Hoymiles HT10 Installation guide

Type
Installation guide

Hoymiles HT10 is a rapid shutdown system designed to enhance the safety of your solar PV system. It enables you to quickly and safely shut down the system in the event of an emergency, such as a fire or grid failure. The system comprises a transmitter, cores, and a power supply unit. The transmitter communicates with the cores to initiate a rapid shutdown when necessary. The cores are connected to the PV strings and are responsible for interrupting the circuit. The power supply unit provides power to the transmitter and the cores.

Hoymiles HT10 is a rapid shutdown system designed to enhance the safety of your solar PV system. It enables you to quickly and safely shut down the system in the event of an emergency, such as a fire or grid failure. The system comprises a transmitter, cores, and a power supply unit. The transmitter communicates with the cores to initiate a rapid shutdown when necessary. The cores are connected to the PV strings and are responsible for interrupting the circuit. The power supply unit provides power to the transmitter and the cores.

HT10-Kit Quick Installation Guide
2. System Solution
© 2022 Hoymiles Power Electronics Inc. All rights reserved.
Inverter
Inverter
1. Appearance
Transmitter
Transmitter
RSD
RSD
Single Core
Dual Core
Region: Global AP040561 REV1.1
L
N
-12 V
+12 V
INITIATOR -
+12 V
GND
INITIATOR
+
LED 1
CORE
1
LED 2
LED 2
CORE
2
L
N
-12 V
+12 V
INITIATOR -
+12 V
GND
INITIATOR
+
LED 1
CORE
1
LED 2
LED 2
CORE
2
Transmitter
Din Rail PSU
Core 1
Core 2
* With Φ 6 mm DC cable diameter (without DC connector)
HT10-Kit Quick Installation Guide
© 2022 Hoymiles Power Electronics Inc. All rights reserved.
· Pass either positive homerun or negative homerun through Cores.
· Connect wires to AC side of power supply.
*Only positive
homerun or
negative homerun
through core
*The waterproof
accessories are not
supplied and need to be
prepared by the installer
*AC Wires for PSU
*Only positive
homerun or negative
homerun through
core
*Only positive
homerun or negative
homerun through
core
2
Note:
· Install HRSD before powering on Transmitter.
· Transmitter power supply must be on same AC branch circuit as
inverter to meet rapid shutdown requirements.
· When PV system is operating, the Power LED1 should be lit and the
Signal LED2 should be blinking.
· Place rapid shutdown system label no more than 1m (3ft) from
Transmitter or AC disconnect if not at same location.
Note:
· Max. number of strings per Core*: 5 (75A core) or 15 (150A core)
· Max. current per Core: 75A or 150A
· Max. cable length from inverter (+) to inverter (-): 1000ft (300m)
3. Installation
· Mount Transmitter and power supply on DIN rail.
· Connect DC leads from power supply to Transmitter.
· Connect Core to Transmitter. If there is only one core
need to connect, please connect Core 1 first.
Note:
· 85-264VAC or 180-550VAC PSU can be used.
· 180-550VAC PSU isolation class I requires grounding.
· 85-264VAC PSU isolation class II does not require
grounding.
Region: Global AP040561 REV1.1
1
L
N
-12 V
+12 V
INITIATOR -
+12 V
GND
INITIATOR
+
LED 1
CORE
1
LED 2
LED 2
CORE
2
L
N
-12 V
+12 V
INITIATOR -
+12 V
GND
INITIATOR
+
LED 1
CORE
1
LED 2
LED 2
CORE
2
Transmitter
Din Rail PSU
Core 1
Core 2
  • Page 1 1
  • Page 2 2

Hoymiles HT10 Installation guide

Type
Installation guide

Hoymiles HT10 is a rapid shutdown system designed to enhance the safety of your solar PV system. It enables you to quickly and safely shut down the system in the event of an emergency, such as a fire or grid failure. The system comprises a transmitter, cores, and a power supply unit. The transmitter communicates with the cores to initiate a rapid shutdown when necessary. The cores are connected to the PV strings and are responsible for interrupting the circuit. The power supply unit provides power to the transmitter and the cores.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI