ETS 5465 User manual

Brand: ETS

Model: 5465

Type: User manual

ETS 5465 Dry Gas Dehumidification System is specifically designed to work with ETS 5112 or 5100/5200 Series Automatic Humidity Controllers. It can be used with both the 5506A chamber and non-acrylic chambers. The system includes a solenoid valve, power cord, 10 feet of ¼” OD Polytubing, and mounting hardware. Using the ¼” NPT Quick Connect fitting, you can easily attach the system to your chamber or cabinet. The system requires a dry nitrogen tank with an appropriate pressure regulator, which is not included. Once set up, the system can be controlled using the Automatic Humidity Controller.

ETS 5465 Dry Gas Dehumidification System is specifically designed to work with ETS 5112 or 5100/5200 Series Automatic Humidity Controllers. It can be used with both the 5506A chamber and non-acrylic chambers. The system includes a solenoid valve, power cord, 10 feet of ¼” OD Polytubing, and mounting hardware. Using the ¼” NPT Quick Connect fitting, you can easily attach the system to your chamber or cabinet. The system requires a dry nitrogen tank with an appropriate pressure regulator, which is not included. Once set up, the system can be controlled using the Automatic Humidity Controller.

ETS Model 5465 Dry Gas Dehumidification System

The Model 5465 Dry Gas Dehumidification System provides the user a

solenoid valve, power cord, ten (10) feet of ¼” OD. Polytubing and mounting

hardware to enable the use of a dry nitrogen tank for purging chamber humidity.

The user will supply the nitrogen tank with an appropriate pressure regulator.

System Set-up

1. Drill and Tap a 1/4” NPT hole in side wall of the chamber or cabinet in

which the system is to be installed.

2. Place the provided 1/4” NPT Quick Connect fitting into the hole with

the threads going into the chamber, the Quick Connect head remaining

on the outside of the chamber.

3. Place the output pipe of the valve into the Quick Connect fitting.

4. Using supplied ¼” OD. Polytube, attach one end to the Quick Connect

fitting on the 5465 flow regulator input fitting. Cut the tubing to length

and attach the other end to the output of the pressure regulator on the

dry nitrogen tank.

5. Plug the power cord into the DECREASE outlet on the rear of the ETS

Model 5112 or 5100/5200 Series Automatic Humidity Controller. Make

sure the DECREASE switch is in the “OFF” position.

6. With the pressure regulator in the minimum position, open the valve on

top of the dry nitrogen tank.

7. Adjust the pressure regulator to 35 p.s.i. for operation with an ETS

Model 5506A Chamber. Higher p.s.i. may be used for non-acrylic

chambers where adequate pressure ventilation is present. A higher

p.s.i. setting will result in shorter dehumidification time.

8. Turn on the DECREASE function and open the flow regulator. The

valve should make an audible “click” when opening or closing. Turn off

the dehumidification system, it is now ready for operation.

Always turn off the dry nitrogen tank when the system is not in use.

Always provide adequate ventilation for the volume of nitrogen injected

into the chamber to avoid pressure build up inside the chamber. Contact

ETS for additional mounting options or technical support.

6/30/06

1

ETS 5465 User manual

Brand: ETS

Model: 5465

Type: User manual

ETS 5465 Dry Gas Dehumidification System is specifically designed to work with ETS 5112 or 5100/5200 Series Automatic Humidity Controllers. It can be used with both the 5506A chamber and non-acrylic chambers. The system includes a solenoid valve, power cord, 10 feet of ¼” OD Polytubing, and mounting hardware. Using the ¼” NPT Quick Connect fitting, you can easily attach the system to your chamber or cabinet. The system requires a dry nitrogen tank with an appropriate pressure regulator, which is not included. Once set up, the system can be controlled using the Automatic Humidity Controller.

Download PDF

Related papers

Other documents