit will add an additional beep after the good scan

beep. The additional beep alerts the user when there is less than 10% of a

charge left on the battery.

Removing the Battery for Charging

In order to charge the battery, it must be disconnected from the scanner.

1. Turn off the battery by pressing the button near the base of the battery.

2. Disengage the lock on end of the scanner handle (see below).

3. Slide the battery pack down away from the head of the scanner.

4. Lift the battery straight off the scanner handle (see below).

Figure 8. Steps for Removing the Battery for Charging

9

DRIVER INSTALLATION

Driver Installation for USB Adapter with Bluetooth Technology

1. Load the included FocusBT CD into the CD-ROM drive on the

host/computer.

2. If the CD-ROM does not automatically open, click on the Window’s Start

button, choose Run, then click Browse to locate and open the CD-ROM

drive. Double-Click on the Metrologic.exe file then click OK.

3. Click on the MetroBT Driver button to begin installation.

Figure 9.

4. Choose a Setup Language then click OK.

Figure 10.

www.metrologic.com 10

DRIVER INSTALLATION

Driver Installation for USB Adapter with Bluetooth Technology

5. At the welcome screen select Next.

Figure 11.

6. After reviewing the end user license agreement, select the, “I accept the

terms in the license agreement” option then, click Next to continue.

Figure 12.

7. Choose Install from the Ready to Install the Program screen.

Figure 13.

11

DRIVER INSTALLATION

Driver Installation for USB Adapter with Bluetooth Technology

8. To continue the installation procedure without showing warnings for

unauthorized drivers, select I accept and click OK.

Figure 14.

9. Plug the Bluetooth USB Adapter into the host device then click OK to

indicate the Bluetooth Adapter has been connected.

Figure 15.

10. After the installation completes click on Yes to restart the host

device/computer. The host/computer must be rebooted at this time in order

for the driver to function properly.

Figure 16.

www.metrologic.com 12

DRIVER INSTALLATION

Auto Reconnect Driver Setup

1. Load the included FocusBT CD into the CD-ROM drive on the

host/computer.

2. If the CD-ROM does not automatically open, click on the Window’s Start

button, choose Run, then click Browse to locate and open the CD-ROM

drive. Double-Click on the Metrologic.exe file then click OK.

3. Click on the MetroBT Utility button to begin installation.

Figure 17.

4. Click OK to continue.

Figure 18.

5. Locate the COMReConnect icon on the Windows desktop and double click

to open the program.

Figure 19.

13

DRIVER INSTALLATION

Auto Reconnect Driver Setup

6. The Auto Reconnect Utility will automatically start if any of the COM ports

with Bluetooth technology are checked. When running, the utility window will

look like the figure below.

Clicking the “X” in the corner of the window or clicking on the close button

will disable the auto-reconnect feature. However, if the Place icon in the

taskbar option is checked, the utility will remain active after the window is

closed.

Figure 20.

www.metrologic.com 14

Figure 21.

DRIVER INSTALLATION

FocusBT Connection Configuration

1. Double-Click on the Bluetooth icon located on the

Windows Start bar in the bottom right corner of the

screen.

2. The new connection wizard will automatically start.

Power up the FocusBT scanner and allow it to boot completely

Three beeps will indicate the scanner is completely booted.

Select Express Mode then click Next.

Figure 22.

3. A search for Bluetooth wireless technology devices should find the FocusBT.

The number(s) next to FocusBT indicate the serial number of the unit(s)

found.

Select the proper device and click Next to continue.

Figure 23.

15

DRIVER INSTALLATION

FocusBT Connection Configuration

4. The final screen of the New Connection Wizard should indicate the virtual

Bluetooth Com port that was setup. This will usually be a high number, as

seen in the screen shot below. Remember this COM number for

application setup.

Click Next to Continue.

Figure 24.

5. After the FocusBT has been added to the connection list, right click on the

icon and select Connect in order to establish a link via Bluetooth technology

between the FocusBT and your computer.

The FocusBT should emit a connection tone and/or the blue light on the top

of the unit should stop blinking, indicating a connection has been

established.

Figure 25.

www.metrologic.com 16

ESTABLISHING COMMUNICATION VIA BLUETOOTH TECHNOLOGY

Communication via Bluetooth wireless technology must be established

between the FocusBT and the host device before the FocusBT can be used

for normal operation.

In a network with Bluetooth technology, the FocusBT can operate as a server

(service-provide mode), or as a client.

When FocusBT Acts as a Server to Other Devices with

Bluetooth Technology

FocusBT’s default is to act as a server to other devices with Bluetooth

technology. In this mode, other devices enabled with Bluetooth wireless

technology can initiate a connection to the scanner.

FocusBT can be configured to always accept incoming connection requests and

not require a valid Bluetooth PIN. Alternatively, FocusBT can be configured to

require a valid Bluetooth PIN. In this case, the PIN used by a remote device while

establishing connection to the FocusBT, must match the one previously stored in

FocusBT.

*Bluetooth PIN Not Required Bluetooth PIN Required

³124306

³124316

To store a Bluetooth PIN

The FocusBT can be configured to store a Bluetooth PIN so that any remote

device trying to establish a connection with the scanner, must match the stored

PIN before a connection will made. The stored PIN must be numeric and be

between 4 to 16 digits long. A PIN that does not satisfy the criteria will not be

stored.

After scanning the following bar code, the next bar code scanned will be stored

and used as the Bluetooth PIN. This feature is used in conjunction with the

Bluetooth PIN required feature.

Next bar code is Bluetooth PIN

³999918

Scanning the Recall Defaults bar code resets the PIN to the default

value of 0000.

Page is loading ...

Metrologic MS1633, FocusBT 1633, MS1633 FocusBT User manual

Related papers

Other documents