Hoymiles HT10 Installation guide

Brand: Hoymiles

Model: HT10

Type: Installation guide

Hoymiles HT10 is a rapid shutdown system that allows for the safe and efficient isolation of solar panels in the event of an emergency. It features two cores, each capable of handling up to 75A or 150A of current, allowing for a maximum of 15 strings per core. The HT10 is designed for use with Hoymiles inverters and requires a Din Rail PSU for power. It ensures compliance with rapid shutdown requirements by powering off the PV system when necessary. The Power LED1 indicates when the system is operating, while the Signal LED2 blinks to show communication.

Hoymiles HT10 is a rapid shutdown system that allows for the safe and efficient isolation of solar panels in the event of an emergency. It features two cores, each capable of handling up to 75A or 150A of current, allowing for a maximum of 15 strings per core. The HT10 is designed for use with Hoymiles inverters and requires a Din Rail PSU for power. It ensures compliance with rapid shutdown requirements by powering off the PV system when necessary. The Power LED1 indicates when the system is operating, while the Signal LED2 blinks to show communication.

HT10 Quick Installation Guide

1. Appearance

2. System Solution

© 2022 Hoymiles Power Electronics Inc. All rights reserved.

Single Core

Dual Core

Inverter

RSD

Transmitter

Inverter

Transmitter

RSD

Region: Global AP040559 REV1.1

L

N

GND

+12 V

Transmitter

Din Rail PSU

Core 1

LED 2

INITIATOR -

+12 V

GND

CORE 1

CORE 2

INITIATOR +

LED 1

LED 2

Core 2

L

N

GND

+12 V

LED 2

INITIATOR -

+12 V

GND

CORE 1

CORE 2

INITIATOR +

LED 1

LED 2

*Only positive homerun or negative

homerun through core

*Only positive homerun or negative

homerun through core

Note:

·Install HRSD before powering on Transmitter.

·Transmitter power supply must be on same AC branch circuit as

inverter to meet rapid shutdown requirements.

·When PV system is operating, the Power LED1 should be lit and the

Signal LED2 should be blinking.

·Place rapid shutdown system label no more than 1m (3ft) from

Transmitter or AC disconnect if not at the same location.

HT10 Quick Installation Guide

3. Installation

© 2022 Hoymiles Power Electronics Inc. All rights reserved.

Note:

·Max. number of strings per Core*: 5 (75A core) or 15 (150A core)

·Max. current per Core: 75A or 150A

·Max. cable length from inverter (+) to inverter (-): 1000ft (300m)

·Mount Transmitter and power supply on DIN rail.

·Connect DC leads from power supply to Transmitter.

·Connect Core to Transmitter. If there is only one core that needs to be connected, please connect Core 1 first.

·Pass either positive homerun or negative homerun through cores.

·Connect wires to AC side of power supply.

*Only positive homerun

or negative homerun

through core

*Only positive homerun

or negative homerun

through core

*Only positive homerun

or negative homerun

through core

1

2

* With Φ 6 mm DC cable diameter (without DC connector)

L

N

GND

+12 V

Transmitter

Din Rail PSU

Core 1

LED 2

INITIATOR -

+12 V

GND

CORE 1

CORE 2

INITIATOR +

LED 1

LED 2

Core 2

Region: Global AP040559 REV1.1

L

N

GND

+12 V

LED 2

INITIATOR -

+12 V

GND

CORE 1

CORE 2

INITIATOR +

LED 1

LED 2

Transmitter

Din Rail PSU

Core 1

1
2

Hoymiles HT10 Installation guide

Brand: Hoymiles

Model: HT10

Type: Installation guide

Hoymiles HT10 is a rapid shutdown system that allows for the safe and efficient isolation of solar panels in the event of an emergency. It features two cores, each capable of handling up to 75A or 150A of current, allowing for a maximum of 15 strings per core. The HT10 is designed for use with Hoymiles inverters and requires a Din Rail PSU for power. It ensures compliance with rapid shutdown requirements by powering off the PV system when necessary. The Power LED1 indicates when the system is operating, while the Signal LED2 blinks to show communication.

Related papers

Other documents