Vega VEGACAL 69 Operating instructions

Operating Instructions

Capacitive double rod electrode for level

measurement

VEGACAL 69

4 … 20 mA/HART - two-wire

Document ID: 31178

2

Contents

VEGACAL 69 • 4 … 20 mA/HART - two-wire

31178-EN-170503

Contents

1 About this document

1.1 Function ........................................................................................................................... 4

1.2 Target group ..................................................................................................................... 4

1.3 Symbols used................................................................................................................... 4

2 For your safety

2.1 Authorised personnel ....................................................................................................... 5

2.2 Appropriate use ................................................................................................................ 5

2.3 Warning about incorrect use ............................................................................................. 5

2.4 General safety instructions ............................................................................................... 5

2.5 Safety label on the instrument .......................................................................................... 6

2.6 EU conformity ................................................................................................................... 6

2.7 FulllmentofNAMURrecommendations ......................................................................... 6

2.8 Installation and operation in the USA and Canada ........................................................... 6

2.9 Safety instructions for Ex areas ........................................................................................ 6

2.10 Environmental instructions ............................................................................................... 6

3 Product description

3.1 Conguration .................................................................................................................... 8

3.2 Principle of operation........................................................................................................ 9

3.3 Adjustment ..................................................................................................................... 10

3.4 Packaging, transport and storage ................................................................................... 11

3.5 Accessories and replacement parts ............................................................................... 11

4 Mounting

4.1 General instructions ....................................................................................................... 13

4.2 Mountinginstructions ..................................................................................................... 14

5 Connecting to power supply

5.1 Preparing the connection ............................................................................................... 15

5.2 Connection procedure .................................................................................................... 16

5.3 Wiring plan, single chamber housing.............................................................................. 17

5.4 Wiring plan, double chamber housing ............................................................................ 19

5.5 Wiring plan, Ex-d double chamber housing .................................................................... 21

5.6 Wiring plan - version IP 66/IP 68, 1 bar ........................................................................... 23

6 Set up with the display and adjustment module PLICSCOM

6.1 Short description ............................................................................................................ 24

6.2 Insert display and adjustment module ............................................................................ 24

6.3 Adjustment system ......................................................................................................... 25

6.4 Setup steps .................................................................................................................... 26

6.5 Menuschematic ............................................................................................................. 36

6.10 Saving the parameterisation data ................................................................................... 37

7 Set up with PACTware and other adjustment programs

7.1 Connect the PC .............................................................................................................. 38

7.2 Parameter adjustment with PACTware ............................................................................ 39

7.3 ParameteradjustmentwithAMS™andPDM ................................................................. 40

7.4 Saving the parameterisation data ................................................................................... 41

8 Maintenanceandfaultrectication

8.1 Maintenance .................................................................................................................. 42

3

Contents

VEGACAL 69 • 4 … 20 mA/HART - two-wire

31178-EN-170503

8.2 Rectify faults ................................................................................................................... 42

8.3 Exchanging the electronics module ................................................................................ 43

8.4 How to proceed if a repair is necessary .......................................................................... 44

9 Dismount

9.1 Dismounting steps.......................................................................................................... 45

9.2 Disposal ......................................................................................................................... 45

10 Supplement

10.1 Technical data ................................................................................................................ 46

10.2 Dimensions .................................................................................................................... 52

10.3 Industrial property rights ................................................................................................. 54

10.4 Trademark ...................................................................................................................... 54

Supplementary documentation

Information:

Supplementary documents appropriate to the ordered version come

withthedelivery.Youcanndthemlistedinchapter"Product descrip-

tion".

Instructions manuals for accessories and replacement parts

Tip:

ToensurereliablesetupandoperationofyourVEGACAL69,weoer

accessories and replacement parts. The corresponding documenta-

tions are:

•

27720 - VEGADIS 61

•

30531 - Electronics module VEGACAL series 60

•

34296 - Protective cover

•

31088-FlangesaccordingtoDIN-EN-ASME-JIS

Editing status: 2017-04-06

4

1 About this document

VEGACAL 69 • 4 … 20 mA/HART - two-wire

31178-EN-170503

1 About this document

1.1 Function

This operating instructions manual provides all the information you

need for mounting, connection and setup of the instrument. Further-

morethereareimportantinstructionsformaintenance,faultrectica-

tion, the exchange of parts and the safety of the user. Please read this

information before putting the instrument into operation and keep this

manual accessible in the immediate vicinity of the device.

1.2 Target group

This operating instructions manual is directed to trained specialist

personnel. The contents of this manual should be made available to

these personnel and put into practice by them.

1.3 Symbols used

Information, tip, note

This symbol indicates helpful additional information.

Caution: If this warning is ignored, faults or malfunctions can result.

Warning: If this warning is ignored, injury to persons and/or serious

damage to the instrument can result.

Danger: If this warning is ignored, serious injury to persons and/or

destruction of the instrument can result.

Ex applications

This symbol indicates special instructions for Ex applications.

SIL applications

This symbol indicates instructions for functional safety which must be

taken into account particularly for safety-relevant applications.

•

List

The dot set in front indicates a list with no implied sequence.

→

Action

This arrow indicates a single action.

1 Sequence of actions

Numbers set in front indicate successive steps in a procedure.

Battery disposal

This symbol indicates special information about the disposal of bat-

teries and accumulators.

5

2 For your safety

VEGACAL 69 • 4 … 20 mA/HART - two-wire

31178-EN-170503

2 For your safety

2.1 Authorised personnel

All operations described in this operating instructions manual must

be carried out only by trained specialist personnel authorised by the

plant operator.

During work on and with the device the required personal protective

equipment must always be worn.

2.2 Appropriate use

VEGACAL 69 is a sensor for continuous level measurement.

Youcannddetailedinformationabouttheareaofapplicationin

chapter"Product description".

Operational reliability is ensured only if the instrument is properly

usedaccordingtothespecicationsintheoperatinginstructions

manual as well as possible supplementary instructions.

For safety and warranty reasons, any invasive work on the device

beyond that described in the operating instructions manual may be

carried out only by personnel authorised by the manufacturer. Arbi-

traryconversionsormodicationsareexplicitlyforbidden.

2.3 Warning about incorrect use

Inappropriate or incorrect use of the instrument can give rise to

application-specichazards,e.g.vesseloverllordamagetosystem

components through incorrect mounting or adjustment. Thus dam-

age to property, to persons or environmental contamination can be

caused. Also the protective characteristics of the instrument can be

inuenced.

2.4 General safety instructions

This is a state-of-the-art instrument complying with all prevailing

regulations and directives. The instrument must only be operated in a

technicallyawlessandreliablecondition.Theoperatorisresponsi-

ble for the trouble-free operation of the instrument. When measuring

aggressive or corrosive media where a malfunction of the instrument

can cause a danger, the operator has to convince himself on the cor-

rect function of the instrument by taking suitable measures.

During the entire duration of use, the user is obliged to determine the

compliance of the necessary occupational safety measures with the

current valid rules and regulations and also take note of new regula-

tions.

The safety instructions in this operating instructions manual, the na-

tional installation standards as well as the valid safety regulations and

accident prevention rules must be observed by the user.

For safety and warranty reasons, any invasive work on the device

beyond that described in the operating instructions manual may be

carried out only by personnel authorised by the manufacturer. Arbi-

traryconversionsormodicationsareexplicitlyforbidden.Forsafety

6

2 For your safety

VEGACAL 69 • 4 … 20 mA/HART - two-wire

31178-EN-170503

reasons,onlytheaccessoryspeciedbythemanufacturermustbe

used.

To avoid any danger, the safety approval markings and safety tips on

the device must also be observed and their meaning looked up in this

operating instructions manual.

2.5 Safety label on the instrument

The safety approval markings and safety tips on the device must be

observed.

2.6 EU conformity

ThedevicefullsthelegalrequirementsoftheapplicableEUdirec-

tives.ByaxingtheCEmarking,weconrmsuccessfultestingofthe

product.

YoucanndtheEUconformitydeclarationonourwebsiteunder

www.vega.com/downloads.

2.7 FulllmentofNAMURrecommendations

NAMURistheautomationtechnologyuserassociationintheprocess

industryinGermany.ThepublishedNAMURrecommendationsare

acceptedasthestandardineldinstrumentation.

ThedevicefullstherequirementsofthefollowingNAMURrecom-

mendations:

•

NE 21 – Electromagnetic compatibility of equipment

•

NE 43 – Signal level for fault information from measuring transduc-

ers

•

NE53–Compatibilityofelddevicesanddisplay/adjustment

components

For further information see www.namur.de.

2.8 Installation and operation in the USA and

Canada

This information is only valid for USA and Canada. Hence the follow-

ing text is only available in the English language.

Installations in the US shall comply with the relevant requirements of

the National Electrical Code (ANSI/NFPA 70).

Installations in Canada shall comply with the relevant requirements of

the Canadian Electrical Code

2.9 Safety instructions for Ex areas

PleasenotetheEx-specicsafetyinformationforinstallationandop-

eration in Ex areas. These safety instructions are part of the operating

instructions manual and come with the Ex-approved instruments.

2.10 Environmental instructions

Protection of the environment is one of our most important duties.

That is why we have introduced an environment management system

7

2 For your safety

VEGACAL 69 • 4 … 20 mA/HART - two-wire

31178-EN-170503

with the goal of continuously improving company environmental pro-

tection.Theenvironmentmanagementsystemiscertiedaccording

to DIN EN ISO 14001.

Pleasehelpusfullthisobligationbyobservingtheenvironmental

instructions in this manual:

•

Chapter"Packaging, transport and storage"

•

Chapter"Disposal"

8

3 Product description

VEGACAL 69 • 4 … 20 mA/HART - two-wire

31178-EN-170503

3 Product description

3.1 Conguration

The scope of delivery encompasses:

•

Level sensor VEGACAL 69

•

Documentation

– This operating instructions manual

– SafetyManual"Functional safety (SIL)"(optional)

– Supplementaryinstructionsmanual"Heating for display and

adjustment module"(optional)

– Supplementaryinstructionsmanual"Plug connector for con-

tinuously measuring sensors"(optional)

– Ex-specic"Safety instructions"(withExversions)

– Ifnecessary,furthercerticates

The VEGACAL 69 consists of the components:

•

Processttingwithprobe

•

Housing with electronics

•

Housing cover, optionally available with display and adjustment

module

1

2

3

Fig. 1: VEGACAL 69 - double rod probe with plastic housing

1 Housing lid with integrated display and adjustment module (optional)

2 Housing with electronics

3 Processtting

Thetypelabelcontainsthemostimportantdataforidenticationand

use of the instrument:

Scope of delivery

Constituent parts

Type label

9

3 Product description

VEGACAL 69 • 4 … 20 mA/HART - two-wire

31178-EN-170503

2

1

11

13

12

14

15

10

9

3

6

4

5

7

8

Fig. 2: Layout of the type label (example)

1 Instrument type

2 Product code

3 Approvals

4 Process and ambient temperature, process pressure

5 Power supply and signal output, electronics

6 Protection rating

7 Probe length

8 Order number

9 Serial number of the instrument

10 Material, wetted parts

11 Symbol of the device protection class

12 Reminder to observe the instrument documentation

13 ID numbers, instrument documentation

14 NotiedauthorityforCEmarking

15 Approval directives

With the serial number, you can access the delivery data of the instru-

mentvia"www.vega.com","VEGA Tools"and"Instrument search".

Youcanndtheserialnumberontheinsideoftheinstrumentaswell

as on the type label on the outside.

3.2 Principle of operation

VEGACAL 69 is a level sensor for continuous level measurement of

liquids in non-conductive vessels or of corrosive liquids.

The double rod probe is fully insulated and highly resistant.

Probes and measured product form an electrical capacitor. The

capacitanceisinuencedbythreemainfactors.

Application area

Functional principle

10

3 Product description

VEGACAL 69 • 4 … 20 mA/HART - two-wire

31178-EN-170503

1

2

3

Fig. 3: Functional principle - Plate capacitor

1 Distance between the electrode surfaces

2 Size of the electrode surfaces

3 Type of dielectric between the electrodes

The two probes are the capacitor plates. The measured product is

the dielectric. Due to the higher dielectric constant of the product

compared to air, the capacitance increases as the material gradually

covers the probe.

The capacitance as well as the resistance change are converted by

the electronics module into a level-proportional signal.

4 … 20 mA/HART two-wire electronics for voltage supply and meas-

ured value transmission on the same cable.

Thesupplyvoltagerangecandierdependingontheinstrument

version.

Thedataforpowersupplyarespeciedinchapter"Technical data".

The backlight of the display and adjustment module is powered by

the sensor. The prerequisite for this is a supply voltage at a certain

level.Theexactvoltagespecicationsarestatedinchapter"Technical

data".

Theoptionalheatingrequiresitsownpowersupply.Youcannd

furtherdetailsinthesupplementaryinstructionsmanual"Heating for

display and adjustment module".

This function is generally not available for approved instruments.

3.3 Adjustment

The instrument can be adjusted with the following adjustment media:

•

With the display and adjustment module

•

withthesuitableVEGADTMinconjunctionwithanadjustment

softwareaccordingtotheFDT/DTMstandard,e.g.PACTwareand

PC

•

Withmanufacturer-specicadjustmentprogramsAMS™orPDM

•

With a HART handheld

Voltage supply

11

3 Product description

VEGACAL 69 • 4 … 20 mA/HART - two-wire

31178-EN-170503

3.4 Packaging, transport and storage

Your instrument was protected by packaging during transport. Its

capacity to handle normal loads during transport is assured by a test

based on ISO 4180.

The packaging of standard instruments consists of environment-

friendly, recyclable cardboard. For special versions, PE foam or PE

foil is also used. Dispose of the packaging material via specialised

recycling companies.

Transport must be carried out in due consideration of the notes on the

transport packaging. Nonobservance of these instructions can cause

damage to the device.

The delivery must be checked for completeness and possible transit

damage immediately at receipt. Ascertained transit damage or con-

cealed defects must be appropriately dealt with.

Up to the time of installation, the packages must be left closed and

stored according to the orientation and storage markings on the

outside.

Unless otherwise indicated, the packages must be stored only under

the following conditions:

•

Not in the open

•

Dry and dust free

•

Not exposed to corrosive media

•

Protected against solar radiation

•

Avoiding mechanical shock and vibration

•

Storageandtransporttemperatureseechapter"Supplement -

Technical data - Ambient conditions"

•

Relative humidity 20 … 85 %

With an instrument weight of more than 18 kg (39.68 lbs) suitable and

approved equipment must be used for lifting and carrying.

3.5 Accessories and replacement parts

ThedisplayandadjustmentmodulePLICSCOMisusedformeasured

value indication, adjustment and diagnosis. It can be inserted into the

sensor and removed at any time.

The integrated Bluetooth module (optional) enables wireless adjust-

ment via standard adjustment devices:

1)

•

Smartphone/tablet (iOS or Android operating system)

•

PC/notebook with Bluetooth USB adapter (Windows operating

system)

Youcanndfurtherinformationintheoperatinginstructions"Display

and adjustment module PLICSCOM"(Document-ID27835).

Packaging

Transport

Transport inspection

Storage

Storage and transport

temperature

Lifting and carrying

PLICSCOM

1)

Bluetooth function with VEGADIS 82 can only be used at a later date.

12

3 Product description

VEGACAL 69 • 4 … 20 mA/HART - two-wire

31178-EN-170503

The interface adapter VEGACONNECT enables the connection of

communication-capable instruments to the USB interface of a PC. For

parameter adjustment of these instruments, the adjustment software

PACTwarewithVEGA-DTMisrequired.

Youcanndfurtherinformationintheoperatinginstructions"Interface

adapter VEGACONNECT"(Document-ID32628).

VEGADIS 82 is suitable for measured value indication and adjustment

of sensors with HART protocol. It is looped into the 4 … 20 mA/HART

signal cable.

Youcanndfurtherinformationintheoperatinginstructions

"VEGADIS 82 4 … 20 mA/HART"(Document-ID45300).

The protective cover protects the sensor housing against soiling and

intense heat from solar radiation.

Youwillndadditionalinformationinthesupplementaryinstructions

manual"Protective cover"(Document-ID34296).

Screwedangesareavailableindierentversionsaccordingtothe

followingstandards:DIN2501,EN1092-1,BS10,ASMEB16.5,

JISB2210-1984,GOST12821-80.

Youcanndadditionalinformationinthesupplementaryinstructions

manual"Flanges according to DIN-EN-ASME-JIS".

VEGACONNECT

VEGADIS 82

Protectiv

e cover

Flanges

13

4Mounting

VEGACAL 69 • 4 … 20 mA/HART - two-wire

31178-EN-170503

4 Mounting

4.1 General instructions

Makesurethatallpartsoftheinstrumentcomingindirectcontact

with the process, especially the sensor element, process seal and

processtting,aresuitablefortheexistingprocessconditions,such

as process pressure, process temperature as well as the chemical

properties of the medium.

Youcanndthespecicationsinchapter"Technical data"andonthe

nameplate.

The instrument is suitable for standard and extended ambient condi-

tions acc. to DIN/EN/IEC/ANSI/ISA/UL/CSA 61010-1.

Select an installation position you can easily reach for mounting and

connectingaswellaslaterretrottingofadisplayandadjustment

module. The housing can be rotated by 330° without the use of any

tools. You can also install the display and adjustment module in four

dierentpositions(eachdisplacedby90°).

Before beginning the welding work, remove the electronics module

from the sensor. By doing this, you avoid damage to the electronics

through inductive coupling.

Ground the probe before welding directly on the rod or cable.

Usetherecommendedcables(seechapter"Connecting to power

supply")andtightenthecablegland.

You can give your instrument additional protection against moisture

penetration by leading the connection cable downward in front of the

cableentry.Rainandcondensationwatercanthusdraino.Thisap-

plies mainly to outdoor mounting as well as installation in areas where

high humidity is expected (e.g. through cleaning processes) or on

cooled or heated vessels.

To maintain the housing protection, make sure that the housing lid is

closed during operation and locked, if necessary.

Makesurethatthedegreeofcontaminationspeciedinchapter

"Technicaldata"meetstheexistingambientconditions.

Fig. 4: Measures against moisture ingress

Suitability for the process

conditions

Suitability for the ambient

conditions

Installation position

Welding work

Moisture

14

4Mounting

VEGACAL 69 • 4 … 20 mA/HART - two-wire

31178-EN-170503

Theprocessttingmustbesealedifthereisgaugeorlowpressurein

the vessel. Before use, check if the seal material is resistant against

the measured product and the process temperature.

Themax.permissiblepressureisspeciedinchapter"Technical

data"oronthetypelabelofthesensor.

Metric threads

In the case of instrument housings with metric thread, the cable

glands are screwed in at the factory. They are sealed with plastic

plugs as transport protection.

You have to remove these plugs before electrical connection.

NPTthread

In the case of instrument housings with self-sealing NPT threads, it is

not possible to have the cable entries screwed in at the factory. The

free openings for the cable glands are therefore covered with red dust

protection caps as transport protection.

Prior to setup you have to replace these protective caps with ap-

proved cable glands or close the openings with suitable blind plugs.

4.2 Mounting instructions

Iftheinstrumentismountedinthellingstream,unwantedfalse

measurement signals can be generated. For this reason, mount the

instrument at a position in the vessel where no disturbances, e.g. from

llingopenings,agitators,etc.,canoccur.

This applies particularly to instrument versions with a longer probe.

Fig.5:Inowingmedium

Pressure/Vacuum

Cableentries-NPT

thread

Cable glands

Inowingmedium

15

5 Connecting to power supply

VEGACAL 69 • 4 … 20 mA/HART - two-wire

31178-EN-170503

5 Connecting to power supply

5.1 Preparing the connection

Always keep in mind the following safety instructions:

Warning:

Connect only in the complete absence of line voltage.

•

The electrical connection must only be carried out by trained

personnel authorised by the plant operator.

•

If overvoltage surges are expected, overvoltage arresters should

be installed.

Power supply and current signal are carried on the same two-wire

cable.Theoperatingvoltagecandierdependingontheinstrument

version.

Thedataforpowersupplyarespeciedinchapter"Technical data".

Provide a reliable separation between the supply circuit and the

mains circuits according to DIN EN 61140 VDE 0140-1.

Power the instrument via an energy-limited circuit acc. to DIN/EN/IEC/

ANSI/ISA/UL/CSA 61010-1, e.g. via Class 2 power supply unit acc. to

UL 1310 or an SELV power supply unit with suitable external current

limitation.

2)

Keepinmindthefollowingadditionalfactorsthatinuencetheoperat-

ing voltage:

•

Lower output voltage of the power supply unit under nominal load

(e.g. with a sensor current of 20.5 mA or 22 mA in case of fault)

•

Inuenceofadditionalinstrumentsinthecircuit(seeloadvaluesin

chapter"Technical data")

The instrument is connected with standard two-wire cable without

screen. If electromagnetic interference is expected which is above the

test values of EN 61326-1 for industrial areas, screened cable should

be used.

Makesurethatthecableusedhastherequiredtemperatureresist-

anceandresafetyformax.occurringambienttemperature

Use cable with round cross section for instruments with housing and

cablegland.Toensurethesealeectofthecablegland(IPprotection

rating),ndoutwhichcableouterdiameterthecableglandissuitable

for.

Useacableglandttingthecablediameter.

We generally recommend the use of screened cable for HART

multidrop mode.

Safety instructions

Voltage supply

Connection cable

2)

Class 2 power supply unit: limited voltage and power level, special insulation

against circuits with higher voltage. SELV (Safety Extra Low Voltage) power

supply unit: limited voltage level, special insulation against circuits with

higher voltage

16

5 Connecting to power supply

VEGACAL 69 • 4 … 20 mA/HART - two-wire

31178-EN-170503

Metric threads

In the case of instrument housings with metric thread, the cable

glands are screwed in at the factory. They are sealed with plastic

plugs as transport protection.

You have to remove these plugs before electrical connection.

NPTthread

In the case of instrument housings with self-sealing NPT threads, it is

not possible to have the cable entries screwed in at the factory. The

free openings for the cable glands are therefore covered with red dust

protection caps as transport protection.

Prior to setup you have to replace these protective caps with ap-

proved cable glands or close the openings with suitable blind plugs.

On plastic housings, the NPT cable gland or the Conduit steel tube

must be screwed into the threaded insert without grease.

If screened cable is required, we recommend connecting the cable

screen on both ends to ground potential. In the sensor, the screen

must be connected directly to the internal ground terminal. The

ground terminal on the outside of the housing must be connected to

the ground potential (low impedance).

In Ex systems, the grounding is carried out according to the installa-

tion regulations.

In electroplating plants as well as plants that apply cathodic corro-

sionprotection,itmustbetakenintoaccountthatsignicantpotential

dierencesexist.Thiscanleadtounacceptablyhighcurrentsinthe

cable screen if it is grounded at both ends.

Information:

Themetallicpartsoftheinstrument(processtting,housing,etc.)are

conductively connected to the ground terminal.

Take note of the corresponding installation regulations for Ex applica-

tions. In particular, make sure that no potential equalisation currents

owoverthecablescreen.Incaseofgroundingonbothsidesthis

can be achieved by the use of a capacitor or a separate potential

equalisation.

5.2 Connection procedure

Proceed as follows:

1. Unscrew the housing lid

2. If a display and adjustment module is installed, remove it by turn-

ing it to the left.

3. Loosen compression nut of the cable gland and remove blind

plug

4. Remove approx. 10 cm (4 in) of the cable mantle, strip approx.

1 cm (0.4 in) of insulation from the ends of the individual wires

5. Insert the cable into the sensor through the cable entry

Cable glands

Cable screening and

grounding

17

5 Connecting to power supply

VEGACAL 69 • 4 … 20 mA/HART - two-wire

31178-EN-170503

6. Lift the opening levers of the terminals with a screwdriver (see

following illustration)

7. Insert the wire ends into the open terminals according to the wir-

ing plan

Fig. 6: Connection steps 6 and 7

8. Press down the opening levers of the terminals, you will hear the

terminal spring closing

9. Check the hold of the wires in the terminals by lightly pulling on

them

10. Connect the screen to the internal ground terminal, connect the

external ground terminal to potential equalisation

11. Tighten the compression nut of the cable entry gland. The seal

ring must completely encircle the cable

12. Screw the housing lid back on

Theelectricalconnectionisnished.

5.3 Wiring plan, single chamber housing

The following illustrations apply to the non-Ex as well as to the Ex-ia

version.

18

5 Connecting to power supply

VEGACAL 69 • 4 … 20 mA/HART - two-wire

31178-EN-170503

5

1 2

4

3

Fig. 7: Material versions, single chamber housing

1 Plastic

2 Aluminium

3 Stainless steel (precision casting)

4 Stainless steel (electro-polished)

5 Filter element for air pressure compensation of all material versions. Blind

plug with version IP 66/IP 68, 1 bar for Aluminium and stainless steel

I

²

C

Display

12 5678

3

4

1

2

Fig. 8: Electronics and terminal compartment - single chamber housing

1 Plug connector for VEGACONNECT (I²C interface)

2 Spring-loaded terminals for connection of the external indication VEGADIS

61

3 Ground terminal for connection of the cable screen

4 Spring-loaded terminals for voltage supply

Housing overview

Electronics and terminal

compartment

19

5 Connecting to power supply

VEGACAL 69 • 4 … 20 mA/HART - two-wire

31178-EN-170503

I

2

C

Display

1

12 5 678

Fig. 9: Wiring plan - single chamber housing

1 Voltage supply, signal output

5.4 Wiring plan, double chamber housing

The following illustrations apply to the non-Ex as well as to the Ex-ia

version.

1 2 3

4

5

Fig. 10: Double chamber housing

1 Housing cover - connection compartment

2 Blind plug or plug M12 x 1 for VEGADIS 61 (optional)

3 Housing cover - electronics compartment

4 Filter element for air pressure compensation

5 Cable gland

Wiring plan

Housing overview

20

5 Connecting to power supply

VEGACAL 69 • 4 … 20 mA/HART - two-wire

31178-EN-170503

1

3

2

Display

12 5678

I

²

C

Fig. 11: Electronics compartment - double chamber housing

1 Plug connector for VEGACONNECT (I²C interface)

2 Internal connection cable to the connection compartment

3 Terminals for VEGADIS 81

1

2

3

Display

12

I

2

C

Fig. 12: Terminal compartment - double chamber housing

1 Spring-loaded terminals for voltage supply

2 Plug connector for VEGACONNECT (I²C interface)

3 Ground terminal for connection of the cable screen

Electronics compartment

Terminal compartment

Page is loading ...

Vega VEGACAL 69 Operating instructions

Vega VEGACAL 69 Operating instructions

Related papers

Other documents