IFM Electronic VSA003 Installation guide

Type
Installation guide

IFM Electronic VSA003 vibration sensor is a compact and reliable device designed to detect vibrations in machines and equipment. It is commonly used in industrial settings to monitor the performance of rotating machinery, such as pumps, motors, and fans. By detecting excessive vibrations, the VSA003 can help prevent costly breakdowns and improve overall equipment reliability.

The VSA003 is easy to install and can be mounted directly on the machine surface using glue or a mounting screw. It features a shielded cable to minimize electrical interference and ensure accurate readings. The sensor's output signal can be connected to diagnostic electronics, such as the IFM Electronic VSExxx series, for further analysis and monitoring.

IFM Electronic VSA003 vibration sensor is a compact and reliable device designed to detect vibrations in machines and equipment. It is commonly used in industrial settings to monitor the performance of rotating machinery, such as pumps, motors, and fans. By detecting excessive vibrations, the VSA003 can help prevent costly breakdowns and improve overall equipment reliability.

The VSA003 is easy to install and can be mounted directly on the machine surface using glue or a mounting screw. It features a shielded cable to minimize electrical interference and ensure accurate readings. The sensor's output signal can be connected to diagnostic electronics, such as the IFM Electronic VSExxx series, for further analysis and monitoring.

Installation instructions
Vibration sensor
VSA003 
VSA004 
VSA005
704577/02 09/2010
UK
2
Contents
1 Preliminary note ���������������������������������������������������������������������������������������������������3
2 Safety instructions �����������������������������������������������������������������������������������������������3
3 Functions and features ����������������������������������������������������������������������������������������3
4 Electrical connection ��������������������������������������������������������������������������������������������3
4�1 Use of a screened cable for VSAx sensors ���������������������������������������������������4
4�2 Setting instructions ����������������������������������������������������������������������������������������4
5 Installation������������������������������������������������������������������������������������������������������������4
6 Scale drawing ������������������������������������������������������������������������������������������������������5
7 Approval (Limited voltage / Current) ��������������������������������������������������������������������5
8 Maintenance, repair and disposal ������������������������������������������������������������������������5
9 Technical data ������������������������������������������������������������������������������������������������������5
3
UK
1  Preliminary note
An instruction is indicated by „►“:
Example: ► Mount the unit as shown�
Important note
Non-compliance can result in malfunction or interference�
Information
Supplementary note�
2  Safety instructions
Please read the operating instructions prior to set-up of the device� Ensure that
the product is suitable for your application without any restrictions�
The unit conforms to the relevant regulations and EC directives�
Improper or non-intended use may lead to malfunctions of the unit or to
unwanted effects in your application�
Installation, electrical connection, set-up, operation and maintenance of the
unit must only be carried out by qualified personnel authorised by the machine
operator
3  Functions and features
Vibration detection of machines and equipment
For connection to diagnostic electronics VSExxx
4  Electrical connection
The unit must be connected by a qualified electrician�
The national and international regulations for the installation of electrical
equipment must be adhered to�
Disconnect power
Connect the unit�
Wiring blue: GND / black: test / brown: L+ / white: out
shield wire: screen
4
4.1  Use of a screened cable for VSAx sensors
Use a screened cable to avoid conducted interference�
Connect the screened cable to the DIN rail in the control cabinet�
For wired units, the screen is connected to the sensor housing�
VSA
VSE
1: screen
2: DIN rail
4.2  Setting instructions
Enter the scaling for the sensor in the configuration software VES003�
If the sensor is connected to channel 1:
VSA003: settings → Sensors → Sensor 1 → 17500 mg
VSA004 / VSA005 : settings → Sensors → Sensor 1 → 25000 mg
If the sensor is connected to channel 2:
VSA003: settings → Sensors → Sensor 2 → 17500 mg
VSA004 / VSA005: settings → Sensors → Sensor 2 → 25000 mg etc�
5  Installation
Mount only in a thick housing wall and vertical to the machine surface close to
the bearing or at the end shield�
Ensure that the signal direction is correct�
Ensure a safe vibration transmission and allow no elastic intermediate layers�
Fixing with glue or mounting screw (Torx cylinder screw no� 15, recommended
tightening torque 5 Nm, M5 x 20, Ø hexagon socket 3�4 mm)
For fixing, use a screw retaining compound�
5
UK
6  Scale drawing
18
11,5
H
L
5,5
1
Dimensions in mm
1: shield wire
H = 12 (VSA003)
H = 13�5 (VSA004, VSA005)
L = 1�5 m (VSA003)
L = 3 m(VSA004)
L = 10 m (VSA005)
7  Approval (Limited voltage / Current)
The device shall be supplied from an isolating transformer having a secondary
Listed fuse rated 1�0 A�
8  Maintenance, repair and disposal
If used correctly no maintenance and repair measures are necessaryAfter use
dispose of the unit in an environmentally friendly way in accordance with the
applicable national regulations�
9  Technical data
Technical data and further information at www�ifm�com
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5

IFM Electronic VSA003 Installation guide

Type
Installation guide

IFM Electronic VSA003 vibration sensor is a compact and reliable device designed to detect vibrations in machines and equipment. It is commonly used in industrial settings to monitor the performance of rotating machinery, such as pumps, motors, and fans. By detecting excessive vibrations, the VSA003 can help prevent costly breakdowns and improve overall equipment reliability.

The VSA003 is easy to install and can be mounted directly on the machine surface using glue or a mounting screw. It features a shielded cable to minimize electrical interference and ensure accurate readings. The sensor's output signal can be connected to diagnostic electronics, such as the IFM Electronic VSExxx series, for further analysis and monitoring.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI