Dynojet PC6-20061 Installation guide

PC6-20061
Dynojet
Brand
Dynojet
Model
PC6-20061
Type
Installation guide

Dynojet PC6-20061 is a versatile fuel management system designed to enhance the performance of your 2019-2022 Suzuki RMZ250. With its ability to store and switch between two maps on the fly, you can optimize your bike's performance for different conditions or riding styles. The PC6-20061 also features inputs for accessories like a quick shifter, speed sensor, analog input for engine temp or boost, and a launch control switch. This allows you to fine-tune your bike's performance and improve your riding experience.

Dynojet PC6-20061 is a versatile fuel management system designed to enhance the performance of your 2019-2022 Suzuki RMZ250. With its ability to store and switch between two maps on the fly, you can optimize your bike's performance for different conditions or riding styles. The PC6-20061 also features inputs for accessories like a quick shifter, speed sensor, analog input for engine temp or boost, and a launch control switch. This allows you to fine-tune your bike's performance and improve your riding experience.

1 POWER COMMANDER 6
1 INSTALLATION GUIDE
1 USB CABLE
2 DYNOJET DECALS
2 POWER COMMANDER DECALS
2 VELCRO STRIPS
1 ALCOHOL SWAB
1 POSI-TAP
PARTS LIST
PLEASE READ ALL DIRECTIONS BEFORE STARTING INSTALLATION.
THE IGNITION MUST BE TURNED OFF BEFORE INSTALLATION.
IPC6-20061.01
POWER COMMANDER 6
Installation Guide for: PC6-20061
Model Coverage: 2019-2022 Suzuki RMZ250
2 2019-2022 SUZUKI RMZ250 2 PC6-20061
INPUT ACCESSORY GUIDE
Map (Input 1 or 2) The PC6 has the ability to hold 2 different base maps. You can switch on the fly between these two
base maps when you hook up a switch to the MAP inputs. You can use any open/close type switch. The polarity of
the wires is not important.
Shifter (Input 1 or 2) Used for clutch-less full throttle upshifts. Insert the wires from the Dynojet quick shifter into either
Input 1 or Input 2. The polarity of the wires is not important. Set to Input 2 by default.
Speed If your application has a speed sensor then you can tap into the signal side of the sensor and run a wire into this
input. This will allow you to calculate gear position in the Control Center Software. Once gear position is setup
you can alter your map based on gear position and setup gear dependent kill times when using a quick shifter.
Analog This input is for a 0-5v signal such as engine temp, boost, etc. Once this input is established you can alter your
fuel curve based on this input in the Power Core software.
Launch You can connect a wire to either Input 1 or Input 2 and then the other end to a switch. This switch when engaged
(continuity) will only allow the RPM to be raised to a certain limit (set in the software). When released, you will
have full RPM.
OPTIONAL ACCESSORY INPUTS
WIRE CONNECTIONS
To input wires into the PC6 first remove the rubber plug on the backside of
the unit and loosen the screw for the corresponding input. Using a 22-24
gauge wire, strip about 10mm from its end. Push the wire into the hole of
the PC6 until it stops and then tighten the screw. Make sure to reinstall
the rubber plug.
NOTE: If you tin the wires with solder it will make inserting them easier.
SPEED
INPUT 2
INPUT 1
EXPANSION
PORTS 1 & 2
USB
CONNECTION
CRANK
ANALOG
INPUT 2
INPUT 1
3 PC6-20061
1 Remove the seat, the radiator shrouds, and the fuel
tank.
2 Secure the PC6 module to the outside of the right
side frame rail just rear of the radiator.
Use the supplied dual lock Velcro to secure the
module. Clean surfaces with the alcohol swab before
attaching the Velcro.
3 Secure the PC6 ground wire with the small ring
terminal to the frame using the stock common ground
bolt.
4 Locate and unplug the Primary Fuel Injector.
This injector is located on the bottom of the throttle
body.
INSTALLING THE POWER COMMANDER 6
4 2019-2022 SUZUKI RMZ250 4 PC6-20061
5 Plug the pair of PC6 wiring harness leads with
ORANGE colored wires in-line of the primary injector
and stock wiring harness.
6 Locate and unplug the Secondary Fuel Injector.
This injector is located on the bottom of the intake
plenum rear of the throttle body.
7 Plug the pair of PC6 wiring harness leads with
YELLOW colored wires in-line of the secondary
injector and stock wiring harness.
8 Pull back on the rubber boot covering the Throttle
Position Sensor connector to expose the stock TPS
wires.
5 PC6-20061
9 Use the supplied Positap
to attach the PC6 GREY
wire to the stock YELLOW
wire of the bike’s TPS.
Using a small dab of
dielectric grease on this
connection can help
prevent corrosion.
10 Pull the stock rubber boot
back over the connector to
protect the wires.
11 Reinstall the fuel tank,
bodywork, and the seat.
Download the latest map files from our web site at
dynojet.com/tunes.
© 2019-2022 DYNOJET RESEARCH ALL RIGHTS RESERVED
2191 MENDENHALL DRIVE, NORTH LAS VEGAS, NV 89081 - 800-992-4993 - DYNOJET.COM
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6

Dynojet PC6-20061 Installation guide

PC6-20061
Dynojet
Brand
Dynojet
Model
PC6-20061
Type
Installation guide

Dynojet PC6-20061 is a versatile fuel management system designed to enhance the performance of your 2019-2022 Suzuki RMZ250. With its ability to store and switch between two maps on the fly, you can optimize your bike's performance for different conditions or riding styles. The PC6-20061 also features inputs for accessories like a quick shifter, speed sensor, analog input for engine temp or boost, and a launch control switch. This allows you to fine-tune your bike's performance and improve your riding experience.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents