Profile Design HSF BTA Drink System Tilt Wedges Operating instructions

Type
Operating instructions

Profile Design HSF BTA Drink System Tilt Wedges are a set of plastic wedges designed to be used with standard spaced (64mm) bottle cages and BTA mounts. They allow you to adjust the angle of your bottle cage to improve your riding comfort and efficiency. The wedges are made of a durable plastic material and come with all the necessary hardware for installation.

To install the wedges, simply choose the number of wedges required, either by measuring the angle of the mount or test fitting. Mount the first wedge to the BTA mount using two of the countersunk bolts and torque to 3Nm. Each successive wedge is mounted to the one below using two countersunk bolts torqued to 3Nm. Once you have achieved the desired angle, mount the bottle cage to the uppermost wedge using the bolts supplied with the cage, with the washer underneath the front bolt and torque to 3Nm.

Profile Design HSF BTA Drink System Tilt Wedges are a set of plastic wedges designed to be used with standard spaced (64mm) bottle cages and BTA mounts. They allow you to adjust the angle of your bottle cage to improve your riding comfort and efficiency. The wedges are made of a durable plastic material and come with all the necessary hardware for installation.

To install the wedges, simply choose the number of wedges required, either by measuring the angle of the mount or test fitting. Mount the first wedge to the BTA mount using two of the countersunk bolts and torque to 3Nm. Each successive wedge is mounted to the one below using two countersunk bolts torqued to 3Nm. Once you have achieved the desired angle, mount the bottle cage to the uppermost wedge using the bolts supplied with the cage, with the washer underneath the front bolt and torque to 3Nm.

HSF BTA Wedges
1
HSF BTA WEDGES
REVISION 01-05-25-2022
HSF BTA Wedges
1
Thank you for purchasing this set of Profile Design HSF BTA Wedges.
Note to Dealers: If you install this product for the consumer, please provide him/her with this owner’s manual after installation.
Please read these instructions thoroughly before attempting to install this item. Proper installation is required for compliance with Profile Design's
warranty policy. If you are not familiar with installing bicycle accessories, please seek the assistance of your local Profile design dealer by logging on to
www.profile-design.com and using "dealer search" or by calling Profile Design's customer service number p.# 888.800.5999.
Tools and materials required:
Your Cage kit should contain:
Components compatible with this Wedge:
• 3mm Hex wrench
• Three (3) plastic wedges (5°)
• Six (6) M5x10 countersunk steel bolts with preinstalled threadlocker
• One (1) washer
• Any standard spaced (64mm) bottle cage
• Any standard spaced (64mm) BTA mount
INTRODUCTION
WARNING: Periodically check the Wedge for damage, particularly for cracks or scratches in the surface that could lead to degradation and weakening
of the base material. Replace any component on which you notice any damage from use or accident.
If anything is missing from the wedge kit please contact your dealer.
HSF BTA Wedges
2
01
0302
COMPONENT LIST
Part.# Part Description
274473 HSF BTA Wedges (5 degree)
313602 Bolt - M5x10mm FHB w/Nylok
275674 Washer 6x12x1.5 UCP
QTY.
Req.
3
6
1
Ref.#
1
2
3
HSF BTA Wedges
3
PART DRAWINGS
124.8 mm
64 mm 20.5 mm
14.8 mm 15 mm
HSF BTA Wedges
4
INSTALLATION INSTRUCTIONS
1. Choose the number of wedges required, either by measuring the angle of the mount or test fitting.
2. Mount the first wedge to the BTA mount using two of the countersunk bolts and torque to 3Nm.
• Do not grease the bolts as this will neutralise the threadlocker.
3. Each successive wedge is mounted to the one below using two countersunk bolts torqued to 3Nm.
4. Once you have achieved the desired angle, mount the bottle cage to the uppermost wedge using the bolts supplied with the cage, with the washer
underneath the front bolt and torque to 3Nm.
HSF BTA Wedges
5
• Profile Design Worldwide Two Year Limited Warranty.
Profile Design, LLC (distributor) warrants to the original retail purchaser ("you") that the Profile Design product for which you received
this warranty is free from defects in material and workmanship for (2) two years from the date of original retail purchase. For more
details on this warranty, its exclusions and/or how to make a claim under the warranty please call +1 310.747.0085 extension 161 or visit
www.profile-design.com/pages/warranty
WARNING
HSF BTA Wedges
6
2677 El Presidio Street
Long Beach, CA 90810
Ph: 310-884-7756
w
ww.profile-design.com
© Profile Design LLC
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7

Profile Design HSF BTA Drink System Tilt Wedges Operating instructions

Type
Operating instructions

Profile Design HSF BTA Drink System Tilt Wedges are a set of plastic wedges designed to be used with standard spaced (64mm) bottle cages and BTA mounts. They allow you to adjust the angle of your bottle cage to improve your riding comfort and efficiency. The wedges are made of a durable plastic material and come with all the necessary hardware for installation.

To install the wedges, simply choose the number of wedges required, either by measuring the angle of the mount or test fitting. Mount the first wedge to the BTA mount using two of the countersunk bolts and torque to 3Nm. Each successive wedge is mounted to the one below using two countersunk bolts torqued to 3Nm. Once you have achieved the desired angle, mount the bottle cage to the uppermost wedge using the bolts supplied with the cage, with the washer underneath the front bolt and torque to 3Nm.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI