Altronix WP2 Installation guide

Type
Installation guide

Altronix WP2 is a NEMA 4/IP 66 Rated outdoor power supply/battery and accessory enclosure with a metal backplane. It can house various Altronix power supplies, sub-assemblies, and accessories, making it ideal for outdoor security and surveillance applications. Its durable construction and weatherproof design ensure reliable operation in harsh environments.

Altronix WP2 is a NEMA 4/IP 66 Rated outdoor power supply/battery and accessory enclosure with a metal backplane. It can house various Altronix power supplies, sub-assemblies, and accessories, making it ideal for outdoor security and surveillance applications. Its durable construction and weatherproof design ensure reliable operation in harsh environments.

WP2
Weatherproof Enclosure
Installation Guide
Rev. 070918 More than just power.TM
Installing Company: _______________ Service Rep. Name: __________________________________
Address: _____________________________________________ Phone #: __________________
- 2 - WP2
Overview:
Altronix WP2 is a UL Listed, NEMA 4/IP 66 Rated outdoor power supply/battery and accessory enclosure with
a metal backplane. It can accommodate a wide variety of Altronix power supplies, sub-assemblies, and other
accessories.
Specifications:
NEMA 4/4X, IP66-11 Rated enclosure for outdoor use.
Hot compression molded, halogen free, self extinguishing fiberglass reinforced polyester.
Stainless steel continuous hinge and stainless steel padlockable latches.
Includes metal backplane for mounting power supplies and accessories.
Integral flanges simplify wall or pole mounting.
Fits two (2) 12VDC/12AH batteries.
Product weight: 9 lb. (4.08 kg).
Shipping weight: 10.5 lb. (11.57 kg).
Installation Instructions:
1. Remove backplane inside enclosure by removing the four (4) mounting screws (do not discard hardware).
2. Mark and drill desired knockouts on the enclosure to facilitate wiring.
3. Enclosure can be wall or pole mounted. See the detailed instructions below.
4. Mount circuit boards to backplane.
5. Secure backplane inside the enclosure with the four (4) mounting screws.
6. Mount unit in desired location with the appropriate fasteners utilizing the holes provided on the flanges
(Enclosure Dimensions, pg. 4).
7. To facilitate wire entry utilize weather tight NEMA 4 rated connectors, bushings and cable.
WP2 - 3 -
Wall Mount Installation
1- Place unit at desired location and secure with mounting
screws (not included) (Fig. 1, pg. 3).
Fig. 1
Pole Mounting Using Optional Pole Mount Kit PMK2 (not included):
This installation should be made by qualified service personnel. This product contains no serviceable parts.
PMK2 is intended for use with Altronix outdoor rated power supplies or accessories housed in WP2 enclosures.
Brackets are designed for use with the Wormgear Quick Release Straps (two included).
1. Thread one (1) wormgear quick release strap through the slots on the back of a mounting bracket (Fig. 2).
2. Once the desired height of the top Pole Mount bracket is achieved, tighten the straps down by sliding open
end of the strap through the locking mechanism on the strap, then tighten the screw with flat head screwdriver
or 5/16” hex socket driver (Fig. 3).
3. Attach the bottom bracket to the enclosure by inserting bolts through the flange of the enclosure and into the
bracket, tightening bolts with a 7/16” hex socket (Fig. 4).
4. Thread the second wormgear quick release strap through the slots on the back of the bottom mounting
bracket (Fig. 5).
5. Mount enclosure onto the top bracket by inserting bolts through flange of the enclosure and into the bracket,
tightening bolts with a 7/16” hex socket (Fig. 6).
6. Tighten the straps of the bottom bracket down by sliding the open end of the strap through the locking
mechanism on the strap, then tighten screw with flat head screwdriver or 5/16” hex socket driver (Fig. 6/6a).
7. Clip excess straps.
Fig. 2 Fig. 3 Fig. 4
Fig. 5
Fig. 6
2” to 8”(50.8mm to 203.2mm)
diameter round pole
Fig. 6a
5” (127mm) square pole
- 4 - WP2
Altronix is not responsible for any typographical errors.
140 58th Street, Brooklyn, New York 11220 USA | phone: 718-567-8181 | fax: 718-567-9056
website: www.altronix.com | e-mail: [email protected] | Made in U.S.A.
IIWP2 G15U MEMBER
Enclosure Dimensions (H x W x D approximate):
17.53” x 15.3” x 6.67” (445.3mm x 388.6mm x 169.4mm)
FRONT VIEW COVER REMOVED
RIGHT SIDE VIEWFRONT VIEW
END VIEW
SECTION A-A
AA
316 STAINLESS STEEL PADLOCK LATCH
ATTACHED WITH RIVETS. Ø 0.375 PADLOCK EYE
17.36” (441 mm)
12.00” (304.8mm)
6.41” (162.8mm)
10-32 X 0.250 BRASS INSERT 4 PLCS.
14.54” (369.3mm)
16.74” (425.2mm)
0.125” (3.2mm)
14.25” (362mm)
14.00” (355.6mm)
12.23” (310.6mm)
17.53” (445.3mm)
16.00” (406.4mm)
1.67” (42.4mm) 5.00” (127mm)
16.73” (425mm)
15.3” (388.6mm)
6.67” (169.4mm)
4.94” (125.5mm)
5.77” (146.6mm)
0.75” (19.1mm)
MOUNTING PLATE
Ø 0.32” (8.1mm)
WALL MOUNTING HOLE X 4
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Altronix WP2 Installation guide

Type
Installation guide

Altronix WP2 is a NEMA 4/IP 66 Rated outdoor power supply/battery and accessory enclosure with a metal backplane. It can house various Altronix power supplies, sub-assemblies, and accessories, making it ideal for outdoor security and surveillance applications. Its durable construction and weatherproof design ensure reliable operation in harsh environments.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI